2006 LAND ROVER FRELANDER 2 Repair Manual

brake pads tire type fuel type set clock door lock transmission

Page 137 of 3229

LAND ROVER FRELANDER 2 2006 Repair Manual DT C
Description Possible Cause Action
U3003-62 Batt ery Vol tage - Si gnal
compare failure Res t raint s cont rol module
meas ured vol tage i s 2.5v
lower than bat tery
vol tage Refer to the el ect

Page 138 of 3229

LAND ROVER FRELANDER 2 2006 Repair Manual Publ is hed: 27-Apr-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Steering
Angle Sensor Module (SASM)
Des cript ion and Operat ion
• NOTE: If a cont rol module or component i

Publ is hed: 27-Apr-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Steering
Angle Sensor Module (SASM)
Des cript ion and Operat ion
• NOTE: If a cont rol module or component i s s uspect and the vehicl e remai ns under manufacturer warrant y, refer t o t heW arranty Pol icy and Procedures manual (s ect ion B1.2), or determine i f any pri or approval program is i n operat ion, beforet he replacement of a component.
• NOTE: Generic scan t ool s may not read the codes li st ed, or may read only 5-digi t codes . Match t he 5 digi ts from t he s cant ool t o t he fi rs t 5 di gi ts of the 7-digit code li s ted t o i dent ify the fault (the last 2 digi ts gi ve ext ra informati on read by themanufacturer-approved di agnos ti c s ys t em).
• NOTE: W hen performing volt age or res is t ance t est s , always use a digi tal mult imeter (DMM) accurat e t o t hree deci malplaces, and wi th an up-t o-date cal ibrat ion cert ificate. W hen tes ti ng res is t ance al ways take t he res is t ance of t he DMMleads i nt o account .
• NOTE: Check and recti fy bas ic faul ts before beginni ng diagnos t ic rout ines i nvol vi ng pinpoint t es t s.
• NOTE: Ins pect connect ors for s igns of water ingres s , and pins for damage and/or corros ion.
• NOTE: If DTCs are recorded and, aft er performi ng the pi npoi nt tes ts , a fault is not present , an int ermi tt ent concern maybe t he caus e. Always check for loose connect ions and corroded terminals .
Des cript ion And Operat ion
For a detail ed descripti on of the ant i lock cont rol s tabil it y s yst em, refer to the relevant Des cri pt ion and Operati on s ect ionin the workshop manual.For addit ional informat ion, refer t o: Anti -Lock Cont rol - St abi li ty As s is t (206-09C Anti -Lock Cont rol - St abi lit y As s is t,Des cript ion and Operat ion).
Steering Angle Sensor Module
DT CDescriptionPossible CauseAction
U0001-00High Speed CANCommunicati on BusGeneral Fai lureInformat ion No s ub typeinformat ion
Bus OffCarry out t he pinpoint t es t s as sociat ed to thi s DTCus ing the manufact urer approved di agnos ti c s yst em
U0140-00Lost Communi cat ion W it hCentral el ect ronic modul eGeneral Fai lureInformat ion No s ub typeinformat ion
Lost communicat ion wi thCJBCarry out t he pinpoint t es t s as sociat ed to thi s DTCus ing the manufact urer approved di agnos ti c s yst em
