2006 LAND ROVER FRELANDER 2 Repair Manual

transmission run flat open gas tank octane alternator heater

Page 65 of 3229

LAND ROVER FRELANDER 2 2006 Repair Manual Publ is hed: 27-Apr-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Terrain
Response Control Module (ATCM)
Des cript ion and Operat ion
Inspection and Verification
CAUTION: Di agnos

Publ is hed: 27-Apr-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Terrain
Response Control Module (ATCM)
Des cript ion and Operat ion
Inspection and Verification
CAUTION: Di agnos is by s ubs ti tut ion from a donor vehicle is NO T acceptabl e. Subs ti tut ion of cont rol modules doesnot guarant ee confirmat ion of a faul t, and may als o caus e addit ional fault s i n t he vehi cl e being t est ed and/or t he donorvehi cl e.
1. Verify t he cus t omer concern.1.
2. Vis ually ins pect for obvious s igns of mechani cal or electrical damage.2.
Visual InspectionMechanicalElectrical
* Ti re condit ion, pres sures, et cDriveline, Engine, Transmis s ion, Sus pensi on,component s (correct ins tall ati on, damage, etc)
Fus esHarness es /Connect orsTerrai n res pons e modul eEngi ne Cont rol Module (ECM)Transmis s ion Control Modul e (TCM)Ant i-Lock Brake Sys t em control modul eAct ive On-demand cont rol moduleDynami c s us pensi on cont rol module * Controllerarea network (CAN) ci rcuit s
3. If an obvious cause for an obs erved or report ed concern is found, correct t he caus e (if pos s ible) beforeproceeding t o t he next s t ep.3.
4. If t he caus e is not vis ually evi dent , check for Di agnos ti c Trouble Codes (DTCs) and refer t o t he DTC Index.4.
DTC Index
• NOTE: If the control modul e/t rans mis s ion i s s uspect and the vehicle remai ns under manufacturer warrant y, refer t o t heW arranty Pol icy and Procedures manual (s ect ion B1.2), or determine i f any pri or approval programme is in operat ion, pri ort o the ins tall ati on of a new module/transmis s ion.
• NOTE: Generic scan t ool s may not read the codes li st ed, or may read only fi ve digit codes . Mat ch the five di git s from t hes can tool to the firs t fi ve di git s of the seven digi t code l is ted to ident ify t he faul t (t he las t t wo digi ts gi ve addi ti onalinformat ion read by the manufact urer approved diagnos t ic s ys tem).
• NOTE: W hen performing el ect ri cal volt age or resi s tance tes t s, al ways us e a digit al mult imet er (DMM) accurate to threedeci mal places , and wi th an up-to-date cali brat ion cert ificate. W hen t es ti ng res is t ance, always take t he res i st ance of t heDMM leads int o account.
• NOTE: Check and recti fy bas ic faul ts before beginni ng diagnos t ic rout ines i nvol vi ng pinpoint t es t s.
• NOTE: Ins pect connect ors for s igns of water ingres s , and pins for damage and/or corros ion.
• NOTE: If DTCs are recorded and, aft er performi ng the pi npoi nt tes ts , a fault is not present , an int ermi tt ent concern maybe t he caus e. Always check for loose connect ions and corroded terminals .
Des cript ion And Operat ion
For a detail ed descripti on of the Terrain Respons e s ys t em, refer t o t he rel evant Descript ion and Operat ion secti on in theworks hop manual .For addit ional informat ion, refer t o: Ride and Handli ng Opti mizat ion (204-06 Ride and Handli ng Opt imi zat ion, Descripti onand Operat ion).
Terrain Response C ontrol ModuleDT CDescriptionPossible CauseAction
C1A00-46Control Module -cal ibrat ion /paramet ermemory fai lure
The Terrain Res ponseCont rol Modul e hasi ndi cat ed a cali brat ion /paramet er memoryfail ure for embeddeds ys tems us i ng FLASHmemory. Thi s i sequivalent t o EEPROM inRAM/ROM/EEPROMembedded s ys t emsCorrupti on in thenon-volat il e memorys t orage s yst em(EEPROM) in t he TerrainRes pons e Cont rolModule
Rect ify thi s DTC before att empti ng t o rect ify others . Recordal l DTCs logged and clear them. W it h ignit ion on sel ect aterrain res pons e s peci al program, t urn off the i gnit ion, thenturn back on the i gni ti on and veri fy t he s elected s peci alprogram is s t il l act ive. If t he s el ect ed t errai n res ponsespecial program is not s t il l act ive and has ret urned t o t hegeneral program, confirm i f DTC has ret urned. Repeatprocedure agai n once more. If DTC is st il l pres ent i nst all anew terrai n res pons e rotary cont rol and control modul e. Referto the warranty pol icy and procedures manual if a module issus pect

