2001 TOYOTA SEQUOIA radiator

B02389
B02390
HEAT METHOD: When the problem seems to occur when the suspect area is heated. 2
NOTICE:3 WATER SPRINKLING METHOD:
(1)
(2)
4 OTHER: When a malfunction seems to occur when electrical load is excessive.When the malfunction seems to occur on a rainy day or in a
high±humidity condition. Heat the component that is the likely cause of the malfunction
with a hair dryer or similar object. Check to see if the malfunction
occurs.
Sprinkle water onto the vehicle and check to see if the malfunc-
tion occurs.
Turn on all electrical loads including the heater blower, head
lights, rear window defogger, etc. and check to see if the mal-
function occurs.ON HINT:
If a vehicle is subject to water leakage, the leaked water may
contaminate the ECU. When testing a vehicle with a water leak-
age problem, special caution must be taken.
Malfunc-
tion
Do not heat to more than 60 °C (140 °F). (Temperature
is limited not to damage the components.)
Do not apply heat directly to parts in the ECU. (1)
(2)
Never sprinkle water directly into the engine compart-
ment, but indirectly change the temperature and hu-
midity by applying water spray onto the radiator front
surface.
Never apply water directly onto the electronic compo-
nents. NOTICE: IN±30
± INTRODUCTIONHOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMS
30 Author: Date:
2005 SEQUOIA (RM1146U)

MA003±50
MA±4
± MAINTENANCEUNDER HOOD
51 Author: Date:
2005 SEQUOIA (RM1146U)
UNDER HOOD
GENERAL MAINTENANCE
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every service item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.

Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. WINDSHIELD WASHER FLUID
Check that there is sufficient fluid in the tank.
3. ENGINE COOLANT LEVEL
Check that the coolant level is between the FULL and LOW lines on the see±through reservoir.
4. RADIATOR AND HOSES
(a) Check that the front of the radiator is clean and not blocked with leaves, dirt or bugs.
(2UZ±FE engine: See page CO±14)
(b) Check the hoses for cracks, kinks, rot or loose connections.
5. BATTERY ELECTROLYTE LEVEL
Check that the electrolyte level of all battery cells is between the upper and lower level lines on the case.
6. BRAKE AND CLUTCH FLUID LEVELS
Check that the brake and clutch fluid levels are near the upper level line on the see±through reservoirs.
7. ENGINE DRIVE BELTS
Check all drive belts for fraying, cracks, wear or oiliness.
8. ENGINE OIL LEVEL
Check the level on the dipstick with the engine turned off.
9. POWER STEERING FLUID LEVEL
(a) Check the level on the dipstick.
(b) The level should be in the HOT or COLD range depending on the fluid temperature.
10. AUTOMATIC TRANSMISSION FLUID LEVEL
(a) Park the vehicle on a level surface.
(b) With the engine idling and the parking brake applied, shift the selector into all positions from the P to
L, and then shift into the P position.
(c) Pull out the dipstick and wipe off the fluid with a clean rag. Re±insert the dipstick and check that the
fluid level is in the HOT range.
(d) Do this check with the fluid at normal driving temperature (70 ± 80°C, 158 ± 176°F).
HINT:
Wait until the engine cools down (approx. 30 min.) before checking the fluid level after extended driving at
high speeds, in hot weather, in heavy traffic or pulling a trailer.
11. EXHAUST SYSTEM
(a) Visually inspect for cracks, holes or loose supports.
(b) If any change in the sound of the exhaust or smell of the exhaust fumes is noticed, find the cause and
correct.

PP1AQ±04
± PREPARATIONCOOLING
PP±15
73 Author: Date:
2005 SEQUOIA (RM1146U)
COOLING
EQUIPMENT
HeaterThermostat
Radiator cap tester
ThermometerThermostat
Torque wrench