U0300-00Int ernal Control ModuleSoft ware Incompat ibi lit yGeneral Fai lureInformat ion No s ub typeinformat ion
CAN Bus faul tLoss of power t o moduleIncorrect componentins t al ledModule i nternal fai lure
Carry out CAN net work and power feed t es ts us ingmanufact urer approved di agnos t ic s yst em. Checkcorrect s t eering wheel rot ati on s ens or is ins tall ed.Ins tall a new s teeri ng wheel rotat ion s ens or asrequi red, refer to new module/componenti nst all at ion not e at t he top of t he DTC Index.
U3000-04Control Module GeneralFailure Informat ionSyst em Int ernal Fail ures
CAN Bus faul tLoss of power t o moduleIncorrect componentins t al ledModule i nternal fai lure
Carry out CAN net work and power feed t es ts us ingmanufact urer approved di agnos t ic s yst em. Checkcorrect s t eering wheel rot ati on s ens or is ins tall ed.Ins tall a new s teeri ng wheel rotat ion s ens or asrequi red, refer to new module/componenti nst all at ion not e at t he top of t he DTC Index.U3000-14Control Module GeneralElectrical Fai lures Ci rcuits hort t o ground or open
Loss of power t o moduleModule i nternal fai lureCarry out power feed t est s us ing manufact urerapproved diagnost ic sys tem. Ins tal l a new s teeringwheel rot ati on s ens or as required, refer t o newmodul e/component ins t al lat ion note at the t op oft he DTC Index.
U3000-1DControl Module GeneralElectrical Fai lures Ci rcuitcurrent out of range
Loss of power t o moduleModule i nternal fai lureCarry out power feed t est s us ing manufact urerapproved diagnost ic sys tem. Ins tal l a new s teeringwheel rot ati on s ens or as required, refer t o newmodul e/component ins t al lat ion note at the t op oft he DTC Index.
U3000-44Control Module Sys t emInt ernal Failures Datamemory fai lure
Module i nternal fai lureIns tall a new s teeri ng wheel rotat ion s ens or asrequi red, refer to new module/componenti nst all at ion not e at t he top of t he DTC Index.U3000-48Control Module Sys t emInt ernal FailuresSupervis ion s oft warefai lure
Module i nternal fai lureIns tall a new s teeri ng wheel rotat ion s ens or asrequi red, refer to new module/componenti nst all at ion not e at t he top of t he DTC Index.
U3000-49Control Module Sys t emInt ernal Failures Int ernalelectronic fai lure
Loss of power t o moduleModule i nternal fai lureCarry out power feed t est s us ing manufact urerapproved diagnost ic sys tem. Ins tal l a new s teeringwheel rot ati on s ens or as required, refer t o newmodul e/component ins t al lat ion note at the t op oft he DTC Index.
U3000-61Control Module Algori thmBas ed Fai lures Si gnalcalcul ati on fai lure
Steering wheel rot at ions ens or mi s-ali gnedModule i nternal fai lure
Check for correct i nst all at ion of s ens or. Ins t al l anew st eeri ng wheel rotat ion s ensor as requi red,refer t o new module/component ins tal lati on note att he t op of the DTC Index.

