Page 1793 of 4323
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
DI±1591
1785 Author: Date:
2005 SEQUOIA (RM1146U)
4 Does the system operate normally after replacement of transponder key ECU?
YES Replace transponder key ECU.
NO
Replace ECM (See page IN±35).
Page 1794 of 4323

DI±1592
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
1786 Author: Date:
2005 SEQUOIA (RM1146U)
Code 31, 35, 36 or 37 is output.
CIRCUIT DESCRIPTION
These DTCs are indicated when an unregistered key is inserted. When any of them is indicated, clear the
DTC and insert other registed keys to check for DTCs.
When a key that outputs a DTC (31, 35, 36 or 37) is found, register this key. When a DTC (31, 35, 36 or 37)
is not output, there is a possibility that the unregistered key has been inserted before. (The ECM is normal.)
Ask the customer under what conditions the problem occurred to find the cause.
(Example: Another key has been inserted, etc.)
DTC No.DTC Detecting ConditionTrouble Area
31, 35, 36, 37Unmatched key codeKey
INSPECTION PROCEDURE
1 Delete DTC and insert all the presently available keys to check whether the en-
gine starts or not (See page DI±1576).
HINT:
When inserting a key that does not start the engine, a DTC (31, 35, 36 or 37) is stored in memory.
RESULT:
OKAll keys start the engine.
NGA specific key does not start the engine.
OK No problem.
HINT:
If the result is ºOKº, confirm whether or not the customer ever
inserted an unregistered key or the immobiliser key (with a
transponder chip) of another vehicle into the ignition key cylin-
der, and find out the cause of the detection of the DTC.
NG
Register the key that does not start the en-
gine
(See page BE±137).
DIABH±04
Page 1795 of 4323
I24830
ECMT16
Transponder Key ECU
IMI
IMO16
15P±G
11
10EFIO
EFII L±Y E5
E5
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
DI±1593
1787 Author: Date:
2005 SEQUOIA (RM1146U)
Code 32 or 33 is output
CIRCUIT DESCRIPTION
The transponder key ECU indicates DTC 32 when a key without a key code is inserted, and indicates DTC
33 when a key code cannot be identified.
HINT:
DTCs 32 and 33 are abnormal codes.
DTC No.DTC Detecting ConditionTrouble Area
32, 33Communication error
Key
Transponder key ECU
Wire harness
WIRING DIAGRAM
DIABI±04
Page 1796 of 4323
DI±1594
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
1788 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Check whether the engine can be started with a spare key of the same vehicle.
YES Replace key.
NO
2 Check harness and connector between transponder key ECU and ECM (See
page IN±35).
NG Repair or replace harness or connector.
OK
3 Does the system operate normally after replacement of transponder key ECU?
YES Replace transponder key ECU.
NO
Replace ECM (See page IN±35).
Page 1797 of 4323
I24831
Transponder Key ECU
Sub J/B No. 3
+B
J43
J/C
51
O
BatteryF10
FL BlockW±R
B
4
IG BEngine Room J/B W±R32
1J
1E Instrument Panel J/B
A
AGND O14
T16 T16 1
2
W±R
3A 3B
81
2C
2D ECU±B
SHORT PIN
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
DI±1595
1789 Author: Date:
2005 SEQUOIA (RM1146U)
Power source circuit
CIRCUIT DESCRIPTION
This circuit provides power to operate the transponder key ECU.
WIRING DIAGRAM
DI7TO±07
Page 1798 of 4323
DI±1596
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
1790 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Check ECU±B fuse.
CHECK:
Check for continuity of the ECU±B fuse.
OK:
Continuity
NG Replace fuse.
OK
2 Check voltage between terminals +B and GND of transponder key ECU connec-
tor.
PREPARATION:
(a) Turn the ignition switch OFF.
(b) Disconnect the transponder key ECU connector.
CHECK:
Measure the voltage between terminals +B and GND.
OK:
Voltage: 10 to 14 V
OK Proceed to next circuit inspection shown in
problem symptoms table (See page DI±1573).
NG
3 Check wire harness and connector between terminal GND of transponder key
ECU and body ground (See page IN±35).
NG Repair or replace wire harness or connector.
OK
Check and repair wire harness and connec-
tor between transponder key ECU and bat-
tery.
Page 1799 of 4323
I24835
Instrument Panel J/B
6 9
BR
1F 1D W±B
A
IEJ8
J/C12
C6C516
LG±B7
T16IND Combination MeterTransponder Key ECU
Security
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
DI±1597
1791 Author: Date:
2005 SEQUOIA (RM1146U)
Security Indicator Light Circuit
CIRCUIT DESCRIPTION
When the transponder key is registered, the transponder key ECU outputs the key registration condition by
illuminating, blinking or turning off the security indicator.
WIRING DIAGRAM
DIABJ±03
Page 1800 of 4323
I24836
ON
IND
(±) (+)
DI±1598
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
1792 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Check voltage between terminal IND of transponder key ECU connector and
body ground.
PREPARATION:
Turn the ignition switch to the ON position and enter diagnosis
mode.
CHECK:
Measure the voltage between terminal IND of the transponder
key ECU connector and body ground when the security indica-
tor light is on and when it is off.
OK:
Indicator lightVoltage
ON3 to 6 V
OFFBelow 1 V
NG Proceed to next circuit inspection shown in
problem symptoms table (See page DI±1573).
OK
2 Check combination meter (See page DI±1610).
NG Replace combination meter.
OK
Check and replace wire harness and connec-
tor (See page IN±35).