2001 TOYOTA SEQUOIA instrument panel

H11622H12060B08604
Example:
CorrectWrong Clear Plastic Bag
R06952H12059B08605
Example:
± INTRODUCTIONFOR ALL OF VEHICLES
IN±15
15 Author: Date:
2005 SEQUOIA (RM1146U)
(g) CURTAIN SHIELD AIRBAG ASSEMBLY
(1) Always store a removed or new curtain shield air-
bag assembly in a clear plastic bag, and keep it in
a safe place.
NOTICE:
Protection bag is not reused.
CAUTION:
Never disassemble the curtain shield airbag assembly
(2) Never measure the resistance of the airbag squib
(This may cause the airbag to deploy, which is very
dangerous.).
(3) Grease should not be attached to the curtain shield
airbag assembly and the surface should not be
cleaned with any kind of detergents.
(4) Store the airbag assembly where the ambient tem-
perature remains below 93°C (200°F), without high
humidity and away from electrical noise.
(5) When using electric welding, first disconnect the air-
bag connector (yellow color and 2 pins) into the
instrument panel before starting work.
(6) When disposing of a vehicle or the curtain shield air-
bag assembly alone, the airbag should be deployed
using an SST before disposal (See page RS±73).
Perform the operation in a safe place away from
electrical noise.

IN±42
± INTRODUCTIONTERMS
42 Author: Date:
2005 SEQUOIA (RM1146U) H/B
Hatchback
H±FUSEHigh Current Fuse
HIHigh
HIDHigh Intensity Discharge (Head Lamp)
HSGHousing
HTHard Top
HWSHeated Windshield System
ICIntegrated Circuit
IDIIndirect Diesel Injection
IFSIndependent Front Suspension
IGIgnition
IIAIntegrated Ignition Assembly
INIntake (Manifold, Valve)
INTIntermittent
I/PInstrument Panel
IRSIndependent Rear Suspension
ISCIdle Speed Control
J/BJunction Block
J/CJunction Connector
KDKick±Down
LANLocal Area Network
LBLiftback
LCDLiquid Crystal Display
LEDLight Emitting Diode
LHLeft±Hand
LHDLeft±Hand Drive
L/H/WLength, Height, Width
LLCLong±Life Coolant
LNGLiquified Natural Gas
LOLow
LPGLiquified Petroleum Gas
LSDLimited Slip Differential
LSP & PVLoad Sensing Proportioning And Bypass Valve
LSPVLoad Sensing Proportioning Valve
MAPManifold Absolute Pressure
MAX.Maximum
MICMicrophone
MILMalfunction Indicator Lamp
MIN.Minimum
MG1Motor Generator No.1
MG2Motor Generator No.2
MPMultipurpose
MPIMultipoint Electronic Injection
MPXMultiplex Communication System
M/T, MTMManual Transmission (Transaxle)
MTMount
MTGMounting
NNeutral
NANatural Aspiration
NO.Number
O2SOxygen Sensor
O/DOverdrive

SS061±77
SS±46
± SERVICE SPECIFICATIONSSUPPLEMENTAL RESTRAINT SYSTEM
188 Author: Date:
2005 SEQUOIA (RM1146U)
SUPPLEMENTAL RESTRAINT SYSTEM
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Steering wheel set nut5051037
Steering wheel pad set screw (Torx screw)8.89078 in.´lbf
Front passenger airbag assembly x Instrument panel5.05144 in.´lbf
Front passenger airbag assembly x Instrument panel reinforcement2020415
Front seat x Body3737727
Front seat inner belt x Front seat4142831
Seatback cover x Seatback frame5.55649 in.´lbf
Armrest x Seatback frame3737727
Cutain shield airbag assembly x Body9.81007
Airbag senaor assembly x Body17.517913
Front airbag sensor x Body17.517913
Side airbag sensor assembly x Body17.517913
Curtain shield airbag sensor assembly x Body17.517913
Seat position sensor assembly x Body8.08271 in.´lbf