Page 66 of 3229

LAND ROVER FRELANDER 2 2006 Repair Manual DT CDescriptionPossible CauseAction
C1A01-96LED Circui t -componentint ernal fail ure
Terrain res pons e rotarycontrol and controlmodul e - LED s hortcircui t t o groundTerrain res pons e rotarycontro

DT CDescriptionPossible CauseAction
C1A01-96LED Circui t -componentint ernal fail ure
Terrain res pons e rotarycontrol and controlmodul e - LED s hortcircui t t o groundTerrain res pons e rotarycontrol and controlmodul e - LED opencircui t
• NOTE: If t he s yst em i s i n 'fails afe default mode due t oanot her i s sue no LEDs will i ll uminate. This fault does notcaus e t he s ys t em t o go t o 'fail safe default '.
Refer to the Des cri pt ion and Operati on s ect ion of works hopmanual . Check t errai n res ponse s ys t em, special programLEDs . One or more of the LEDs i s s uspected of notill uminat ing as appropri ate. W it h the engi ne running movethe t errain respons e rot ary control through al l fi ve programsand confi rm t he appropriat e s peci al program LED does notill uminat e when t he terrain res pons e rotary cont rol i s in thatpos it ion. Sus pect t he terrain res pons e rotary cont rol andcont rol module, check and ins t al l a new t errain respons erot ary cont rol and control modul e as required, refer t o t henew module/component i nst all ati on not e at t he t op of theDTC Index.
C1A02-94Rotary EncoderStuck InInt ermedi at ePosi ti on -unexpectedoperati on
The t errain respons erotary cont rol is hel d i nan intermediate pos i ti on(between t he s peci alprograms ) for more t han60 secondsForei gn objectprevent ing correctoperat ion of t errai nrespons e rot ary controlMechani cal damage t ot he t errai n res ponserotary cont rol
• NOTE: Sus pect driver error do not replace the terrainres pons e rotary cont rol at thi s t ime
Check for forei gn object prevent ing correct operat ion ofterrain res pons e rotary cont rol. St art t he vehi cle engine,rot at e t he t errai n res ponse rot ary control unt il it has l ocat eda genui ne detent, wai t 60 s econds. St op t he vehi cl e engine,cl ear t he DTC and retes t
U0073-88Control ModuleCommunicati onBus "A" Off - busoff
Bus off. The TerrainRes pons e Cont rolModule has det ect ed t hedat a bus is not avail abl eCAN bus open ci rcuitCAN bus short ci rcuit t ogroundCAN bus short ci rcuit t opowerFail ure of anothercontrol modul e on t heCAN bus
Refer to el ect ri cal circui t diagrams , check CAN ci rcuit for openci rcuit , short to ground, s hort t o power, repai r/renew asneces sary. Us i ng the manufact urer approved diagnos t icsys tem, carry out network int egrit y t est . Check t he s yst em isoperat ing correctl y and the DTC does not return.
U0100-87LostCommunicati onW i th ECM/PCM "A"- mi ss i ngmes s age
The Terrain Res ponseCont rol Modul e has notrecei ved one or moreexpect ed mes s ages fromt he Engine ControlModuleHi gh s peed CAN circuitcommunicat ions fai lureOpen ci rcuit EngineCont rol Modul e,powerfeedOpen ci rcuit EngineCont rol Modul e, grounds upplyEngine Cont rol Modul edi sconnect ed from t hehi gh s peed CANcommunicat ion busOpen ci rcuit EngineCont rol Modul e highs peed CAN l ow circui tOpen ci rcuit EngineCont rol Modul e highs peed CAN hi gh ci rcuitEngine Cont rol Modul enot configuredEngine Cont rol Modul efail ure
Usi ng t he manufact urer approved diagnost ic s ys tem, checkthe Engine Cont rol Modul e for DTCs and refer t o t he rel evantDTC index. Usi ng the manufact urer approved diagnos t icsys tem, carry out network int egrit y t est . Us ing t hemanufact urer approved diagnos t ic s ys tem, re-configure t heEngi ne Cont rol Module. Refer t o electrical ci rcuit diagrams,check power feed and ground s uppl ies , to Engi ne Cont rolModul e for open circui t. Check for open circuit Engine Cont rolModul e high s peed CAN l ow circui t. Check for open circuitEngi ne Cont rol Module hi gh s peed CAN high circui t, repai r asneces sary
U0101-87LostCommunicati onwit h TCM -mi ss i ng mes sage
The Terrain Res ponseCont rol Modul e has notrecei ved one or moreexpect ed mes s ages fromt he Trans mi ss ionCont rol Modul eHi gh s peed CAN circuitcommunicat ions fai lureOpen ci rcuitTrans mi s si on Cont rolModule, powerfeedOpen ci rcuit
Usi ng t he manufact urer approved diagnost ic s ys tem, checkthe Trans mi s si on Cont rol Module for DTCs and refer to therelevant DTC index. Usi ng t he manufact urer approveddi agnos t ic s yst em, carry out net work i ntegri ty tes t. Us i ng themanufact urer approved diagnos t ic s ys tem, re-configure t heTransmis s ion Control Modul e. Refer t o el ect ri cal circui tdi agrams , check power feed and ground s upplies , t oTransmis s ion Control Modul e for open circui t. Check for openci rcuit Trans mi ss i on Cont rol Module hi gh s peed CAN lowci rcuit . Check for open circui t Trans mis s ion Cont rol Modul ehi gh s peed CAN high circui t, repai r as neces s ary

