2001 TOYOTA SEQUOIA warning light

IN±10
± INTRODUCTIONFOR ALL OF VEHICLES
10 Author: Date:
2005 SEQUOIA (RM1146U)
(3) Even in case of a minor collision where the SRS
does not deploy, the steering wheel pad, the pas-
senger airbag assembly, side airbag assembly, cur-
tain shield airbag assembly, seat belt pretensioner,
airbag sensor assembly, front airbag sensor, side
airbag sensor assembly and curtain shield airbag
sensor assembly should be inspected.
Parts of referenceSee page
Steering wheel padSee page RS±22
Passenger side airbag assemblySee page RS±35
Side airbag assembly
Power adjuster type
Manual adjuster type
See page RS±49
See page RS±64
Curtain shield airbag assemblySee page RS±72
Seat belt pretensionerSee page BO±165
Airbag sensor assemblySee page RS±83
Front airbag sensor assemblySee page RS±88
Side airbag sensor assemblySee page RS±93
Curtain shield airbag sensor assemblySee page RS±98
(4) Never use SRS parts from another vehicle. When
replacing parts, replace them with new ones.
(5) Before repairs, remove the airbag sensor because
shocks are likely to be applied to the sensor during
repairs.
(6) Never disassemble or repair the steering wheel
pad, front passenger airbag assembly, airbag sen-
sor assembly and front airbag sensor.
(7) If the steering wheel pad, front passenger airbag
assembly, side airbag assembly, curtain shield air-
bag assembly, seat belt pretensioner, airbag sensor
assembly and front airbag sensor have been
dropped, or if there are cracks, dents or other de-
fects in the case, bracket or connector, replace
them with new ones.
(8) Do not expose the steering wheel pad, front pas-
senger airbag assembly, side airbag assembly, cur-
tain shield airbag assembly, seat belt pretensioner,
airbag sensor assembly and front airbag sensor di-
rectly to hot air or flames.
(9) Use a volt/ohmmeter with high impedance (10 kW/V
minimum) for troubleshooting of the electrical cir-
cuit.
(10) Information labels are attached to the periphery of
the SRS components. Follow the instructions on the
notices.
(11) After work on the supplemental restraint system is
completed, check the SRS warning light (See page
DI±1118).

B04770
IN±18
± INTRODUCTIONFOR ALL OF VEHICLES
18 Author: Date:
2005 SEQUOIA (RM1146U)
(4) Check that the VSC TRAC warning light blinks.
(5) After the measurement, remove the SST and re-
start the engine. At this time, make sure that the
VSC TRAC warning light is off.
(b) Notice in VSC operation.
(1) Removal and reinstallation of VSC±related compo-
nents may cause misadjustment of them. Do not re-
move or reinstall them unless necessary.
(2) When conducting VSC±related operations, do not
fail to make sure that the preparation and the finish-
ing of the operation are all performed in accordance
with the direction in this text.
3. FOR VEHICLES EQUIPPED WITH A CATALYTIC CONVERTER
CAUTION:
If a large amount of unburned gasoline flows into the converter, it may overheat and create a fire haz-
ard. To prevent this, observe the following precautions and explain them to your customer.
(a) Use only unleaded gasoline.
(b) Avoid prolonged idling.
Avoid running the engine at idle speed for more than 20 minutes.
(c) Avoid spark jump test.
(1) Perform spark jump test only when absolutely necessary. Perform this test as rapidly as possible.
(2) While testing, never race the engine.
(d) Avoid prolonged engine compression measurement.
Engine compression tests must be done as rapidly as possible.
(e) Do not run engine when fuel tank is nearly empty.
This may cause the engine to misfire and create an extra load on the converter.
(f) Avoid coasting with ignition turned off.
(g) Do not dispose of used catalyst along with parts contaminated with gasoline or oil.
4. IF VEHICLE IS EQUIPPED WITH MOBILE COMMUNICATION SYSTEM
For vehicles with mobile communication systems such as two±way radios and cellular telephones, observe
the following precautions.
(1) Install the antenna as far as possible away from the ECU and sensors of the vehicle's electronic
system.
(2) Install the antenna feeder at least 20 cm (7.87 in.) away from the ECU and sensors of the ve-
hicle's electronic systems. For details about ECU and sensor locations, refer to the section on
the applicable component.
(3) Do not wind the antenna feeder together with the other wiring as much as possible, also avoid
running the antenna feeder parallel with other wire harness.
(4) Check that the antenna and feeder are correctly adjusted.
(5) Do not install powerful mobile communication system.