Page 139 of 3229

LAND ROVER FRELANDER 2 2006 Repair Manual DT CDescriptionPossible CauseAction
U3000-62Control Module Algori thmBas ed Fai lures Si gnalcompare failure
Steering wheel rot at ions ens or mi s-ali gnedModule i nternal fai lure
Check for correc

DT CDescriptionPossible CauseAction
U3000-62Control Module Algori thmBas ed Fai lures Si gnalcompare failure
Steering wheel rot at ions ens or mi s-ali gnedModule i nternal fai lure
Check for correct i nst all at ion of s ens or. Ins t al l anew st eeri ng wheel rotat ion s ensor as requi red,refer t o new module/component ins tal lati on note att he t op of the DTC Index.U3000-64Control Module Algori thmBas ed Fai lures Si gnalplaus ibil it y fai lure
Steering wheel rot at ions ens or mi s-ali gnedModule i nternal fai lure
Check for correct i nst all at ion of s ens or. Ins t al l anew st eeri ng wheel rotat ion s ensor as requi red,refer t o new module/component ins tal lati on note att he t op of the DTC Index.U3000-81Control Module Bus Signal/ Mes s age Fai lures Inval ids eri al dat a received
Loss of power t o moduleCAN Bus faul tModule i nternal fai lure
Carry out CAN net work and power feed t es ts us ingmanufact urer approved di agnos t ic s yst em. Ins t all anew st eeri ng wheel rotat ion s ensor as requi red,refer t o new module/component ins tal lati on note att he t op of the DTC Index.
U3000-87Control Module Bus Signal/ Mes s age Fai luresMi ss ing mess age
Loss of power t o moduleCAN Bus faul tMis s ing modul e
Carry out CAN net work and power feed t es ts us ingmanufact urer approved di agnos t ic s yst em. Check formis s ing modules on CAN network
U3000-92Control ModuleComponent Fail uresPerformance or incorrectoperati on
Steering wheel rot at ions ens or mi s-ali gnedModule i nternal fai lure
Check for correct i nst all at ion of s ens or. Ins t al l anew st eeri ng wheel rotat ion s ensor as requi red,refer t o new module/component ins tal lati on note att he t op of the DTC Index.U3003-62Batt ery Vol tage Al gorit hmBas ed Fai lures Si gnalcompare failure
Mis -match i n batt eryvolt age, of 2 volt s ormore, bet ween CJB ands teeri ng wheel rotat ions ens or module
Carry out t he pinpoint t es t s as sociat ed to thi s DTCus ing the manufact urer approved di agnos ti c s yst em