Page 67 of 3229

LAND ROVER FRELANDER 2 2006 Repair Manual DT CDescriptionPossible CauseAction
Trans mi s si on Cont rolModule, ground s upplyTrans mi s si on Cont rolModule dis connect edfrom t he high s peedCAN communi cat ion busOpen ci rcuitTrans mi s si

DT CDescriptionPossible CauseAction
Trans mi s si on Cont rolModule, ground s upplyTrans mi s si on Cont rolModule dis connect edfrom t he high s peedCAN communi cat ion busOpen ci rcuitTrans mi s si on Cont rolModule high s peed CANl ow circui tOpen ci rcuitTrans mi s si on Cont rolModule high s peed CANhi gh ci rcuitTrans mi s si on Cont rolModule not confi guredTrans mi s si on Cont rolModule fail ure
U0121-87LostCommunicati onW i th Ant i-LockBrake Sys tem(ABS) ControlModule - mis s ingmes s age
The Terrain Res ponseCont rol Modul e has notrecei ved one or moreexpect ed mes s ages fromt he Anti -Lock BrakeSys tem Cont rol ModuleHi gh s peed CAN circuitcommunicat ions fai lureOpen ci rcuit Anti -LockBrake Sys t em ControlModule, powerfeedOpen ci rcuit Anti -LockBrake Sys t em ControlModule, ground s upplyAnt i-Lock Brake Sys temCont rol Modul edi sconnect ed from t hehi gh s peed CANcommunicat ion busOpen ci rcuit Anti -LockBrake Sys t em ControlModule high s peed CANl ow circui tOpen ci rcuit Anti -LockBrake Sys t em ControlModule high s peed CANhi gh ci rcuitAnt i-Lock Brake Sys temCont rol Modul e notconfi guredAnt i-Lock Brake Sys temCont rol Modul e fai lure
Usi ng t he manufact urer approved diagnost ic s ys tem, checkthe Ant i-Lock Brake Sys tem Control Module for DTCs and referto the relevant DTC index. Us ing the manufact urer approveddi agnos t ic s yst em, carry out net work i ntegri ty tes t. Us i ng themanufact urer approved diagnos t ic s ys tem, re-configure t heAnt i-Lock Brake Sys t em Control Modul e. Refer to el ect ri calci rcuit diagrams, check power feed and ground s uppl ies , toAnt i-Lock Brake Sys t em Control Modul e for open circui t. Checkfor open ci rcuit Ant i-Lock Brake Sys tem Control Module highspeed CAN low circui t. Check for open circui t Ant i-Lock BrakeSys t em Control Modul e high s peed CAN high ci rcuit , repair asneces sary. Sus pect t he Anti -Lock Brake Syst em Cont rolModul e, check and ins tal l a new Anti -Lock Brake Sys temCont rol Module as requi red, refer to the newmodul e/component i ns t allat ion not e at t he top of t he DTCIndex. Check t he sys t em i s operati ng correctl y and t he DTCdoes not ret urn.
U0136-87LostCommunicati onW i th Different ialControl Module -Rear - mis s ingmes s age
The Terrain Res ponseCont rol Modul e has notrecei ved one or moreexpect ed mes s ages fromt he Rear Different ialCont rol Modul eHi gh s peed CAN circuitcommunicat ions fai lureOpen ci rcuit RearDi fferenti al Cont rolModule, powerfeedOpen ci rcuit RearDi fferenti al Cont rolModule, ground s upplyRear Different ial ControlModule dis connect edfrom t he high s peedCAN communi cat ion busOpen ci rcuit RearDi fferenti al Cont rolModule high s peed CANl ow circui tOpen ci rcuit RearDi fferenti al Cont rolModule high s peed CANhi gh ci rcuitRear Different ial ControlModule not confi guredRear Different ial ControlModule fail ure
Usi ng t he manufact urer approved diagnost ic s ys tem, checkthe Rear Different ial Control Modul e for DTCs and refer to therelevant DTC index. Usi ng t he manufact urer approveddi agnos t ic s yst em, carry out net work i ntegri ty tes t. Us i ng themanufact urer approved diagnos t ic s ys tem, re-configure t heRear Di fferenti al Cont rol Modul e. Refer to el ect ri cal circui tdi agrams , check power feed and ground s upplies , t o RearDifferent ial Cont rol Module for open ci rcuit . Check for openci rcuit Rear Different ial Control Module high s peed CAN lowci rcuit . Check for open circui t Rear Different ial Cont rol Modulehi gh s peed CAN high circui t, repai r as neces s ary. Sus pect theRear Di fferenti al Cont rol Modul e, check and ins tal l a new RearDifferent ial Cont rol Module as required, refer to the newmodul e/component i ns t allat ion not e at t he top of t he DTCIndex. Check t he sys t em i s operati ng correctl y and t he DTCdoes not ret urn.