± SERVICE SPECIFICATIONSBODY
SS±49
191 Author: Date:
2005 SEQUOIA (RM1146U) Power window regulator x Door panel
5.55649 in.´lbf
Back door lock x Door panel8.08271 in.´lbf
FRONT WIPER AND WASHER±±±
Wiper link x Body5.55649 in.´lbf
Wiper motor x Wiper link5.55649 in.´lbf
Wiper arm x Wiper link2020415
REAR WIPER AND WASHER±±±
Rear wiper motor x Body5.55649 in.´lbf
Wiper arm x Rear wiper motor5.55649 in.´lbf
BODY OUTSIDE MOULDING±±±
Rear bumper cover x Rear bumper extension5.05043 in.´lbf
WINDSHIELD±±±
Inner rear view mirror set torx screw2.52522 in.´lbf
SLIDING ROOF±±±
Sliding roof housing x Body5.55649 in.´lbf
INSTRUMENT PANEL±±±
Front passenger airbag assembly x Instrument panel5.05144 in.´lbf
Front passenger airbag assembly x Instrument panel reinforcement2020415
Steering wheel x Steering wheel pad8.89078 in.´lbf
Box panel sub±assembly x Floor panel4040830
FRONT SEAT (Power Adjuster Type)±±±
w/ Side airbag:
Seatback cover bracket x Seat frame assembly5.55649 in.´lbf
Armrest x Seat frame assembly3738027
Front seat x Body3738027
FRONT SEAT (Manual Adjuster Type)±±±
w/ Side airbag:
Seatback cover bracket x Seat frame assembly5.55649 in.´lbf
Armrest x Seat frame assembly3738027
Front seat x Body3738027
REAR NO.1 SEAT (Separate Type)±±±
Rear seat cushion hinge x Body3738027
LH rear seat lock x Seat cushion frame4344032
Rear seat reclining adjuster x Seat cushion frame4344032
Rear seat reclining adjuster x Seatback frame4344032
RH rear seat lock x Seat cushion frame6465347
REAR NO. 1 SEAT (Split Type LH)±±±
Rear seat cushion hinge x Body4344032
Rear No. 1 seat outer adjuster x Seat cushion frame4344032
Rear No. 1 seat outer adjuster x Seatback frame4344032
Rear No. 1 seat inner adjuster x Seat cushion frame4344032
Rear No. 1 seat inner adjuster x Seatback frame4243031
Rear seat shoulder belt guide x Seatback frame3738027
REAR NO.1 SEAT (Split Type RH)±±±
Rear seat cushion hinge x Body3738027
Rear seat lock x Seat cushion frame4344032

DID7X±01
FI0534
D13872
Hand±Held Tester
DLC3
DI±40
± DIAGNOSTICSENGINE
234 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSIS SYSTEM
1. Description

When troubleshooting On±Board Diagnostic (OBD ll) ve-
hicles, the vehicle must be connected to the hand±held
tester. Various data output from the vehicle's ECM can
then be read.

OBD ll regulations require that the vehicle's on±board
computer illuminates the Malfunction Indicator Light (MIL)
on the instrument panel when the computer detects a
malfunction in: 1) the emission control system/compo-
nents, or 2) the powertrain control components (which af-
fect vehicle emissions), or 3) the computer. In addition,
the applicable Diagnostic Trouble Codes (DTCs) pre-
scribed by SAE J2012 are recorded in the ECM memory
(See page DI±58).
If the malfunction does not reoccur in 3 consecutive trips, the
MIL goes off automatically but the DTCs remain recorded in the
ECM memory.
To check the DTC, connect the hand±held tester or OBD II scan
tool to the Data Link Connector 3 (DLC3) of the vehicle. The
hand±held tester or OBD II scan tool also enables you to erase
the DTC and check the freeze frame data and various forms of
engine data (See the instruction manual for the hand±held tes-
ter). The DTC includes SAE controlled codes and manufacturer
controlled codes. SAE controlled codes must be set according
to the SAE, while manufacturer controlled codes can be set by
a manufacturer with certain restrictions (See the DTC chart on
page DI±58).
2. NORMAL MODE AND CHECK MODE
The diagnosis system operates in ºnormal modeº during normal
vehicle use. In ºnormal modeº, 2 trip detection logic* is used to
ensure accurate detection of malfunctions. A ºcheck modeº is
also available to technicians as an option. In ºcheck modeº, 1
trip detection logic is used for simulating malfunction symptoms
and increasing the system's ability to detect malfunctions, in-
cluding intermittent malfunctions (See page DI±11).
3. 2±TRIP DETECTION LOGIC
When a malfunction is first detected, the malfunction is tempo-
rarily stored in the ECM memory. This is known as 1st trip detec-
tion. If the ignition switch is turned OFF and then ON again, and
the same malfunction is detected again, the MIL will illuminate.
This is known as 2nd trip detection.