Page 140 of 3229

LAND ROVER FRELANDER 2 2006 Repair Manual Publ is hed: 28-Apr-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Satellite
Digital Audio Radio System Module (SARM)
Des cript ion and Operat ion
• NOTE: If a cont rol module o

Publ is hed: 28-Apr-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Satellite
Digital Audio Radio System Module (SARM)
Des cript ion and Operat ion
• NOTE: If a cont rol module or component i s s uspect and the vehicl e remai ns under ma nufacturer warrant y, refer t o t he
W arranty Pol icy and Procedures manual (s ect ion B1.2), or determine i f any pri or appr oval program is i n operat ion, before
t he replacement of a component.
• NOTE: Generic scan t ool s may not read the codes li st ed, or may read only 5-digi t c odes . Match t he 5 digi ts from t he s can
t ool t o t he fi rs t 5 di gi ts of the 7-digit code li s ted t o i dent ify the fault (the las t 2 digi ts gi ve ext ra informati on read by the
manufacturer-approved di agnos ti c s ys t em).
• NOTE: W hen performing volt age or res is t ance t est s , always use a digi tal mult imeter (DMM) accurat e t o t hree deci mal
places, and wi th an up-t o-date cal ibrat ion cert ificate. W hen tes ti ng res is t ance al wa ys take t he res is t ance of t he DMM
leads i nt o account .
• NOTE: Check and recti fy bas ic faul ts before beginni ng diagnos t ic rout ines i nvol vi n g pinpoint t es t s.
• NOTE: Ins pect connect ors for s igns of water ingres s , and pins for damage and/or co rros ion.
• NOTE: If DTCs are recorded and, aft er performi ng the pi npoi nt tes ts , a fault is no t present , an int ermi tt ent concern may
be t he caus e. Always check for loose connect ions and corroded terminals .
Des cript ion And Operat ion
For a detail ed descripti on of the sat elli te radio sys tem, refer t o t he rel evant Des c ript ion and Operat ion s ecti on in the
works hop manual .
For addit ional informat ion, refer t o: Audi o Sys tem (415-01 Informati on and Entertainment Sys tem, Des cript ion and
Operat ion).
Satellite Radio Module (SRM) DT C Description Possible Cause Action
B1A89-11 Satell it e
antenna SDARS ant enna ci rcuit - s hort t o
ground Refer t o el ect ri cal circui t di agrams and check SDARS ant enna
circui t for s hort t o ground
B1A89-12 Satell it e
antenna SDARS ant enna ci rcuit - s hort t o
power Refer t o el ect ri cal circui t di agrams and check SDARS ant enna
circui t for s hort t o power
B1A89-13 Satell it e
antenna SDARS ant enna ci rcuit - open
ci rcuit Refer t o el ect ri cal circui t di agrams and check SDARS ant enna
circui t for open circui t
U3000-04 Control
module Sys tem int ernal fai lure
Ins tall a new s at ell it e radi o module.
For addi ti onal i nformat ion, refer to: Sat el li te Radi o Tuner (415-01
Informati on and Entert ainment Syst em, Removal and Ins tall ati on).
U3000-4A Control
module Incorrect component ins t al led
Ins tall a new s at ell it e radi o module.
For addi ti onal i nformat ion, refer to: Sat el li te Radi o Tuner (415-01
Informati on and Entert ainment Syst em, Removal and Ins tall ati on).
or Re-confi gure t he s atell it e radi o module us i ng the manufact urer
approved diagnost ic sys tem
U3000-55 Control
module Incorrect Car Configurat ion Fi le
dat a received Check/up-date Car Configurat ion Fil e us ing manufact urer approved
di agnos ti c s ys t em
U3000-87 Control
module Mis s ing mes s age
Check CJB for DTCs and refer to DTC Index.
For addi ti onal i nformat ion, refer to: Communi cat ions Network (418-00 Module Communi cat ions Net work, Diagnosi s and Test ing).
Check informat ion and entertai nment modul e for Car Confi gurati on
Fi le and MOST net work DTCs and refer t o rel evant DTC Index.
Carry out MOST/CAN network tes t s usi ng t he manufact urer
approved diagnost ic sys tem
U3000-98 Control
module Component or sys tem over
temperat ure Check for addit ional DTCs and refer t o rel evant DTC Index.
Check/monit or sys t em for re-occurrence
U3003-62 Batt ery
volt age Mis -mat ch in bat t ery volt age, of
2 vol ts or more, between
sat elli te radio modul e and CJB Carry out pinpoint t est s as s ociat ed wi th t his DTC usi ng t he
manufact urer approved di agnos t ic s yst em

