Page 2929 of 3229
209
Vehicle recovery
R
4. Apply the foot brake, and select neutral.
5. With the footbrake still applied, release the
park brake.
6. The vehicle can now be towed a maximum
of 80 km (50 miles) at a maximum speed
of 80 kmh (50 mph).
7. Upon arrival at the destination, ensure
wherever possible that the vehicle is
parked on firm level ground.
8. Apply the park brake, and place the
selector lever into the P (park) position.
9. Switch off the ignition, and remove the
remote control.
10. Remove the towing attachment from the
towing eye.
CAUTION
Leaving the ignition switched on for
extended periods will ca use the battery to
drain.
WARNING
Use extreme caution when detaching
towing equipment. Vehicle movement
is possible which can resu lt in serious injuries.
Page 2930 of 3229

Vehicle identification
210
L
Vehicle identificationVEHICLE IDENTIFICATION PLATE
The Vehicle Identification Number (VIN) and
recommended maximum vehicle weights, are
stamped on a plate rivetted to the lock side of
the left-hand (right hand in China) front door
aperture at the bottom. VIN should match the
VIN recorded in the Serv ice Portfolio, and the
VIN visible through the front windscreen.
VEHICLE IDENTIFICATION NUMBER
(VIN)
As a deterrent to thieves, and to assist the
Police, the VIN is stam ped on a plate which is
visible through the lowest pa rt of the left side of
the windscreen.
Note: If you need to communicate with a Land
Rover Dealer/Authorised repairer, you may be
asked to quote the VIN number.
VEHICLE BUILD DATE PLATE
This is the calendar mont h and year in which
the body and power train assemblies were
conjoined and the vehicle was driven from the
production line.
The vehicle built date is shown on a the tyre
pressure label attached to the right-hand 'B'
post.
E83693
Made by Land Rover
LRC PLREB RIMINI RED
LAND ROVER
SALFAXXXXXXXXXXXXe11*XXXX/XXX*XXXX
XXXX kg
XXXX kg
1-
2- XXXX kg
XXXX kg
E83694
SALFAXXXXXXXXXXXX
Page 2931 of 3229
211
Technical specifications
R
Technical specificationsENGINE SPECIFICATIONS
Data Petrol
Number of cylinders 6 Displacement cc's 3192
Firing order 1-5-3-6-2-4
Compression ratio 10.8:1
Power output kW (PS) 171 (233) at 6300 rpm
Maximum torque Nm 317 at 3200 rpm
Data Diesel Diesel with DPF
Number of cylinders 4 4 Displacement cc's 2179 2179 Firing order 1-3-4-2 1-3-4-2
Compression ratio 16.5:1 16.5:1
Power output kW (PS) 118 (160) at 4000 rpm Belgium 110 (150) at 4000
rpm 112 (152) at 4000 rpm
Belgium 110 (150) at 4000 rpm
Maximum torque Nm 400 at 2000 rpm 400 at 2000 rpm
Page 2932 of 3229
Technical specifications
212
L
WEIGHTS
¹ This figure includes the tool kit, all fluids to
the correct levels, and spare wheel, but
excludes the driver and passengers.
² The maximum permissi ble weight of the
vehicle including passengers and load. ³ The maximum permissi
ble weight of the
vehicle and braked trailer including their
respective loads.
Note: ¹ The front and rear axle maximum loads
can not be reached simult aneously as this will
exceed the GVW limit.
² This figure includes the weight of the roof
rack. Variant Approximate unladen
weight¹ Gross Vehicle Weight
(GVW)² Gross Train Weight³
Petrol 1825 kg 4020 lbs 2505 kg
5520 lbs 4505 kg
9930 lbs
Diesel 1820 kg 4010 lbs 2505 kg
5520 lbs 4505 kg
9935 lbs
Variant Maximum front axle load¹ Maximum rear
axle load¹ Maximum roof
rack load² Maximum
payload
Petrol and Diesel 1310 kg 2885 lbs 1360 kg
2995 lbs 75 kg
165 lbs 500 kg
1100 lbs
Page 2933 of 3229
213
Technical specifications
R
DIMENSIONS
2
E8238416
5
438
7
Item Description mm/inches Degrees 1 Width 2180/85.7 -
1 Width with mirrors folded 2005/78.8 -
2 Maximum height (inc roof rails) 1820/71.6 -
3 Approach angle - 31°
4 Breakover angle - 157°
5 Wheelbase 2660/104.7 -
6 Length excluding number plate plinth 4500/177.1 -
7 Track - front 1601/63 -
7 Track - rear 1614/63.5 -
8 Departure angle without tow hitch - 34°
8 Departure angle with detachable tow ball - 18°
- Turning circle (kerb to kerb) 11.3m/37.1ft -
- Maximum wading depth 500/19.7 -
Page 2934 of 3229
Technical specifications
214
L
Wheel alignment data (China only)
Clutch and brake pedal travel (China
only)
The clutch and brake pedal travel are set at the
factory and non-adjustable. Wheel alignment -
front Wheel alignment -
rear Camber - front Camber - rear Castor - front and
rear
+0.30° +0.46° -0.5° -1.95° Non-adjustable
Page 2935 of 3229
215
Type approval
R
Type approvalDeclarations of conformity
E84189
Page 2936 of 3229
Type approval
216
L
E84190