MA001±42
± MAINTENANCEOUTSIDE VEHICLE
MA±1
48 Author: Date:
2005 SEQUOIA (RM1146U)
OUTSIDE VEHICLE
GENERAL MAINTENANCE
The owners are responsible for these maintenance and inspection items.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES
Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.
Every service item in the periodic maintenance schedule must be performed.
Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).
Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.
Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. TIRES
(a) Check the pressure with a gauge.
If necessary, adjust.
(b) Check for cuts, damage or excessive wear.
3. WHEEL NUTS
When checking the tires, check the nuts for looseness or for missing.
If necessary, tighten them.
4. TIRE ROTATION (See page SA±3)
Check the owner's manual supplement in which the maintenance schedule is shown.
5. WINDSHIELD WIPER BLADES
Check for wear or cracks whenever they do not wipe clean.
If necessary, replace.
6. FLUID LEAKS
(a) Check underneath for leaking fuel, oil, water or other fluid.
(b) If you smell gasoline fumes or notice any leak, find the cause and correct.
7. DOORS AND ENGINE HOOD
(a) Check that all doors and the tailgate operate smoothly, and that all latches lock securely.
(b) Check that the engine hood secondary latch secures the hood from opening when the primary latch
is released.
BO462±01
H02485
Wiper Link
Cowl Panel
H09483
AB
C
C BO±38
± BODYFRONT WIPER AND WASHER
3591 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
1. INSTALL WASHER NOZZLES
2. INSTALL WIPER LINK
Install the wiper link through the service hole, then torque the
6 bolts.
Torque: 5.5 N´m (56 kgf´cm, 49 in.´lbf)
3. INSTALL WIPER MOTOR
(a) Install the wiper motor to the wiper link.
HINT:
When installing the wiper motor, connect the claw of wiper link
to the cowl panel shown in the illustration.
(b) Torque the 4 bolts.
Torque: 5.5 N´m (56 kgf´cm, 49 in.´lbf)
(c) Connect the connector.
4. INSTALL HOOD TO COWL TOP SEAL
Install the hood to cowl top seal to the cowl top ventilator louver.
5. INSTALL COWL TOP VENTILATOR LOUVER
Install the cowl top ventilator louver with the 8 screws and 6
clips.
6. INSTALL WIPER ARMS
(a) Operate the wiper once and turn the wiper switch OFF.
(b) Install the wiper arms and tighten the nuts by hand.
(c) Adjust the installation positions of the wiper arms to the
positions shown in the illustration.
A: Approx. 25.4 mm (1.000 in)
B: Approx. 40.0 mm (1.574 in)
HINT:
When installing the wiper arms, make sure that the tips of the
blades are not beyond the ceramic edge as indicated ºCº part
in the illustration.
(d) Torque the 2 nuts.
Torque: 20 N´m (205 kgf´cm, 15 ft´lbf)
(e) Install the 2 caps.
H00679
H03003
H16709
H09483
CAB
C BO±66
± BODYWINDSHIELD
3619 Author: Date:
2005 SEQUOIA (RM1146U)
(c) Correct insufficient or protruded adhesive agent using a
spatula.
HINT:
Apply the adhesive agent up to the windshield glass edge.
(d) Install a new windshield outside upper moulding to the
windshield glass before the adhesive agent hardens.
HINT:
Install the moulding, aligning the center of moulding with the
center of body.
(e) Remove any excessive adhesive agent before it hardens.
(f) Hold the glass and moulding in place securely with a pro-
tective tape or equivalent until the adhesive hardens.
NOTICE:
Take care not to drive the vehicle during the time described
in the table below.
TemperatureMinimum time prior to driving the vehicle
35°C (95 °F)1.5 hours
20°C (68 °F)5 hours
5°C (41 °F)24 hours
12. INSTALL WINDSHIELD OUTSIDE MOULDINGS
13. INSPECT FOR LEAK AND REPAIR
NOTICE:
Contact a leak test after the hardening time has elapsed.
14. INSTALL ROOF SIDE RAIL WEATHERSTRIP
Attach the upper edge of the weatherstrip to body flange. Tap
on the weatherstrip by hand.
15. INSTALL COWL TOP VENTILATOR LOUVER
16. INSTALL WIPER ARMS
(a) Operate the wipers once and turn the wiper switch OFF.
(b) Install the wiper arms and tighten the nuts by hand.
(c) Adjust the installation positions of the wiper arms to posi-
tions shown in the illustration.
A: Approx. 25.4 mm (1.000 in.)
B: Approx. 40.0 mm (1.575 in.)
HINT:
When installing the wiper arms, make sure that the tips of the
blades are not beyond the ceramic edge as indicated ºCº part
in the illustration.