Page 68 of 3229

LAND ROVER FRELANDER 2 2006 Repair Manual DT CDescriptionPossible CauseAction
U0140-87LostCommunicati onW i th Body Cont rolModule - mis s ingmes s age
The Terrain Res ponseCont rol Modul e has notrecei ved one or moreexpect ed mes s ages f

DT CDescriptionPossible CauseAction
U0140-87LostCommunicati onW i th Body Cont rolModule - mis s ingmes s age
The Terrain Res ponseCont rol Modul e has notrecei ved one or moreexpect ed mes s ages fromt he Body Control ModuleHi gh s peed CAN circuitcommunicat ions fai lureOpen ci rcuit BodyCont rol Modul e,powerfeedOpen ci rcuit BodyCont rol Modul e, grounds upplyBody Control Modul edi sconnect ed from t hehi gh s peed CANcommunicat ion busOpen ci rcuit BodyCont rol Modul e highs peed CAN l ow circui tOpen ci rcuit BodyCont rol Modul e highs peed CAN hi gh ci rcuitBody Control Modul e notconfi guredBody Control Modul efail ure
Usi ng t he manufact urer approved diagnost ic s ys tem, checkthe Body Control Modul e for DTCs and refer t o the relevantDTC index. Usi ng the manufact urer approved diagnos t icsys tem, carry out network int egrit y t est . Us ing t hemanufact urer approved diagnos t ic s ys tem, re-configure t heBody Cont rol Modul e. Refer to elect rical circui t diagrams ,check power feed and ground s uppl ies , to Body Cont rolModul e for open circui t. Check for open circuit Body ControlModul e high s peed CAN l ow circui t. Check for open circuitBody Cont rol Modul e high speed CAN hi gh circuit , repair asneces sary. Sus pect t he Body Cont rol Module, check andins tall a new Body Cont rol Module as required, refer to thenew module/component i nst all ati on not e at t he t op of theDTC Index. Check t he s ys t em i s operati ng correct ly and t heDTC does not return.
U0300-55Int ernal Cont rolModule Soft wareIncompati bili ty -not configured
The Terrain Res ponseCont rol Modul e hasfail ed to recogni se amat ching mas t erconfi gurati on ID fromt he CAN dat a busmas t erTerrain Res ponseCont rol Modul e hasi ncorrect CANconfi gurati onCAN bus mast er notcorrect ly confi guredMes s age cont ainingconfi gurati on ID notrecei ved due to CAN busi s sueMes s age cont ainingconfi gurati on ID nott rans mi tt ed by CAN busmas t er
Usi ng t he manufact urer approved diagnost ic s ys tem, checkthe CAN configurat ion i n the Terrai n Respons e ControlModul e, check correct s oftware vers ions i nst all ed and updat eas neces sary. If s imi lar DTCs from other modules s uspectCAN bus or CAN bus mas ter ECU, check CAN bus operat ion,check the CAN configurat ion i n t he CAN bus mas t er modul e,check correct s oft ware vers i ons ins tall ed and updat e asneces sary. Check the sys tem is operati ng correctl y and t heDTC does not return.
U0401-94Invali d Dat aRecei ved FromECM/PCM -unexpectedoperati on
The Terrain Res ponseCont rol Modul e hasdet ect ed that t heEngine Cont rol Modul ecomponent had operat edi n a way or at a ti met hat it had not beencommanded t o operateThe engine managements ys tem, Engine Cont rolModule is unable t os upport normal t errai nrespons e functi onal it y,t he t errai n res ponses ys tem wil l go int odefaul t condit ionEngine managements ys tem faultEngine Cont rol Modul efail ure
Usi ng t he manufact urer approved diagnost ic s ys tem, checkthe Engine Cont rol Modul e for DTCs and refer t o t he rel evantDTC index, recti fy as requi red. Check t he s yst em is operat ingcorrectl y and the DTC does not return
U0402-94Invali d Dat aRecei ved FromTrans mis s ionControl Module -unexpectedoperati on
The Terrain Res ponseCont rol Modul e hasdet ect ed that t heTrans mi s si on Cont rolModule component hadoperat ed in a way or ata ti me t hat it had notbeen commanded tooperat eThe t rans mi ss ions ys tem, Trans mi ss i onCont rol Modul e i s unabl et o s upport normal
Usi ng t he manufact urer approved diagnost ic s ys tem, checkthe Trans mi s si on Cont rol Module for DTCs and refer to therelevant DTC index, recti fy as requi red. Check the s ys tem isoperat ing correctl y and the DTC does not return

