2001 TOYOTA SEQUOIA brake rotor

MA0055
MA014±06
MA±6
± MAINTENANCEBRAKE
53 Author: Date:
2005 SEQUOIA (RM1146U)
BRAKE
INSPECTION
1. INSPECT BRAKE LINE PIPES AND BOOTS
HINT:
Inspect in a well±lighted area. Inspect the entire circumference
and length of the brake hoses using a mirror as required. Turn
the front wheels fully right or left before inspecting the front
brake.
(a) Check all brake lines and hoses for:

Damage

Wear

Deformation

Cracks

Corrosion

Leaks

Bends

Twists
(b) Check all clamps for tightness and connections for leak-
age.
(c) Check that the hoses and lines are clear of sharp edges,
moving parts and the exhaust system.
(d) Check that the lines installed in grommets pass through
the center of the grommets.
2. INSPECT FRONT AND REAR BRAKE PADS AND
DISCS
(Front pads: See page BR±25)
(Rear pads: See page BR±34)
HINT:
If a squealing or scraping noise occurs from the brake during
driving, check the pad wear indicator.
If there are traces of the indicator contacting the disc rotor, the
disc pad should be replaced.

D14162
Clutch Drum
(Timing Rotor)
Input Speed Sensor NT
(Transmission Revolution Sensor NT)Output Speed Sensor SP2
(Transmission Revolution Sensor SP2)
Parking Gear
(Timing Rotor)
D14148
GND
1 V/DIV
2 ms/DIV
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±591
785 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0717 Input Speed Sensor Circuit No Signal
CIRCUIT DESCRIPTION
This sensor detects the rotation speed of the turbine which shows the input revolution of transmission. By
comparing the input turbine speed signal (NT) with the counter gear speed sensor signal (SP2), the ECM
detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure ac-
cording to various conditions, thus, providing smooth gear shift.
DTC No.DTC Detection ConditionTrouble Area
P0717
All conditions below are detected for 5 secs. or more
(1±trip detection logic)
(a) Gear change is not performed
(b) Gear position: 4th or 5th
(c) T/M input shaft rpm: 300 rpm or less
(d) T/M output shaft rpm: 1,000 rpm or more
(e) Park/neutral position switch:

NSW input signal is OFF

R input signal is OFF

L input signal is OFF
(f) Shift solenoid valves, park/neutral position switch and ve-
hicle speed sensor are in normal operation

Open or short in speed sensor (NT) circuit

Speed sensor (NT)

ECM

Automatic transmission (clutch, brake or gear, etc.)
Reference (Using an oscilloscope):
Check the waveform between terminals NT+ and NT± of
the ECM connector.
Standard: Refer to the illustration.
TerminalNT+ ± NT±
Tool setting1V/DIV, 2ms/DIV
Vehicle conditionEngine idle speed (P or N position)
DIDJ8±01

D14162
Clutch Drum
(Timing Rotor)
Input Speed Sensor NT
(Transmission Revolution Sensor NT)Output Speed Sensor SP2
(Transmission Revolution Sensor SP2)
Parking Gear
(Timing Rotor)
C13480D14149
GND
2 V/DIV
20 ms/DIV
DI±596
± DIAGNOSTICSAUTOMATIC TRANSMISSION
790 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0722 Output Speed Sensor Circuit No Signal
CIRCUIT DESCRIPTION
The speed sensor SP2 detects the rotation speed of the transmission output shaft and sends signals to the
ECM. The ECM determines the vehicle speed based on these signals. An AC voltage is generated in the
speed sensor SP2 coil as the parking gear mounted on the rear planetary gear assy rotates, and this voltage
is sent to the ECM. The parking gear on the rear planetary gear is used as the timing rotor for this sensor.
The gear shift point and lock±up timing are controlled by the ECM based on the signals from this vehicle
speed sensor and the throttle position sensor signal.
DTC No.DTC Detection ConditionTrouble Area
P0722
All conditions below are detected 500 times or more continu-
ously (1±trip detection logic)
(a) No signal from speed sensor (SP2) is input to ECM while 4
pulses of No. 1 vehicle speed sensor signal are sent
(b) Vehicle speed is 9 km/h (6 mph) or more for at least 4 sec.
(c) Park/neutral position switch is OFF.
(d) Transfer position is except neutral (4WD).

Open or short in speed sensor (SP2) circuit

Speed sensor (SP2)

ECM

Automatic transmission (clutch, brake or gear, etc.)
Reference (Using an oscilloscope):
Check the waveform between terminals SP2+ and SP2±
of the ECM connector.
Standard: Refer to the illustration.
TerminalSP2+ ± SP2±
Tool setting2V/DIV, 20ms/DIV
Vehicle conditionVehicle speed 20 km/h (12 mph)
DIDJ9±01