Page 141 of 3229

LAND ROVER FRELANDER 2 2006 Repair Manual Publi s hed: 05-May-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC:
Transmission Control Module (TCM)
Des cript ion and Operat ion
• NOTE: If a cont rol module or component i s

Publi s hed: 05-May-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC:
Transmission Control Module (TCM)
Des cript ion and Operat ion
• NOTE: If a cont rol module or component i s s uspect and the vehicl e remai ns under ma nufacturer warrant y, refer t o t he
W arranty Pol icy and Procedures manual (s ect ion B1.2), or determine i f any pri or appr oval program is i n operat ion, before
t he replacement of a component.
• NOTE: Generic scan t ool s may not read the codes li st ed, or may read only 5-digi t c odes . Match t he 5 digi ts from t he s can
t ool t o t he fi rs t 5 di gi ts of the 7-digit code li s ted t o i dent ify the fault (the las t 2 digi ts gi ve ext ra informati on read by the
manufacturer-approved di agnos ti c s ys t em).
• NOTE: W hen performing volt age or res is t ance t est s , always use a digi tal mult imeter (DMM) accurat e t o t hree deci mal
places, and wi th an up-t o-date cal ibrat ion cert ificate. W hen tes ti ng res is t ance al wa ys take t he res is t ance of t he DMM
leads i nt o account .
• NOTE: Check and recti fy bas ic faul ts before beginni ng diagnos t ic rout ines i nvol vi n g pinpoint t es t s.
• NOTE: Ins pect connect ors for s igns of water ingres s , and pins for damage and/or co rros ion.
• NOTE: If DTCs are recorded and, aft er performi ng the pi npoi nt tes ts , a fault is no t present , an int ermi tt ent concern may
be t he caus e. Always check for loose connect ions and corroded terminals .
Des cript ion And Operat ion
For a detail ed descripti on of the trans mi ss i on cont rol s ys t em, refer to t he relevant Des cript ion and O perati on sect ion i n the
works hop manual . For addit ional informat ion, refer t o: Trans mis s ion Des cript ion (307-01 Aut omati c
Trans mis s ion/Transaxle, Des cript ion and Operat ion).
Transmission control module (TCM) DT C Description Possible Cause Action
P0218-68 Trans mis s ion flui d
overtemperat ure condit ion Transmis si on fluid level l ow Transmis si on fluid
cooler/hos es are
obs t ructed/damaged/blocked. Mechanical fault i n the
trans mi ss i on Check t he transmis s ion fluid level and
condit ion. Check t he t rans mis s ion flui d cool er
/hos es for s igns of obst ruct ion/damage
/blockage. Recti fy as necess ary. Refer t o t he
warrant y poli cy and procedures manual if t he
trans mi s si on is sus pect .
P0500-00 Vehi cle s peed s ens or A
(out put s haft s peed
s ens or) Vehi cl e s peed sens or A
ci rcuit : short ci rcuit t o ground Vehi cl e s peed sens or A
ci rcuit : open ci rcuit Vehi cl e s peed sens or A faul t Check t he vehi cl e s peed sens or A and circui ts .
Refer to the el ect ri cal guides . Rect ify as
neces sary.
P056-100 Sys t em volt age unst able Bat tery faul t Chargi ng s yst em fault Check t he batt ery and charging sys tems . Refer
to the el ect ri cal guides. Recti fy as neces sary.
P0562-00 Sys t em volt age low Bat tery faul t Chargi ng s yst em fault
P0601-00
Int ernal cont rol module
memory checksum error Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Reconfi gure t he module us ing the approved
di agnos t ic s yst em.
P0603-00 Int ernal cont rol module
keep al ive memory (KAM)
error Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Refer to the warrant y pol icy and procedures
manual i f the TCM is s us pect .
P0604-00 Int ernal cont rol module
random acces s memory
(RAM) error Int ernal t rans mi ss i on cont rol
modul e (TCM) fault P0605-00
Int ernal cont rol module
read only memory (ROM)
error Int ernal t rans mi ss i on cont rol
modul e (TCM) fault P0614-00
Engi ne cont rol module
(ECM)/t rans mi ss i on cont rol
module (TCM) incompati bl e Incorrect s oft ware i n TCM Reconfi gure t he module us ing the approved
di agnos t ic s yst em.
P062F-00 Int ernal cont rol module
electrically eras abl e
programmabl e read onl y
memory (EEPROM) error Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Refer to the warrant y pol icy and procedures
manual i f the TCM is s us pect .
P0705-00 Trans mis s ion range sens or
A circui t (PRNDL i nput ) Incorrect adjus tment of t he
gear s elector lever cabl e Incorrect adjus tment of t he
gear posi ti on s ens or Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Check t he adjus tment of t he gear s elector l ever
cable and sens or.
For addit ional informati on, refer t o: Sel ect or Lever Cabl e Adjus t ment (307-05 Aut omati c
Transmis s ion/Trans axle External Cont rols ,
General Procedures ).
Refer to the warrant y pol icy and procedures
manual i f the TCM is s us pect .
P0706-00 Trans mis s ion range sens or
A circui t range/performance Incorrect adjus tment of t he
gear s elector lever cabl e Incorrect adjus tment of t he
gear posi ti on s ens or Int ernal t rans mi ss i on cont rol Check t he adjus tment of t he gear s elector l ever
cable.
For addit ional informati on, refer t o: Sel ect or Lever Cabl e Adjus t ment (307-05 Aut omati c
Transmis s ion/Trans axle External Cont rols ,

Page 142 of 3229

LAND ROVER FRELANDER 2 2006 Repair Manual DT C
Description Possible Cause Action
modul e (TCM) fault General Procedures ).
Cal ibrat e t he gear pos it ion sens or us i ng the
approved di agnos ti c s ys t em. Refer to the
warrant y poli cy

DT C
Description Possible Cause Action
modul e (TCM) fault General Procedures ).
Cal ibrat e t he gear pos it ion sens or us i ng the
approved di agnos ti c s ys t em. Refer to the
warrant y poli cy and procedures manual if t he
TCM is sus pect .
P0709-00
Trans mis s ion range sens or
A circui t int ermi tt ent Incorrect adjus tment of t he
gear s elector lever cabl e Incorrect adjus tment of t he
gear posi ti on s ens or Int ernal t rans mi ss i on cont rol
modul e (TCM) fault P0711-00
Trans mis s ion flui d
temperature s ens or A
circuit range/performance Transmis si on fluid
temperat ure s ens or ci rcuit :
hi gh res is t ance i n t ermi nal s Transmis si on fluid
temperat ure s ens or fault Check t he transmis s ion fluid temperat ure
sens or and ci rcuit s. Refer to t he elect rical
gui des . Recti fy as necess ary.
P0712-00 Trans mis s ion flui d
temperature s ens or A
circuit l ow Transmis si on fluid
temperat ure s ens or ci rcuit :
short ci rcuit t o ground Transmis si on fluid
temperat ure s ens or ci rcuit :
open circui t P0713-00
Trans mis s ion flui d
temperature s ens or A
circuit hi gh Transmis si on fluid
temperat ure s ens or ci rcuit :
short ci rcuit t o power P0715-00
Turbine/Input shaft speed
(ISS) s ens or A circui t Transmis si on ISS ci rcuit :
short ci rcuit t o power Check t he transmis s ion ISS s ens or and circuit s .
Refer to the el ect ri cal guides . Ins tal l a new ISS
sens or as neces sary. For addit ional i nformati on,
refer t o: (307-01 Aut omati c
Transmis s ion/Trans axle)
Input Shaft Speed (ISS) Sensor - I6 3.2L Pet rol (Removal and Ins t al lat ion),
Input Shaft Speed (ISS) Sensor - TD4 2.2L Di esel (Removal and Ins t allat ion).
P0716-00
Turbine/Input shaft speed
(ISS) s ens or A circui t
range/performance Transmis si on ISS s ens or
ci rcuit : high res i st ance in
terminals Transmis si on ISS s ens or fault
P0718-00
Turbine/input shaft speed
(ISS) s ens or A circui t
int ermi tt ent Transmis si on ISS s ens or
ci rcuit : int ermi tt ent hi gh
res is tance in terminals Transmis si on ISS s ens or fault
P0720-00
Output s haft s peed (OSS)
s ens or circuit (vehi cle
s peed s ens or A circuit ) OSS s ens or ci rcuit : s hort
ci rcuit t o power Check t he transmis s ion OSS s ens or and circui ts .
Refer to the el ect ri cal guides . Rect ify as
neces sary.
P0721-00 Output s haft s peed (OSS)
s ens or circuit (vehi cle
s peed s ens or A circuit )
range/performance The wheel radi us does not
agree wit h t he wheel radius
programmed in t he car
confi gurati on fi le OSS s ens or not ins tall ed
correctl y OSS s ens or ci rcuit : high
res is tance in terminals OSS s ens or fault Check t hat t he correct wheels and ti res are
ins tall ed. Check t he transmis si on OSS s ensor
for correct ins t al lat ion. Check t he OSS s ensor
and ci rcuit s. Refer to t he elect rical guides.
Rect ify as neces s ary.
P0722-00 Output s haft s peed (OSS)
s ens or circuit (vehi cle
s peed s ens or A circuit ) no
s ignal OSS s ens or ci rcuit : high
res is tance in terminals OSS s ens or ci rcuit : open
ci rcuit OSS s ens or ci rcuit : s hort
ci rcuit t o ground OSS s ens or fault
Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Check t he transmis s ion OSS s ens or and circui ts .
Refer to the el ect ri cal guides . Rect ify as
neces sary. Refer t o t he warranty pol icy and
procedures manual if t he TCM is s us pect.
P0723-00 Output s haft s peed (OSS)
s ens or circuit (vehi cle
s peed s ens or A circuit )
int ermi tt ent OSS s ens or not ins tall ed
correctl y OSS s ens or ci rcuit :
intermit t ent hi gh res is t ance
in t ermi nals OSS s ens or fault
Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Check t he transmis s ion OSS s ens or for correct
ins tall ati on. Check the OSS s ens or and circuit s .
Refer to the el ect ri cal guides . Rect ify as
neces sary. Refer t o t he warranty pol icy and
procedures manual if t he TCM is s us pect.
P0725-00 Engi ne s peed input ci rcuit Cont roll er area network
(CAN) circui t: open circui t CAN circuit : s hort circui t to
ground CAN module fault Carry out a compl ete vehicle read for CAN
relat ed DTCs. Recti fy as neces sary.
P0729-00 Gear 6 incorrect rati o Cont act resi s tance in the
terminals Sol enoi d regulat ing
incorrectl y Mechanical fault i n
trans mi ss i on - transmis s ion
component s worn and Carry out a compl ete read for related engi ne
torque DTCs . Check trans mi ss i on fl uid l evel and
condit ion. Refer t o the warrant y poli cy and
procedures manual if t he t rans mis s ion i s
sus pect .

Page 143 of 3229

LAND ROVER FRELANDER 2 2006 Repair Manual DT C
Description Possible Cause Action
caus ing s li p or s ys t em
press ure too low
P0730-00 Incorrect gear rat io Int ernal malfuncti on of the
trans mi ss i on Refer to the warrant y pol icy and

DT C
Description Possible Cause Action
caus ing s li p or s ys t em
press ure too low
P0730-00 Incorrect gear rat io Int ernal malfuncti on of the
trans mi ss i on Refer to the warrant y pol icy and procedures
manual i f the t rans mis s ion is s us pect.
P0730-95 Incorrect gear rat io -
incorrect as s embl y Incorrect final gear ins t al led Check t rans mis s ion unit s part numbers. Refer t o
the warrant y pol icy and procedures manual if
the t rans mi ss ion is s us pect .
P0731-00 Gear 1 incorrect rati o Cont act resi s tance in the
terminals Sol enoi d regulat ing
incorrectl y Mechanical fault i n
trans mi ss i on - transmis s ion
component s worn and
caus ing s li p or s ys t em
press ure too low Carry out a compl ete read for related engi ne
torque DTCs . Check trans mi ss i on fl uid l evel and
condit ion. Refer t o the warrant y poli cy and
procedures manual if t he t rans mis s ion i s
sus pect .
P0732-00 Gear 2 incorrect rati o Cont act resi s tance in the
terminals Sol enoi d regulat ing
incorrectl y Mechanical fault i n
trans mi ss i on - transmis s ion
component s worn and
caus ing s li p or s ys t em
press ure too low P0733-00
Gear 3 incorrect rati o Cont act resi s tance in the
terminals Sol enoi d regulat ing
incorrectl y Mechanical fault i n
trans mi ss i on - transmis s ion
component s worn and
caus ing s li p or s ys t em
press ure too low P0734-00
Gear 4 incorrect rati o Cont act resi s tance in the
terminals Sol enoi d regulat ing
incorrectl y Mechanical fault i n
trans mi ss i on - transmis s ion
component s worn and
caus ing s li p or s ys t em
press ure too low P0735-00
Gear 5 incorrect rati o Cont act resi s tance in the
terminals Sol enoi d regulat ing
incorrectl y Mechanical fault i n
trans mi ss i on - transmis s ion
component s worn and
caus ing s li p or s ys t em
press ure too low P0736-00
Reverse gear i ncorrect rat io Int ernal malfuncti on in the
trans mi ss i on cont rol s ys t em Mechanical fault i n
trans mi ss i on. Trans mi ss i on
component s worn and
caus ing s li p or s ys t em
press ure too low Fl uid l evel low/condi ti on poor
P073D-00
Unabl e t o engage neut ral Cont act resi s tance in the
terminals Sol enoi ds st uck in t he on/off
pos it ion. Mechanical fault i n the
trans mi ss i on Check t rans mis s ion flui d level and condit ion.
Refer to the warrant y pol icy and procedures
manual i f the t rans mis s ion is s us pect.
P073E-64 Unabl e t o engage revers e Cont act resi s tance in the
terminals Sol enoi ds st uck in t he on/off
pos it ion. Mechanical fault i n the
trans mi ss i on