Page 69 of 3229

LAND ROVER FRELANDER 2 2006 Repair Manual DT CDescriptionPossible CauseAction
t errain respons efunct ionali ty, the terrainrespons e s yst em will goi nto defaul t condit ionTrans mi s si on s ys t emfaultTrans mi s si on Cont rolModule fai

DT CDescriptionPossible CauseAction
t errain respons efunct ionali ty, the terrainrespons e s yst em will goi nto defaul t condit ionTrans mi s si on s ys t emfaultTrans mi s si on Cont rolModule fail ure
U0415-94Invali d Dat aRecei ved FromAnti -Lock BrakeSyst em Cont rolModule -unexpectedoperati on
The Terrain Res ponseCont rol Modul e hasdet ect ed that t heAnt i-Lock Brake Sys temcontrol modul ecomponent had operat edi n a way or at a ti met hat it had not beencommanded t o operateThe Ant i-Lock BrakeSys tem , Anti -LockBrake Sys t em controlmodul e is unable tos upport normal t errai nrespons e functi onal it y,t he t errai n res ponses ys tem wil l go int odefaul t condit ionAnt i-Lock Brake Sys temfaultAnt i-Lock Brake Sys temcontrol modul e fai lure
Usi ng t he manufact urer approved diagnost ic s ys tem, checkthe Ant i-Lock Brake Sys tem cont rol module for DTCs and referto the relevant DTC index, rect ify as requi red. Check t hesys tem is operati ng correctl y and t he DTC does not return.Sus pect t he Ant i-Lock Brake Sys tem cont rol module, checkand ins tall a new Anti -Lock Brake Syst em cont rol module asrequired, refer to the new module/component i nst all at ionnot e at t he top of t he DTC Index.
U0437-94Invali d Dat aRecei ved FromDifferent ialControlModule-Rear -unexpectedoperati on
The Terrain Res ponseCont rol Modul e hasdet ect ed that t he RearDi fferenti al Cont rolModule component hadoperat ed in a way or ata ti me t hat it had notbeen commanded tooperat eThe Rear Different ials ys tem, RearDi fferenti al Cont rolModule is unable t os upport normal t errai nrespons e functi onal it y,t he t errai n res ponses ys tem wil l go int odefaul t condit ionRear Different ial s yst emfaultRear Different ial ControlModule fail ure
Usi ng t he manufact urer approved diagnost ic s ys tem, checkthe Rear Different ial Module for DTCs and refer t o t herelevant DTC index, recti fy as requi red. Check the s ys tem isoperat ing correctl y and the DTC does not return. Sus pect t heRear Di fferenti al Module, check and i nst all a new RearDifferent ial Modul e as requi red, refer t o t he newmodul e/component i ns t allat ion not e at t he top of t he DTCIndex.
U2012-4ACar Configurat ionParamet er(s) -incorrectcomponentins t al led
The Terrain Res ponseCont rol Modul e hasdet ect ed a mi s matchbet ween the hardwareconnect ed and thehardware expect edVehicle not correctl yconfi guredIncorrect componentsi nst all ed for vehicleconfi gurati on
Usi ng t he manufact urer approved diagnost ic s ys tem, checkthe vehicle confi gurati on file, rect ify as neces s ary. Checkcorrect components for vehi cl e configurat ion are i ns t alled,recti fy as necess ary. Check the s ys tem is operat ing correctl yand the DTC does not ret urn.

Page 70 of 3229

LAND ROVER FRELANDER 2 2006 Repair Manual Publi shed: 06-Jul-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Body
Control Module (BCM)
Des cript ion and Operat ion
• NOTE: If a cont rol module or component i s s uspect