DIDLV±01
F17996
Front Speed SensorABS & VSC Actuator
(w/ Skid Control ECU)Level Warning Switch
Rear Speed Sensor Rear Speed Sensor Rotor
Front Speed
Sensor Rotor
Parking Brake SwitchStop Light Switch
Center Diff. Lock Switch *1
TRAC OFF Switch *2
Steering Angle Sensor
DLC3Brake Inhibit RelayTranslate ECU
VSC BuzzerBrake Booster
(Including Active Brake Booster
Solenoid, Delta S Sensor and Boost-
er Pedal Switch)
Master Cylinder
Pressure Sensor
Front Speed Sensor Rotor
Front Speed Sensor
Yaw Rate Sensor
(Including Deceleration Sensor)
ABS Warning Light
VSC TRAC Warning light
VSC OFF Indicator Light *
1
TRAC OFF Indicator Light *2
BRAKE Warning Light
SLIP Indicator Light
*1: Only for 4WD
*2: Only for 2WDCenter Diff. Lock
Position Switch
DI±892
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1086 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION

DI93C±06
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±921
111 5 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSTIC TROUBLE CODE CHART
NOTICE:

When removing parts, turn the ignition switch OFF.

When replacing the master cylinder, yaw rate and deceleration sensors and/or the ECU, make
sure to perform master cylinder, yaw rate and deceleration sensors' zero point calibration (See
page DI±897).
HINT:

Using SST 09843±18040, connect terminals Tc and CG.

If no abnormality is found when inspecting parts, inspect the ECU.

If a trouble code is displayed during the DTC check, check the circuit listed for that code. For details
of each code, turn to the page referred to under the ºSee pageº for respective ºDTC No.º in the DTC
chart.
DTC chart of ABS system:
DTC No.
(See Page)Detection ItemTrouble Area
C0200/31*1
(DI±925)Right front wheel speed sensor signal malfunction
C0205/32*1
(DI±925)Left front wheel speed sensor signal malfunction
Right front, left front, right rear and left rear speed sensor

Each speed sensor circuit
C0210/33*1
(DI±925)Right rear wheel speed sensor signal malfunction

Each s eed sensor circuit

Speed sensor rotor

Skid control ECU
C0215/34*1
(DI±925)Left rear wheel speed sensor signal malfunction
C0226/21
(DI±932)Malfunction in ABS & VSC solenoid valves
ABS & VSC actuator

ABS & VSC solenoid circuit
C0278/11
(DI±934)Open or short circuit in ABS & VSC relay circuit

ABS & VSC solenoid relay

ABS & VSC solenoid relay circuit

ABS & VSC motor relay

ABS & VSC motor relay circuit
C1241/41
(DI±957)Low battery positive voltage or abnormally high battery positive
voltage

Battery

Charging system

Power source circuit (+BM, +BS)

Skid control ECU
C1244/44
(DI±951)Open or short circuit in deceleration sensor circuit
Yaw rate (deceleration) sensor

Yaw rate (deceleration) sensor circuit
C1247/47
(DI±960)Malfunction in delta S sensor

Delta S sensor

Delta S sensor circuit

Skid control ECU

Brake booster
C1249/49
(DI±963)Open circuit in stop light switch circuit

Stop light switch

Stop light switch circuit

Skid control ECU
C1251/51*1
(DI±966)
Pump motor is locked
Open circuit in pump motor circuit
ABS & VSC actuator
C1337/37
(DI±975)Some tires are different in size from the other tires
Tire size
Always ON
(DI±1016)Malfunction in skid control ECU

Battery

Charging system

Power source circuit

ABS warning light circuit

Skid control ECU

SA143±10
F14316
N´m (kgf´cm, ft´lbf) : Specified torque

Non±reusable part
64 (650, 47)
Brake CaliperHub Bolt
Cotter Pin
105 (1,100, 77)
8.0 (82, 71 in.´lbf)
Speed Sensor
Shock Absorber
135 (1,400, 100)
65 (663, 48)
123 (1,250, 90)
28 (285, 21)Steering Knuckle with Axle Hub
Disc
4WD:

Cotter Pin
235 (2,400, 173)
Lock Cap
Grease Cap
Grease Cap2WD:
4WD:

Oil Seal
Speed Sensor
Rotor
Dust Cover
Steering Knuckle
18 (185, 13)

Oil Seal
Bearing

Snap Ring
Axle Hub
Bearing Spacer4WD:
274 (2,800, 203)

Lock Nut 2WD:
± SUSPENSION AND AXLEFRONT AXLE HUB
SA±21
3017 Author: Date:
2005 SEQUOIA (RM1146U)
FRONT AXLE HUB
COMPONENTS

SA17R±04
F14272
122 (1,244, 90)

Oil Seal

O±ring
Parking Brake Assembly
Disc Brake Caliper

Bearing Retainer

Speed Sensor Rotor

Snap Ring

Bearing Retainer

Spring Washer
Backing PlateSerration Bolt

Hub Bolt
Oil Deflector

GasketAxle Shaft
N´m (kgf´cm, ft´lbf): Specified torque

Non±reusable partx6
105 (1,070, 77)
15.5 (158, 11)
Clip
Parking Brake Cable

Hub Bolt
8.0 (82, 71 in.´lbf)

Bearing Assembly SA±94
± SUSPENSION AND AXLEREAR AXLE SHAFT
3090 Author: Date:
2005 SEQUOIA (RM1146U)
REAR AXLE SHAFT
COMPONENTS