Page 3105 of 4323

SA24B±02
F14284
Socket Wrench
F14286
F14287
SST
SST
F14288
SST
SST
± SUSPENSION AND AXLEREAR AXLE SHAFT
SA±101
3097 Author: Date:
2005 SEQUOIA (RM1146U)
REASSEMBLY
1. INSTALL BEARING ASSEMBLY
Position the backing plate on the bearing assembly and using
a press and 2 socket wrenches, install the serration bolts.
2. INSTALL OIL DEFLECTOR AND GASKET
Position a new gasket and oil deflector on the axle shaft and
install a washer and nut to a new hub bolt, as shown in the il-
lustration, and install the hub bolt by torquing the nut.
3. INSTALL REAR AXLE SHAFT TO BACKING PLATE
(a) Install the backing plate, spring washer and bearing re-
tainer on the rear axle shaft.
(b) Using SST and a press, install the rear axle shaft into the
backing plate.
SST 09631±12090, 09950±60020 (09951±01030)
4. INSTALL SNAP RING TO AXLE SHAFT
Using a snap ring expander, install a new snap ring.
5. INSTALL SPEED SENSOR ROTOR AND BEARING RE-
TAINER (DIFFERENTIAL SIDE)
Using SST and a press, install a new speed sensor rotor and
bearing retainer.
SST 09631±12090, 09950±60020 (09951±01030)
Standard length: 132.8 ± 1.0 mm (5.228 ± 0.039 in.)
Page 3106 of 4323
SA17X±07
SA±102
± SUSPENSION AND AXLEREAR AXLE SHAFT
3098 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
Installation is in the reverse order of removal (See page SA±95).
HINT:
After installation, fill the brake reservoir with brake fluid, bleed the brake system (See page BR±4), check
for leaks and check the speed sensor signal (See page DI±899).
Page 3107 of 4323
SA24C±02
F14274
F14290
Nut
Washer
± SUSPENSION AND AXLEREAR WHEEL HUB BOLT
SA±103
3099 Author: Date:
2005 SEQUOIA (RM1146U)
REAR WHEEL HUB BOLT
REPLACEMENT
1. REMOVE REAR WHEEL
2. REMOVE BRAKE CALIPER AND DISC
(a) Remove the 2 bolts, brake caliper and disc.
(b) Support the brake caliper securely.
3. REMOVE HUB BOLT (See page SA±97)
4. INSTALL HUB BOLT
Install a washer and nut to a new hub bolt, as shown in the il-
lustration. Install the hub bolt by torquing the nut, while holding
the axle shaft using a brass bar or an equivalent.
5. INSTALL DISC AND BRAKE CALIPER
Install the disc and brake caliper with the 2 bolts.
Torque: 105 N´m (1,070 kgf´cm, 77 ft´lbf)
6. INSTALL REAR WHEEL
Torque: 110 N´m (1,150 kgf´cm, 83 ft´lbf)
Page 3108 of 4323
SA15K±09
F14321
Oil Seal
Front Bearing
Bearing Spacer
N´m (kgf´cm, ft´lbf) : Specified torque
Non±reusable partCompanion Flange
Rear Propeller ShaftWasher
74 (750, 54)
Drive Pinion
2WD:
10 (102, 7.4)
74 (750, 54)
See page SA±119
Stud BoltCompanion
Flange
See page SA±119
SA±104
± SUSPENSION AND AXLEREAR DIFFERENTIAL FRONT OIL SEAL
3100 Author: Date:
2005 SEQUOIA (RM1146U)
REAR DIFFERENTIAL FRONT OIL SEAL
COMPONENTS
Page 3109 of 4323
SA24D±04
F14486
40 mm
(1.57 in.)
F14485
SST
F14484
SST
± SUSPENSION AND AXLEREAR DIFFERENTIAL FRONT OIL SEAL
SA±105
3101 Author: Date:
2005 SEQUOIA (RM1146U)
REPLACEMENT
1. DRAIN DIFFERENTIAL OIL
2. DISCONNECT REAR PROPELLER SHAFT
2WD: See page PR±3
4WD: See page PR±7
3. REMOVE COMPANION FLANGE
(a) 2WD:
Remove the companion flange nut.