Publi shed: 06-Jul-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Body
Control Module (BCM)
Des cript ion and Operat ion
• NOTE: If a cont rol module or component i s s uspect and the vehicl e remai ns under manufacturer warrant y, refer t o t heW arranty Pol icy and Procedures manual (s ect ion B1.2), or determine i f any pri or approval program is i n operat ion, beforet he replacement of a component.
• NOTE: Generic scan t ool s may not read the codes li st ed, or may read only 5-digi t codes . Match t he 5 digi ts from t he s cant ool t o t he fi rs t 5 di gi ts of the 7-digit code li s ted t o i dent ify the fault (the last 2 digi ts gi ve ext ra informati on read by themanufacturer-approved di agnos ti c s ys t em).
• NOTE: W hen performing volt age or res is t ance t est s , always use a digi tal mult imeter (DMM) accurat e t o t hree deci malplaces, and wi th an up-t o-date cal ibrat ion cert ificate. W hen tes ti ng res is t ance al ways take t he res is t ance of t he DMMleads i nt o account .
• NOTE: Check and recti fy bas ic faul ts before beginni ng diagnos t ic rout ines i nvol vi ng pinpoint t es t s.
• NOTE: Ins pect connect ors for s igns of water ingres s , and pins for damage and/or corros ion.
• NOTE: If DTCs are recorded and, aft er performi ng the pi npoi nt tes ts , a fault is not present , an int ermi tt ent concern maybe t he caus e. Always check for loose connect ions and corroded terminals .
For addit ional informat ion, refer t o: Communicati ons Net work (418-00 Modul e Communicati ons Net work, Des cript ion andOperat ion).
Body control module (BC M)
DT CDescriptionPossible CauseAction
B100A-11Fuel PumpAuthoris ati on - ci rcuits hort t o ground
Fuel pump authori s at ionci rcuit - s hort t o groundRefer to electrical ci rcuit diagrams and check fuel pumpaut hori sat ion circui t for s hort t o ground
B100A-15Fuel PumpAuthoris ati on - ci rcuits hort t o power oropen
Fuel pump authori s at ionci rcuit - s hort t o power,open circui t
Refer to electrical ci rcuit diagrams and check fuel pumpaut hori sat ion circui t for s hort t o power, open circui t
B1024-08Trans ponder - Buss ignal/Mess ageFailures
Trans ponder - Buss i gnal /mes s age fail uresCarry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys tem
B1024-51Start Cont rol Uni t -not programmedSt art control uni t - notconfi guredRe-configure the st art control uni t usi ng themanufacturer approved diagnost ic sys tem
B1024-81Start Cont rol unit -invali d s eri al dat areceived
Inval id serial data recei vedCarry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys tem
B1024-87Start cont rol unit -mi ss i ng mes sageMis si ng mes s ageCarry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys tem
B1024-96Start cont rol unit -component int ernalfai lure
Internal fail ureIns t al l a new s t art cont rol unit , refer to newmodule/component i nst all at ion not e at t he top of t heDTC IndexB1025-81Trans ponder - invali ds eri al dat aInval id serial data recei vedCarry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys temB1026-08Steering Column Lock- Bus Signal/Mes sageFailures
St eering col umn lock - Buss i gnal /mes s age fail uresCarry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys tem
B1026-51Steering Column Lock- not programmedSt eering col umn lock - notconfi guredRe-configure the st eeri ng col umn lock us ing t hemanufacturer approved diagnost ic sys tem
B1026-52Steering Column Lock- not act ivat edRequest to enable thes t eering column locks upply not approved
Check LIN circui t bet ween s teering column l ock and CJB
B1026-71Steering Column Lock- actuator s t uckShould be set i f the SCL isunable to reach locked andO K posi ti on
Carry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys tem
B1026-82Steering Column LockSt eering col umn locki ncorrectl y programmedIns t al l a new s t eering column lock
B1026-92Steering Column Lock- performance orincorrect operat ion
Micro s wi tch/s ens or faultCarry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys tem
B1026-94Steering Column Lock- unexpectedoperati on
St atus mes s ages arerecei ved from t he SCLwhen SCL should be turnedoff
Carry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys tem
B1026-96Steering Column Lock- component i nt ernalfai lure
Internal fail ureIns t al l a new s t eering column lock, refer t o t he newmodule/component i nst all at ion not e at t he top of t heDTC Index

Page 71 of 3229

LAND ROVER FRELANDER 2 2006 Repair Manual DT CDescriptionPossible CauseAction
B1029-21Accel erator PedalSensor s ignalampli tude < mi ni mum
Accelerat or pedal s ens ors i gnal <3% of supply(5V)Carry out the pi npoint t es ts as s oci at