A23553
G±R
1 28
A 6
BECM
AM2
W±B6
32
15 3
2 121
3 2B IA1
J5
J/CL±O
I18
Ignition SW
3
7
F10
Fusible Link BlockB±R
BI530
10 26 4
12
2
114
68
1 41
5 3L±B
AM2
52HE6
2D
2F 1J1C2F
IA4
E4
E4 IG4
IA4 2H
2H 2C 1C
1JFPR
FC
MREL B±O5
J44
J45J/C E
L
BB1G±RG±REngine Room J/B
4
2F
5V V V
IL2
25
G±O G±O
B
IG2
W±B
W±BA
ED 5 4G±RIG1
B±WB±W
Instrument Panel J/B
F9
Fuel Pump
Resister
Battery2C
W±R W±R5
6
EFI No.15
C/OPN Relay Fuel Pump
Relay
EFI Relay F19
Fuel Pump
± DIAGNOSTICSENGINE
DI±181
375 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
HINT:
This diagnostic chart is based on premise that engine is started. If the engine is not started, proceed to prob-
lem symptoms table on DI±33.

A15466A19380
Battery I18
Ignition SW
1
#80 #60 #40#20
#70#50ECM
#30 #10
6
2
I10 Injector No.2
I12 Injector No.4
I13 Injector No.5
I14 Injector No.6
I15 Injector No.7
I16 Injector No.8
7
1
2
12
1
2 1
2
1
2
2
2
2 3 2
5
7 4
I9 Injector No.1
1C
2D1
B
F10
Fusible Link BlockIGN2
Engine Room J/B
54
B2C1 1C
1J 1D 2
3
W±R6
AM2Instrument Panel J/B
W±R3
B±R
1
1
1
I11 Injector No.3
IG413
E8 E6
E6
E8 E6 E6
E6 E6
R±W B±R
B±R
B±R
B±R
B±R
B±R
B±RY R±B
L±R W
L G R
B±R B±R B±R
5
IG2
AM2
B±R
B±R
B±R
B±R
B±R
DI±190
± DIAGNOSTICSENGINE
384 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
Refer to DTC P0351 on page DI±221 for the wiring diagram of the ignition system.
CONFIRMATION DRIVING PATTERN
(a) Connect the hand±held tester to the DLC3.
(b) Record DTC and the freeze frame data.
(c) Use the hand±held tester to set the check mode (See page DI±44).
(d) Read the value on the misfire counter for each cylinder when idling. If the value is displayed on the
misfire counter, skip the following procedure of confirmation driving.
(e) Drive the vehicle several times with the engine speed, load and surrounding range shown as ENGINE
SPD, CALC LOAD in the freeze frame data or MISFIRE RPM, MISFIRE LOAD in the DATA LIST.
If you have no hand±held tester, turn the ignition switch OFF after the symptom is simulated once. Then re-
peat the simulation process again.

A15470A19381
I8 Ignition Coil with Igniter No. 8
B±W
BR23
Ignition Coil with Igniter No. 7 I7
4
1
B±R
B±RECM
24
E8IGF1
IGF2
IGT8 E8
25
12E8
IGT7 9
E8
IGT6
11E8
15 E8 IGT5
E8
8IGT4
IGT3
E814
IGT2 13
E8
E8 10
IGT1
I18 Ignition SW
W±R IG2
AM25 1C2
1C3 IGN2 Instrument Panel J/B
2
1D
7 B±R 5
IG4 B±R
W±R
Engine Room J/B
2C 1
2DAM2 1
2
B
BatteryF10
Fusible Link Block4 1 2
N1 Noise Filter No. 1
B±R
1 3B±R4
BR
EC
2
I1 Ignition Coil with Igniter No. 1
B±R
I2 Ignition Coil with Igniter No. 2
1 3
4 2
B±W
BRB±R
I3 Ignition Coil with Igniter No. 3
BRBR
B±R B±R
B±R
B±R
B±R
B±R B±RB±R
3B±R1
4 2
B±W
I4 Ignition Coil with Igniter No. 4
413
2
I5 Ignition Coil with Igniter No. 5B±W
I6 Ignition Coil with Igniter No. 6
1 3
2
4
13
2
41 4 23
BR
B±W
G±R
P±L
G±W
R±W
G±B
LG±B
B±L
B±R
LG
BR
BR
BR
1J
BR
B±R
B±R
B±R
B±R
6
B±R BR
BR BRBRBR BR BR B±R
B±R
B±R
B
± DIAGNOSTICSENGINE
DI±225
419 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM