2001 TOYOTA SEQUOIA seat torque

B13807
A: Propeller Shaft Spiders
B: Propeller Shaft Sliding YokesAB
A
A
MA0568
MA±10
± MAINTENANCECHASSIS
57 Author: Date:
2005 SEQUOIA (RM1146U)
(b) Recoat the drive shaft thrust bush with grease (See page
SA±34).
11. 4WD:
LUBRICATE PROPELLER SHAFT AND TIGHTEN
BOLTS
(a) Lubricate the propeller shaft, referring to the lubrication
chart. Before pumping in grease, wipe off any mud and
dust on the grease fitting.
Grease grade:
Propeller shaft (Except Double±cardan joint)
Lithium base chassis grease NLGI No.2
(b) Tighten the bolts for propeller shaft.
(2WD: See page PR±5)
(4WD: See page PR±9)
12. ROTATE TIRE (See page SA±3)
13. TIGHTEN BOLTS AND NUTS ON CHASSIS AND BODY
(a) Tighten the following parts:

Seat mounting bolts
Torque:
37 N´m (375 kgf´cm, 27 ft´lbf)

B02100
± MAINTENANCECHASSIS
MA±11
58 Author: Date:
2005 SEQUOIA (RM1146U)

Leaf spring U±bolt mounting nuts
Torque: 133 N´m (1,350 kgf´cm, 98 ft´lbf )
(b) Under Severe Conditions:
In addition to the above maintenance items, check for
loose or missing bolts and nuts on the following.

Steering system

Drive train

Suspension system

Fuel tank mounts

Engine mounts, etc.
14. FINAL INSPECTION
(a) Check operation of body parts:

Hood:

Auxiliary catch operates properly

Hood locks securely when closed

Doors:

Door locks operate properly

Doors close properly

Seats:

Seat adjusts easily and locks securely in any
positions

Seat backs lock securely at any angle

Fold±down seat backs lock securely
(b) Road test:

Engine and chassis parts do not have abnormal
noises.

Vehicle does not wander or pull to one side.

Brakes work properly and do not drag.
(c) Be sure to deliver a clean vehicle and especially check:

Steering wheel

Shift lever knob

All switch knobs

Door handles

Seats

PP1BM±08
± PREPARATIONENGINE MECHANICAL
PP±7
65 Author: Date:
2005 SEQUOIA (RM1146U)
EQUIPMENT
Caliper gauge
CO/HC meter
Compression gauge
Connecting rod aligner
Cylinder gauge
Dial indicator
Dye penetrant
Engine tune±up tester
Groove cleaning tool
Heater
Magnetic finger
Micrometer
OBD II scan tool
Pin hole grinder
Piston ring compressor
Piston ring expander
Plastigage
Precision straight edge
Press
Ridge reamer
Soft brush
Solvent
Spring testerValve spring
Steel squareValve spring
Thermometer
Torque wrench
Valve seat cutter
Vernier calipers
V±block
Wire brushValve

PP0O2±06
± PREPARATIONBODY ELECTRICAL
PP±73
131 Author: Date:
2005 SEQUOIA (RM1146U)
EQUIPMENT
Voltmeter
Ammeter
Ohmmeter
Test lead
ThermometerEngine coolant temperature sender gauge, Engine oil level warn-
ing switch, Seat heater
SyphonBrake fluid level warning switch
Oil bathEngine oil level warning switch
Bulb (1.4 W)Defogger switch
Bulb (3.4 W)Fuel sender gauge, Engine coolant temperature receiver gauge,
Seat belt warning relay
Dry cell batteryFuel sender gauge, Power mirror
Heat lightSeat heater
Hexagon wrench (6 mm)Power seat
Torque wrench
Masking tapeRear window defogger wire
Tin foilRear window defogger wire

PP0SI±02
± PREPARATIONBODY
PP±77
135 Author: Date:
2005 SEQUOIA (RM1146U)
EQUIPMENT
Clip remover
Torque wrench
Hexagon wrench (6 mm)
Torx driver
Hog ring pliers
Hand riveter
TapeTo avoid surface damage
Adhesive tapeTo avoid surface damage
Double±stick tape
Adhesive
Cleaner
Shop rag
Knife
Sealer gun
Brush
Putty spatula
Glass plate or similar object
Wooden block or similar object
Heat light
Piano wire
Rope (no projections, difficult to break)Seat belt pretensioner
Tire with disk wheel Width: 185 mm (7.28 in.)
Inner diam: 360 mm (14.17 in.)Seat belt pretensioner
Vinyl bagSeat belt pretensioner

SS061±77
SS±46
± SERVICE SPECIFICATIONSSUPPLEMENTAL RESTRAINT SYSTEM
188 Author: Date:
2005 SEQUOIA (RM1146U)
SUPPLEMENTAL RESTRAINT SYSTEM
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Steering wheel set nut5051037
Steering wheel pad set screw (Torx screw)8.89078 in.´lbf
Front passenger airbag assembly x Instrument panel5.05144 in.´lbf
Front passenger airbag assembly x Instrument panel reinforcement2020415
Front seat x Body3737727
Front seat inner belt x Front seat4142831
Seatback cover x Seatback frame5.55649 in.´lbf
Armrest x Seatback frame3737727
Cutain shield airbag assembly x Body9.81007
Airbag senaor assembly x Body17.517913
Front airbag sensor x Body17.517913
Side airbag sensor assembly x Body17.517913
Curtain shield airbag sensor assembly x Body17.517913
Seat position sensor assembly x Body8.08271 in.´lbf

DI±1488
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1682 Author: Date:
2005 SEQUOIA (RM1146U)
5 Retighten front seat assembly RH bolt (see page BO±111, BO±125).
(a) Turn the ignition switch to the LOCK position.
(b) Loosen the 4 installation bolts of the front seat assembly RH.
(c) Tighten the 4 installation bolts of the front seat assembly RH to the specified torque.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
NEXT
6 Perform zero point calibration.
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position.
(c) Using the hand±held tester, perform ºZero point calibrationº (see page DI±1128).
OK:
The ºCOMPLETEDº is displayed on the tester screen.
NG Go to step 8.
OK
7 Perform sensitivity check.
Using the hand±held tester, perform ºSensitivity checkº (see page DI±1128).
OK:
Standard value: 27 to 33 kg (59.52 to 72.75 lb)
NG Go to step 8.
OK
END

A23372
Non±reusable part
N´m (kgf´cm, ft´lbf) : Specified torqueCamshaft Drive Gear
Camshaft Timing Tube
Seal WasherIntake Camshaft
Exhaust Camshaft

Camshaft Oil Seal
Camshaft Gear Spring
Camshaft Driven Sub±gear
Snap Ring Wave Washer Screw Plug
15 (150, 11)
7.5 (80, 66 in.´lbf)
Camshaft Driven Main Gear78 (790, 58)
A23323
Heat Insulator LH Exhaust Manifold
44 (450, 32)
Heat Insulator
44 (450, 32)

Gasket RH Cylinder HeadValve Lifter

Oil Seal Spring SeatValve SpringSpring RetainerAdjust Shim
Keeper

Valve Guide Bushing
Valve
RH Exhaust Manifold

Gasket LH Cylinder Head

Non±reusable part
N´m (kgf´cm, ft´lbf) : Specified torque




7.5 (76, 66 in.´lbf)
7.5 (76, 66 in.´lbf)
± ENGINE MECHANICALCYLINDER HEAD
EM±35
2614 Author: Date:
2005 SEQUOIA (RM1146U)