DT CDescriptionPossible CauseAction
B1029-21Accel erator PedalSensor s ignalampli tude < mi ni mum
Accelerat or pedal s ens ors i gnal <3% of supply(5V)Carry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys tem
B1029-22Accel erator PedalSensor s ignalampli tude >maximum
Accelerat or pedal s ens ors i gnal >=97% ofs upply(5V)
Carry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys tem
B108A-23Start butt on - s ignals tuck l owSW 1 and SW 2 cons tant lyact iveCarry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys tem
B108B-23Start Butt on Circui t"A" - si gnal s t uck l owSW 1 cons t ant ly act ive forl ong ti me whi le but tonpress det ect ed at SW 2
Carry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys tem
B108B-24Start butt on circuit"A" - si gnal s t uck hi ghSW 1 never acti ve whil ebut ton press det ect ed atSW 2
Carry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys tem
B108C-23Start butt on circuit"B" - si gnal s t uck l owSW 2 cons t ant ly act ive forl ong ti me whi le but tonpress det ect ed at SW 1
Carry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys tem
B108C-24Start butt on circuit"B" - si gnal s t uck hi ghSW 2 never acti ve whil ebut ton press det ect ed atSW 1
Carry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys tem
B108D-24Start butt on circuit"C" si gnal s t uck hi ghSW 3 never acti ve whil ebut ton press det ect ed atSW 1
Carry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys tem
B1095-12W i per On/Off Rel ay -circui t short to powerW iper On/O ff rel ay circuit -s hort t o powerRefer to electrical ci rcuit diagrams and check wi perOn/Off rel ay ci rcuit for short to power
B1095-14W i per On/Off Rel ay -circui t short to groundor open
W iper On/O ff rel ay circuit -s hort t o ground, openci rcuit
Refer to electrical ci rcuit diagrams and check wi perOn/Off rel ay ci rcuit for short to ground, open circui t
B1096-12W i per High/Low Rel ay- circui t short topower
W iper High/Low rel ayci rcuit - s hort t o powerRefer to electrical ci rcuit diagrams and check wi perHigh/Low relay ci rcuit for s hort t o power
B1096-14W i per High/Low Rel ay- circui t short toground or open
W iper High/Low rel ayci rcuit - s hort t o ground,open circui t
Refer to electrical ci rcuit diagrams and check wi perHigh/Low relay ci rcuit for s hort t o ground, open ci rcuit
B1097-12Heated W inds hieldRelay - circui t s hortt o power
Heat ed winds hield relayci rcuit - s hort t o powerRefer to electrical ci rcuit diagrams and check heatedwinds hield relay circui t for s hort t o power
B1097-14Heated W inds hieldRelay - circui t s hortt o ground or open
Heat ed winds hield relayci rcuit - s hort t o ground,open circui t
Refer to electrical ci rcuit diagrams and check heatedwinds hield relay circui t for s hort t o ground, open ci rcuit
B109B-11License Pl ate Li ght -circui t short to groundLi cens e plat e lamp circuit -s hort t o groundRefer to electrical ci rcuit diagrams and check li cens eplate lamp ci rcuit for short to ground
B109B-13License Pl ate Li ght -open circuitLi cens e plat e lamp circuit -open circui tRefer to electrical ci rcuit diagrams and check li cens eplate lamp ci rcuit for open circui t
B10A2-02Cras h Input - generals ignal fail ureIncorrect s ignal recei vedCarry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys temB10A2-11Cras h Input - ci rcuits hort t o groundCrash input ci rcuit - s hortt o groundCarry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys tem
B10A2-15Cras h s i gnal - circui ts hort t o power oropen
Crash s ignal circui t - s hortt o power, open circui tCarry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys tem
B10A2-68Cras h s i gnal - eventinformat ionCrash s ignal - eventi nformati onCheck RCM for DTCs and refer to the relevant DTCIndex
B10A5-12Alarm Si ren - ci rcuits hort t o powerAl arm s iren ci rcuit - s hortt o powerRefer to electrical ci rcuit diagrams and check alarms iren ci rcuit for short to power
B10A5-14Alarm Si ren - ci rcuits hort t o ground oropen
Al arm s iren ci rcuit - s hortt o ground, open circuitRefer to electrical ci rcuit diagrams and check alarms iren ci rcuit for short to ground, open circuit
B10AC-86Crui se Cont rol Swi tch- Signal invalidSi gnal i nvali dCarry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys temB10AC-87Crui se Cont rol Swi tch- Mi ss i ng mes sageMis si ng mes s ageCarry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys tem
B10AC-95Crui se Cont rol Swi tch- W rong as sembl yMis -mat ch between CarConfigurat ion Fil e andvehicle
Check/up-dat e Car Configurat ion Fi le us i ng themanufacturer approved diagnost ic sys tem

Page 72 of 3229

LAND ROVER FRELANDER 2 2006 Repair Manual DT CDescriptionPossible CauseAction
B10AD-04Rain Sens or - Sys t emInt ernal FailureInternal s ens or fail ureIns t al l a new rain s ens or, refer to newmodule/component i nst all at ion not e at

