Page 865 of 3229
13. CAUTIONS:
Not e t he thi cknes s of the gas ket removed.
The gas ket t hicknes s i s ident ifi ed by t he numberof holes (1 t o 4) at eit her of t he locati ons shown.
13.
14.
15. NOTE: Do not dis ass emble further if t he componenti s removed for acces s onl y.15.
Page 866 of 3229
16.
Installation Inst all t he li ft ing brackets and ti ght en t he bol ts .
T orque: 10 Nm 1.
2. CAUTION: Only use a plas ti c s craper t o clean
off t he old gas ket.
Clean and i nspect the cyli nder head and cylinder block.
2. Check cyli nder head face for dis torti on, acros s t he
cent er and from corner t o corner.
Refer t o: Specificati ons (303-01B Engine - TD4 2.2L
Di es el, Specifi cat ions ).
3.
If neces sary, s elect t he correct thi cknes s cyl inder head gas ket .
Refer t o: Cyl inder Head Gasket Selecti on - TD4 2.2L Di esel (303-00
Engine Sys tem - General Informati on, General Procedures ).
4.
5. CAUTIONS: Make s ure that t he mat ing faces are clean and free of foreign
mat eri al . Make s ure the locat ing dowels are i nst all ed correctl y.
5.
Page 867 of 3229

Stage 1:
Stage 2:
Stage 3: Make s ure to ins tal l a gas ket of the correct thicknes s
Make s ure that t he gasket is correctl y located.
Inst all a new cyli nder head gas ket .
6. W ARNING: Thi s s tep requi res t he aid of anot her t echni ci an.
CAUTION: Make s ure that t he component is correct ly locat ed
on t he locati ng dowels .
Inst all t he cyl inder head.
6. 7. CAUTION: Make s ure that new cylinder head
bolt s are ins tal led.
Tight en the cyli nder head bolt s in three s tages t o the
s equence s hown.
T orque: 20 Nm 60 Nm
220°7.
8. CAUTIONS: Make s ure that t he mat ing faces are clean and free of foreign
mat eri al . Lubri cat e t he bearing s urfaces wit h clean engine oil .
Make s ure that t hes e component s are ins tal led t o t he noted
removal posi ti on.
Inst all t he camshaft roll er foll owers .
8.
Connect t he glow pl ug electrical connect ors and s ecure t he harnes s
t o t he cyl inder head.
9.
Connect and s ecure t he cool ant hos e.
10.
Inst all t he ti ming bel t rear cover, ti ght en t he bol ts .
T orque: 5 Nm 11.
Inst all t he engi ne RH mount bracket bol ts .
T orque: M12 80 Nm M10
60 Nm 12.
Inst all t he RH engine mount .
Refer t o: Engi ne Mount RH (303-01B Engi ne - TD4 2.2L Di esel ,
Removal and Ins tall ati on).
13.
Inst all t he thermost at.
14.
Page 868 of 3229
Refer t o: Thermos tat (303-03B Engi ne Cool ing - TD4 2.2L Di es el,Removal and Ins tall ati on).
Inst all t he camshaft s .
Refer t o: Camshafts (303-01B Engine - TD4 2.2L Dies el, Removaland Inst all at ion).
15.
Inst all t he exhaus t manifol d.
Refer t o: Exhaus t Mani fol d (303-01B Engi ne - TD4 2.2L Di esel ,Removal and Ins tall ati on).
16.
Connect t he batt ery ground cable and ins tall t he cover.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
17.
Page 869 of 3229
Publi s hed: 11-May-2011
Engine - TD4 2.2L Diesel - Oil Pan
Removal and Inst all ati on
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
1. W ARNING: Make sure t o s upport the vehicle wit h axle
s tands .
Rais e and s upport t he vehi cl e.
1.
Drai n t he engi ne oil .
Refer t o: Engi ne Oil Draining and Fi lli ng (303-01B Engi ne - TD4 2.2L
Di es el, General Procedures ).
2. 3.
T orque:
9 Nm 4.
For seal ant i nformat ion, refer to the engine specificat ion secti on.
Refer t o: Specificati ons (303-01B Engine - TD4 2.2L Di es el,
Speci fi cat ions ).
5.
Page 870 of 3229
6.
Installation
To i nst all , revers e t he removal procedure.1.
Page 871 of 3229
Stage 1:
Stage 2: Publi s hed: 11-May-2011
Engine - TD4 2.2L Diesel - Oil Pump
Removal and Inst all ati on
Removal
1. W ARNING: Make sure t o s upport the vehicle wit h axle
s tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he oil pan.
Refer t o: Oil Pan (303-01B Engi ne - TD4 2.2L Dies el , Removal and
Inst all at ion).
2. 3. CAUTION: Not e the fi tt ed posi ti on of the
component pri or to removal.
• NOTE: The s houl dered bolt i n pos it ion 1 l ocat es the
oil pump.
3.
Installation 1.
CAUTIONS: Make s ure that t he mat ing faces are clean and
free of foreign mat eri al. Make s ure that t hes e component s are ins tal led t o
t he noted removal pos it ion.
• NOTE: The s houl dered bolt i n pos it ion 1 l ocat es the
oil pump.
Tight en the bol ts evenly i n 2 s t ages to t he s equence
s hown.
T orque: 7 Nm 9 Nm1.
Inst all t he oil pan.
Refer t o: Oil Pan (303-01B Engi ne - TD4 2.2L Dies el , Removal and
Inst all at ion).
2.
Page 872 of 3229
Publi s hed: 11-May-2011
Engine - TD4 2.2L Diesel - Oil Cooler
Removal and Inst all ati on
Removal
Di sconnect t he bat t ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
1.
2. W ARNING: Make sure t o s upport the vehicle wit h axles tands .
Rais e and s upport t he vehi cl e.
2.
Drai n t he cool ant .
Refer t o: Cool ing Sys tem Drai ni ng, Fi lli ng and Bleeding (303-03BEngine Cooli ng - TD4 2.2L Di esel , General Procedures ).
3.
Remove t he air condi ti oni ng (A/C) compres sor.
Refer t o: Air Condi ti oning (A/C) Compres s or - TD4 2.2L Di esel(412-01 Cli mate Cont rol , Removal and Ins t allat ion).
4.
Remove t he thrott le body.
Refer t o: Thrott le Body (303-04B Fuel Chargi ng and Controls - TD42.2L Dies el , Removal and Inst all at ion).
5.
Di sconnect t he engi ne oil pres s ure (EOP) s ens orelectrical connect or.6.
7.