IN0KL±01
± INTRODUCTIONFOR ALL OF VEHICLES
IN±21
21 Author: Date:
2005 SEQUOIA (RM1146U)
CUSTOMIZE PARAMETERS
HINT:
The following items can be customized.
NOTICE:

When a customer requests a change in a function, first make sure that customization of the
function(s) is/are possible.

Be sure to make a note of the current setting before customizing.

When troubleshooting a function, first make sure that the function is not set to OFF.

When troubleshooting, pay attention as there is a possibility that the function has been set to
SMALL through customizing (Example: In case of the symptom in which ºThe key reminder
buzzer operation does not functionº is displayed, check that the key reminder buzzer operation
is not set to SMALL, then perform troubleshooting).
METER:
DISPLAY (ITEM)DEFAULTCONTENTSSETTING
KEY REMND VOLUM
(Key reminder buzzer vol-
ume)
LARGEFunction that changes the volume of key reminder buzzer.LARGE/MEDIUM/SMALL
WIRELESS DOOR LOCK:
DISPLAY (ITEM)DEFAULTCONTENTSSETTING
WIRELESS OPERONTurns wireless door lock function ON/OFF.ON/OFF
OPEN DOOR WARNONSounds buzzer for 10 seconds when door is not completely
closed and transmitter LOCK switch is pressed.ON/OFF
AUTO LOCK DELAY30SControls amount of time from when doors are unlocked until
they are locked by automatic lock function.60S/30S
UNLOCK/2OPERON
When UNLOCK switch is pressed once, this function un±
locks only the designated door. When unlock switch is
pressed again within 3 seconds, all doors unlock. If setting is
OFF, pressing UNLOCK switch once unlocks all doors.
ON/OFF
LNT/LGT ON/UNLKONTurns on room light when wireless door lock system is oper-
ated.ON/OFF
ALARM FUNCTIONONOperates theft deterrent system when transmitter LOCK
(PANIC) switch is held for 3 seconds.ON/OFF
AUTO LOCKOFFLocks doors when the vehicle speed reaches a certain level.ON/OFF
UNLK/KEY TWICEON
Unlocks only driver's door when driver's door key cylinder is
turned to unlock once, and unlocks all doors when it is turned
to unlock twice. In OFF setting, unlocks all doors when the
cylinder is turned to unlock once.
ON/OFF
ALL UNLK/OPN±CLOFFFunction that unlocks all doors when the driver door is
opened after turning the ignition switch off.ON/OFF
UNLOCK/PARKOFFUnlocks doors when shift lever is moved to P position from
any position other than P while the ignition switch is ON.ON/OFF
THEFT:
DISPLAY (ITEM)DEFAULTCONTENTSSETTING
WARNING TIME15SChanges warning time for PASSIVE MODE.5S/15S/27.5S/60S
PASSIVE MODEOFF
Switches theft deterrent system from arming preparation
state to armed state 30 seconds after key is removed from
ignition key cylinder and driver side door is closed, even if
doors are not locked by wireless or door key lock operation.
ON/OFF
WARN BY GLS SENONFunction that switches the alarm warning on/off when glass
breakage is detected.ON/OFF

MA002±35
MA±2
± MAINTENANCEINSIDE VEHICLE
49 Author: Date:
2005 SEQUOIA (RM1146U)
INSIDE VEHICLE
GENERAL MAINTENANCE
These are maintenance and inspection items which are considered to be the owner's responsibility.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every service item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.

Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. LIGHTS
(a) Check that the headlights, stop lights, taillights, turn signal lights, and other lights are all working.
(b) Check the headlight aim.
3. WARNING LIGHTS AND BUZZERS
Check that all warning lights and buzzers function properly.
4. HORN
Check that it is working.
5. WINDSHIELD GLASS
Check for scratches, pits or abrasions.
6. WINDSHIELD WIPER AND WASHER
(a) Check operation of the wipers and washer.
(b) Check that the wipers do not streak.
7. WINDSHIELD DEFROSTER
Check that air comes out from the defroster outlet when operating the heater or air conditioner.
8. REAR VIEW MIRROR
Check that it is mounted securely.
9. SUN VISORS
Check that they move freely and are mounted securely.
10. STEERING WHEEL
Check that it has the specified free play. Be alert for changes in steering condition, such as hard steering,
excessive free play or strange noises.
11. SEATS
(a) Check that the seat adjusters operate smoothly.
(b) Check that all latches lock securely in any position.
(c) Check that the head restraints move up and down smoothly and that the locks hold securely in any
latch position.
(d) For fold±down seat backs, check that the latches lock securely.
12. SEAT BELTS
(a) Check that the seat belt system such as the buckles, retractors and anchors operate properly and
smoothly.
(b) Check that the belt webbing is not cut, frayed, worn or damaged.