(1) Using a chisel and hammer, loosen the staked part
of the nut.
(2) Install the 3 stud bolts so that the heads come out
40 mm (1.57 in.).
(3) Set the SST and install the 3 nuts to the companion
flange.
SST 09213±58013
(4) Install the other SST to the set SST to hold the com-
panion flange, and remove the nut.
SST 09330±00021
(5) Remove the 3 nuts, SST and stud bolts from the
companion flange.
Page 3110 of 4323
SA2349
SST
R13357
SST
R13358
SST SST
R13359
SST SA±106
± SUSPENSION AND AXLEREAR DIFFERENTIAL FRONT OIL SEAL
3102 Author: Date:
2005 SEQUOIA (RM1146U)
(b) 4WD:
(1) Using a chisel and hammer, loosen the staked part
of the nut.
(2) Using SST to hold the flange, remove the nut.
SST 09330±00021
(c) Using SST, remove the companion flange.
SST 09950±30012 (09951±03010, 09953±03010,
09954±03010, 09955±03030, 09956±03050)
4. REMOVE OIL SEAL
Using SST, remove the oil seal.
SST 09308±10010
5. REMOVE FRONT BEARING
Using SST, remove the front bearing from the drive pinion.
SST 09556±22010
6. REMOVE BEARING SPACER
(a) Remove the 2 washers.
(b) Remove the bearing spacer.
7. INSTALL NEW BEARING SPACER
(a) Install a new bearing spacer.
(b) Install the 2 washers.
8. INSTALL FRONT BEARING
(a) Place the front bearing.
Page 3111 of 4323

R13361
SST
R13360
SST
Vinyl Tape
F14486
40 mm
(1.57 in.)
F14485
SST
F14522SST
± SUSPENSION AND AXLEREAR DIFFERENTIAL FRONT OIL SEAL
SA±107
3103 Author: Date:
2005 SEQUOIA (RM1146U)
(b) Using SST and the companion flange, install the front
bearing then remove the companion flange.
SST 09950±30012 (09951±03010, 09953±03010,
09954±03010, 09955±03030, 09956±03050)
9. INSTALL NEW OIL SEAL
(a) Coat a new oil seal lip with MP grease.
(b) Using SST and a plastic hammer, install the oil seal until
its surface is flush with the differential carrier end.
SST 09316±12010, 09649±17010
HINT:
Connect 2 SST with vinyl tape.
10. INSTALL COMPANION FLANGE
(a) Place the companion flange on the drive pinion.
(b) Coat the threads of a new nut with hypoid gear oil.
(c) 2WD:
Install the companion flange nut.
(1) Install the 3 stud bolts so that the heads come out
40 mm (1.57 in.).
(2) Set the SST and install the 3 nuts to the companion
flange .
SST 09213±58013
(3) Install the other SST to the set SST to hold the com-
panion flange and torque the nut.
SST 09330±00021
Torque: 147 N´m (1,500 kgf´cm, 109 ft´lbf)
(4) Remove the 3 nuts, SST and stud bolts from the
companion flange.
Page 3112 of 4323
FA1083
SST
FA1084
R13337
Less than
5 mm (0.20 in.) SA±108
± SUSPENSION AND AXLEREAR DIFFERENTIAL FRONT OIL SEAL
3104 Author: Date:
2005 SEQUOIA (RM1146U)
(d) 4WD:
Using SST to hold the flange, torque the nut.
SST 09330±00021
Torque: 147 N´m (1,500 kgf´cm, 109 ft´lbf)
11. ADJUST DRIVE PINION PRELOAD
(See page SA±119)
12. STAKE DRIVE PINION NUT
13. CONNECT REAR PROPELLER SHAFT
2WD: See page PR±5
4WD: See page PR±9
14. FILL DIFFERENTIAL WITH HYPOID GEAR OIL
Torque: 49 N´m (500 kgf´cm, 36 ft´lbf)
Oil type: Hypoid gear oil API GL±5
Recommended oil viscosity:
SAE 75W ± 140 (Synthetic)
Capacity: 3.65 liters (3.86 US qts, 3.21 Imp. qts)