DT CDescriptionPossible CauseAction
B10AD-04Rain Sens or - Sys t emInt ernal FailureInternal s ens or fail ureIns t al l a new rain s ens or, refer to newmodule/component i nst all at ion not e at t he top of t heDTC Index
B10AD-09Rain Sens or -Component Fail uresRai n s ens or incorrect lyi nst all edRai n s ens or int ernal fail ure
Check for correct ins tal lati on of rai n s ens or. Ins tall anew s ens or as requi red, refer t o newmodule/component i nst all at ion not e at t he top of t heDTC Index
B10BE-11Solar Sens or - circui ts hort t o groundSunload s ens or circui t -s hort t o groundRefer to electrical ci rcuit diagrams and check s unl oads ens or for s hort t o ground
B10BE-13Solar Sens or - opencircui tSunload s ens or circui t -open circui tRefer to electrical ci rcuit diagrams and check s unl oads ens or for open circuit
B10C0-12Fuel Pump PowerSuppl y - circui t shortt o power
Fuel pump power supplyci rcuit - s hort t o powerRefer to electrical ci rcuit diagrams and check fuel pumppower s upply circui t for s hort t o power
B10C0-14Fuel Pump PowerSuppl y - circui t shortt o ground or open
Fuel pump power supplyci rcuit - s hort t o ground,open circui t
Refer to electrical ci rcuit diagrams and check fuel pumppower s upply circui t for s hort t o ground, open ci rcuit
B10D7-94PATS Key -unexpected operat ionNo res pons e fromt rans ponder i n keyRepl ace key
B10E5-11PCM wake-up si gnal -circui t short to groundEngine Cont rol Module(ECM) wake-up s ignalci rcuit - s hort t o ground
Refer to electrical ci rcuit diagrams and check ECMwake-up s ignal ci rcuit for short to ground
B10E5-15PCM wake-up si gnal -circui t short to poweror open
Engine Cont rol Module(ECM) wake-up s ignalci rcuit - s hort t o power,open circui t
Refer to electrical ci rcuit diagrams and check ECMwake-up s ignal ci rcuit for short to power, open circui t
B10E7-12Igni ti on On Relay -circui t short to powerEJB i gni ti on On relaycontrol ci rcuit - s hort t opower
Refer to electrical ci rcuit diagrams and check EJBignit ion relay control ci rcuit for s hort t o power
B10E7-14Igni ti on On Relay -circui t short to groundor open
EJB i gni ti on On relaycontrol ci rcuit - s hort t oground, open circuit
Refer to electrical ci rcuit diagrams and check EJBignit ion relay control ci rcuit for s hort t o ground, openci rcuit
B10EA-12Posi ti ve t emperaturecoeffi ci ent heat er -circui t short to power
Pos it ive t emperat urecoefficient heater circuit -s hort t o power
Refer to electrical ci rcuit diagrams and check posi ti vetemperat ure coeffici ent heater circui t for s hort t o power
B10EA-14Posi ti ve t emperaturecoeffi ci ent heat er -circui t short to groundor open
Pos it ive t emperat urecoefficient heater circuit -s hort t o ground, openci rcuit
Refer to electrical ci rcuit diagrams and check posi ti vetemperat ure coeffici ent heater circui t for s hort t oground, open circui t
B10EB-77Driver door doubl elocking mot or -commanded pos i ti onnot reachabl e
Incorrect feedback fromDDMCheck for Los t Communicati ons DTCs and carry outass ociated pi npoi nt tes t us ing manufacturer approveddiagnos t ic s ys tem. If no los t communicati on DTC, checkdoubl e locking mechani s m for mechanical fail ureB10EC-77Pass enger doordoubl e l ocking mot or- commanded pos i ti onnot reachabl e
Incorrect feedback fromPDMCheck for Los t Communicati ons DTCs and carry outass ociated pi npoi nt tes t us ing manufacturer approveddiagnos t ic s ys tem. If no los t communicati on DTC, checkdoubl e locking mechani s m for mechanical fail ureB10ED-77Rear door dri ver s i dedoubl e l ocking mot or- commanded pos i ti onnot reachabl e
Incorrect feedback fromrear door dri ver s i deCheck DDM for Los t Communicat ions DTCs and carryout as s oci ated pi npoi nt t es t usi ng manufacturerapproved di agnos ti c s yst em. If no los t communi cat ionDTC, Carry out t he pinpoint t est s as sociat ed t o thi sDTC us ing t he manufacturer approved diagnos ti cs ys t em, check doubl e locking mechanis m formechanical fai lure
B10EE-77Rear door pas sengers ide double l ocki ngmot or - commandedposi ti on notreachabl e
Incorrect feedback fromrear door pas senger si deCheck PDM for Lost Communi cat ions DTCs and carry outass ociated pi npoi nt tes t us ing manufacturer approveddiagnos t ic s ys tem. If no los t communicati on DTC, Carryout the pi npoint t es ts as s oci at ed t o t his DTC us ing themanufacturer approved diagnost ic sys tem, check doublelocki ng mechani sm for mechanical fail ureB10EF-12Sunroof Speed Out put- circui t short topower
Sunroof s peed out putci rcuit - s hort t o powerRefer to electrical ci rcuit diagrams and check s unroofs peed out put circui t for s hort t o power
B10EF-14Sunroof Speed Out put- circui t short toground or open
Sunroof s peed out putci rcuit - s hort t o ground,open circui t
Refer to electrical ci rcuit diagrams and check s unroofs peed out put circui t for s hort t o ground, open ci rcuit
B10F2-12Sunroof cont rol -circui t short to powerSunroof cont rol circui t -s hort t o powerRefer to electrical ci rcuit diagrams and check s unroofcont rol circuit for s hort to power

Load next 8 pages

Page: < prev 1-10 ... 33-40 41-48 49-56 57-64 65-72 73-80 81-88 89-96 97-104 ... 3232 next >

emergency towing tire type child restraint park assist battery jump start terminals