SS0OR±13
SS±8
± SERVICE SPECIFICATIONSENGINE MECHANICAL
150 Author: Date:
2005 SEQUOIA (RM1146U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Fan shroud x Radiator assembly5.55043 in.´lbf
Radiator bracket x Radiator assembly2020015
A/C Compressor x Cylinder block4950036
Generator x Generator bracket3940029
No.1 idler pulley, No.2 idler pulley x Cylinder Block34.535025
Camshaft timing pulley x Camshaft timing tube8.18372 in.´lbf
Drive belt tensioner x Cylinder block1616012
Timing belt tensioner x Oil pump2627019
Crankshaft pulley x Crankshaft2452,500181
Fan bracket x Cylinder block 12 mm head
14 mm head16
32160
33012
24
No.2 timing belt cover x Cylinder block1616012
No.3 timing belt cover x Cylinder block, cylinder head7.58066 in.´lbf
Drive belt idler pulley x Fan bracket3940029
Fluid coupling x Fan bracket2929621
Exhaust manifold x Cylinder head4445033
Cylinder head x Cylinder block 1st
2nd
3rd40
Turn 90°
Turn 90°408
Turn 90°
Turn 90°30
Turn 90°
Turn 90°
Camshaft bearing cap x Cylinder head Bolt A
Others7.5
1680
16066 in.´lbf
12
Cylinder head cover x Cylinder head6.06053 in.´lbf
Engine hanger x Cylinder head3738027
Front water bypass joint, Rear water bypass joint x Cylinder head1818513
Intake manifold x Cylinder head1818513
Timing belt rear plate x Cylinder head7.58066 in.´lbf
Drive plate x Crankshaft 1st
2nd49
Turn 90°500
Turn 90°36
Turn 90°
Transmission x Cylinder block7273053
Transmission x No.1 oil pan3738027
Drive plate x Torque converter clutch4849035
Flywheel housing under cover x Transmission1818513
Engine rear mounting bracket x Transmission6566348
Frame crossmember x Rear engine mounting insulator Bolt A
Bolt B18
72183
73013
53
Frame bracket x Engine mounting bracket3838828
PS pump x Cylinder head6263246
Main bearing cap x Cylinder block 1st
2nd27
Turn 90°275
Turn 90°20
Turn 90°
Connecting rod cap x Connecting rod 1st
2nd24.5
Turn 90°250
Turn 90°18
Turn 90°
Rear oil seal retainer x Cylinder block8.08071 in.´lbf
Engine coolant drain union x Cylinder block4950036
Engine mounting bracket x Cylinder block3637027
Water bypass pipe x Cylinder block1818513

SS0O9±05
SS±14
± SERVICE SPECIFICATIONSCOOLING
156 Author: Date:
2005 SEQUOIA (RM1146U)
COOLING
SERVICE DATA
ThermostatValve opening temperature
Valve lift at 95°C (203°F)80 to 84°C (176 to 183°F)
10 mm (0.39 in.) or more
Radiator capRelief valve opening pressure Standard
Minimum74 to 103 kPa (0.75 to 1.05 kgf/cm2, 10.7 to 14.9 psi)
59 kPa (0.6 kgf/cm2, 8.6 psi)

SS0OA±04
± SERVICE SPECIFICATIONSCOOLING
SS±15
157 Author: Date:
2005 SEQUOIA (RM1146U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Drain plug x Union on cylinder block12.71309
Fan x Fluid coupling8.58575 in.´lbf
Water pump x Cylinder block Bolt
Stud bolt and nut21
18215
18515
13
Water inlet housing x Water pump1818513
Water inlet x Water inlet housing1919514
Radiator x Radiator support12.71309
No.1 fan shroud x Radiator55044 in.´lbf
Radiator mounting bolt121209

SS0O4±05
SS±52
± SERVICE SPECIFICATIONSAIR CONDITIONING
194 Author: Date:
2005 SEQUOIA (RM1146U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
REFRIGERANT LINE
Receiver x Liquid tube5.45548 in.´lbf
Condenser x Discharge hose5.45548 in.´lbf
Condenser x Liquid tube5.45548 in.´lbf
Compressor x Discharge hose101007
Compressor x Suction hose101007
Liquid and suction tube (Nut)5.45548 in.´lbf
Liquid and suction tube x Rear A/C unit5.45548 in.´lbf
COOLING UNIT
Evaporator x Expansion valve x Liquid and suction tube3.53631 in.´lbf
REAR A/C UNIT
Tube and accessory x Evaporator5.45531 in.´lbf
Tube and accessory x Expansion valve2223516
Expansion valve x Liquid tube1313510
COMPRESSOR AND MAGNETIC CLUTCH
Compressor x Engine (Bolt)4748035
Compressor x Bracket x Engine (Nut)2525518
Pressure plate x Rotor x Compressor1818412.3
PRESSURE SWITCH
Pressure switch x Liquid tube101007
WATER TEMPERATURE SWITCH
Water temperature switch x Radiator7.47565 in.´lbf

± DIAGNOSTICSENGINE
DI±141
335 Author: Date:
2005 SEQUOIA (RM1146U)
2 Inspect thermostat (See page CO±12).
CHECK:
Check the valve opening temperature of the thermostat.
OK:
Valve opening temperature is 80 to 84C (176 to 183F)
HINT:
Also check that the valve is completely closed under opening temperature as above.
NG Replace thermostat (See page CO±11).
OK
3 Check cooling system.
CHECK:
Check that there is detect in the cooling system which causes overcool, such as abnormal radiator fan opera-
tion, modified cooling system and so on.
NG Repair or replace cooling system.
OK
Replace engine coolant temperature sensor.