Page 144 of 3229

LAND ROVER FRELANDER 2 2006 Repair Manual DT C
Description Possible Cause Action
P073F-00 Unabl e t o engage gear 1 Cont act resi s tance in the
terminals Sol enoi ds st uck in t he on/off
pos it ion. Mechanical fault i n the
trans mi ss i

DT C
Description Possible Cause Action
P073F-00 Unabl e t o engage gear 1 Cont act resi s tance in the
terminals Sol enoi ds st uck in t he on/off
pos it ion. Mechanical fault i n the
trans mi ss i on P0741-00
Torque convert er clutch
s ol enoi d circui t
performance/s tuck off Cont act resi s tance in the
terminals Torque convert er cl ut ch lock
up cont rol s ol enoi d (SLU)
ci rcuit : short ci rcuit t o ground Torque convert er cl ut ch lock
up cont rol s ol enoi d (SLU)
ci rcuit : short ci rcuit t o power Torque convert er cl ut ch lock
up cont rol s ol enoi d (SLU)
ci rcuit : open ci rcuit Torque convert er cl ut ch lock
up sol enoi d (SLU) s t uck i n off
pos it ion Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Refer to the warrant y pol icy and procedures
manual i f the t rans mis s ion or t he TCM i s
sus pect .
P0742-00 Torque convert er clutch
s ol enoi d circui t st uck on Cont act resi s tance in the
terminals Torque convert er cl ut ch lock
up cont rol s ol enoi d (SLU)
ci rcuit : short ci rcuit t o ground Torque convert er cl ut ch lock
up cont rol s ol enoi d (SLU)
ci rcuit : short ci rcuit t o power Torque convert er cl ut ch lock
up cont rol s ol enoi d (SLU)
ci rcuit : open ci rcuit Torque convert er cl ut ch lock
up sol enoi d (SLU) s t uck i n on
pos it ion Int ernal t rans mi ss i on cont rol
modul e (TCM) fault P0744-68
Torque convert er clutch
s ol enoi d circui t
int ermi tt ent Engine st all ed Mechanical fault i n engi ne Carry out a compl ete read for related engi ne
DTCs . Recti fy as necess ary.
P074A-00 Unabl e t o engage gear 2 Cont act resi s tance in the
terminals Sol enoi ds st uck in t he on/off
pos it ion Mechanical fault i n the
trans mi ss i on Check t rans mis s ion flui d level and condit ion.
Refer to the warrant y pol icy and procedures
manual i f the t rans mis s ion is s us pect.
P074B-00 Unabl e t o engage gear 3 Cont act resi s tance in the
terminals Sol enoi ds st uck in t he on/off
pos it ion Mechanical fault i n the
trans mi ss i on P074C-00
Unabl e t o engage gear 4 Cont act resi s tance in the
terminals Sol enoi ds st uck in t he on/off
pos it ion Mechanical fault i n the
trans mi ss i on P074D-00
Unabl e t o engage gear 5 Cont act resi s tance in the
terminals Sol enoi ds st uck in t he on/off
pos it ion Mechanical fault i n the
trans mi ss i on P074E-00
Unabl e t o engage gear 6 Cont act resi s tance in the
terminals Sol enoi ds st uck in t he on/off
pos it ion Mechanical fault i n the
trans mi ss i on P0777-00
Pres s ure control s olenoid B
s tuck on Shi ft s olenoid No. 2 st uck in
the on pos it ion Refer to the warrant y pol icy and procedures
manual i f the t rans mis s ion is s us pect.

Load next 8 pages

Page: < prev 1-10 ... 105-112 113-120 121-128 129-136 137-144 145-152 153-160 161-168 169-176 ... 3232 next >

service schedule four wheel drive odometer torque service rims