PP0O2±06
± PREPARATIONBODY ELECTRICAL
PP±73
131 Author: Date:
2005 SEQUOIA (RM1146U)
EQUIPMENT
Voltmeter
Ammeter
Ohmmeter
Test lead
ThermometerEngine coolant temperature sender gauge, Engine oil level warn-
ing switch, Seat heater
SyphonBrake fluid level warning switch
Oil bathEngine oil level warning switch
Bulb (1.4 W)Defogger switch
Bulb (3.4 W)Fuel sender gauge, Engine coolant temperature receiver gauge,
Seat belt warning relay
Dry cell batteryFuel sender gauge, Power mirror
Heat lightSeat heater
Hexagon wrench (6 mm)Power seat
Torque wrench
Masking tapeRear window defogger wire
Tin foilRear window defogger wire

DIDIK±01
D13871
Combination Meter
DLC3 Stop Light SwitchECM
Park/Neutral Position SwitchSpeed Sensor (SP2) Shift Solenoid Valve S1
Shift Solenoid Valve SR
Shift Solenoid Valve SLU
Shift Solenoid Valve SL2 ATF Temperature
Sensor No. 2Integration Control and Panel
(Shift Position L Switch)
MIL
Shift Solenoid Valve SL1
Shift Solenoid
Valve SLT
ATF Temperature
Sensor No.1
Shift Solenoid Valve S2
Speed Sensor (NT)

AT Oil Temp Warning LightShift Lever
(O/D Main Switch)
4WD:
4WD Control ECU
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±519
713 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION

DIDIL±01
D14205
Shift Solenoid Valve S1
MIL
(Malfunction Indicator Lamp) S1
S2
SL1
SL2
SLT
SLU
SR
WShift Solenoid Valve S2
Shift Solenoid Valve SL1
Shift Solenoid Valve SL2
Shift Solenoid Valve SLT
Shift Solenoid Valve SLU
Shift Solenoid Valve SR
OILW
AT Oil Temp Warning Light ECM Crankshaft Position Sensor
Engine CoolantTemperature Sensor
Combination Meter
Stop Lamp Switch Assy
DLC3
(Data Link Connector 3)THW VTA1, 2
VC
SPD
STPTH01
TC Throttle Position Sensor
ATF (Automatic Transmission
Fluid) Temperature Sensor No. 1Mass Air Flow Meter
Accelerator Pedal Position SensorVPA
VPA2
Shift Lever
(O/D Main Switch)
Input Speed Sensor (NT)NT
Output Speed Sensor (SP2)SP2
TH02
ATF (Automatic Transmission
Fluid) Temperature Sensor No. 2Skid Control ECUNSW
Park/Neutral Position Switch
R, D, 3, 2
VG
NE
L
ODMSIntegration Control and Panel
(Shift Position L Switch)
L4



: 4WD4WD Control ECU
CAN DI±520
± DIAGNOSTICSAUTOMATIC TRANSMISSION
714 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DIAGRAM
The configuration of the electronic control system in the A750E/A750F automatic transmission is as shown
in the following chart.

DIDIP±01
12345678
9 10111213141516
D13649
DLC3:
CG
TC
D13654
DI±524
± DIAGNOSTICSAUTOMATIC TRANSMISSION
718 Author: Date:
2005 SEQUOIA (RM1146U)
BASIC INSPECTION
1. CHECK FLUID LEVEL
(a) Using SST, create a short±circuit between terminals TC
and CG of the DLC3.
SST 09843±18040
(b) Start the engine and run at idle.

The A/C switch must be turned off.

On models with active height control suspension &
adaptive variable suspension, turn the height con-
trol switch off.
(c) Slowly move the shift lever through all positions from P to
L, and move it back to the P position.
(d) Switch to the fluid temperature detection mode.
Move the shift lever from the N to the D position, or from
D to N, within 1.5 seconds. (Repeat this operation for 6 se-
conds or more.)
OK: The A/T OIL TEMP warning light comes on for 2
seconds and then goes off.
(e) Return the shift lever to the P position and disconnect ter-
minals TC and CG.
(f) Idle the engine to raise oil temperature.
(g) Lift up the vehicle immediately after the meter indicator
light (ATF temperature warning light) comes on.

The A/T OIL TEMP warning light indicates the ATF
temperature according to the following table.
ATF Temp.Less than optimized
temperatureOptimized temperatureMore than optimized
temperature
A/T OIL TEMP warning lightOFFONBlinking