Page 1681 of 3229
Publi s hed: 11-May-2011
Climate Control - Plenum Chamber
Removal and Inst all ati on
Removal
Remove t he RH wi per arm.
Refer t o: W i per Pivot Arm (501-16 W ipers and W ashers, Removaland Inst all at ion).
1.
Repeat t he above procedure for t he other wi per arm.2.
3.
4.
5. W ARNING: Thi s s tep requi res t he aid of anot her t echni ci an.
Remove t he plenum chamber panel.
5.
6. NOTE: Do not dis ass embl e further if t he componenti s removed for acces s onl y.6.
Page 1682 of 3229
Publi s hed: 11-May-2011
Climate Control - Thermostatic Expansion Valve
Removal and Inst all ati on
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
Di sconnect t he bat t ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
1.
Recover t he A/C refrigerant .
Refer t o: Air Condi ti oning (A/C) Sys tem Recovery, Evacuati on and Charging (412-00 Cl imat e Control Sys t em - General Informat ion,
General Procedures).
2.
Remove t he plenum chamber panel.
Refer t o: Plenum Chamber (412-01 Cl imat e Control, Removal and
Inst all at ion).
3. 4.
CAUTIONS: Make s ure that all openings are sealed. Us e new
blanking caps. Lubri cat e t he new s eals wi th cl ean refrigerant oi l.
• NOTE: Inst all new O-ring s eals .
T orque: 9 Nm 4.
T orque:
4 Nm 5.
Installation To i nst all , revers e t he removal procedure.
1.
Page 1683 of 3229

Publi s hed: 11-May-2011
Climate Control - EvaporatorLHD AWD
Removal and Inst all ati on
Removal
• NOTE: The removal of thi s component involves cut t ing an apert ure in t he evaporator hous i ng wall and cutt ing t hrought he high and l ow pres s ure A/C l ines. A s ervice repai r ki t is s uppli ed to cover thi s procedure.
Di sconnect t he bat t ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
1.
Recover t he A/C refrigerant .
Refer t o: Air Condi ti oning (A/C) Sys tem Recovery, Evacuati on andCharging (412-00 Cl imat e Control Sys t em - General Informat ion,General Procedures).
2.
Remove t he plenum chamber panel.
Refer t o: Plenum Chamber (412-01 Cl imat e Control, Removal andInst all at ion).
3.
If ins tal led, remove t he anti -t heft alarm horn wit hi nt egral batt ery.4.
5. CAUTION: Make s ure that all openi ngs ares ealed. Use new blanking caps.
Di sconnect t he A/C pipes from t he TXV.
5.
Page 1684 of 3229
6.
Remove t he RH floor cons ole ext ens ion.7.
Remove t he glove compartment .
Refer t o: Glove Compart ment (501-12 Ins trument Panel andConsol e, Removal and Ins t al lat ion).
8.
9.
10.
Page 1685 of 3229
Page 1686 of 3229
Remove t he CJB bracket .14.
Remove t he 3 s pri ng cl ips .Releas e t he 4 plas t ic cli ps .
15.
Remove t he lower cover.Pos it ion t he upper cover as ide for acces s.
16.
Page 1687 of 3229
Cut t he A/C pi pes at the marked posi ti on.17.
18.
Guide the cut evaporat or pipes through the bulkhead s ot hat approximately 20mm i s vis ibl e in the enginecompart ment.
19.
Page 1688 of 3229
Remove t he evaporat or pi pes.20.
21.
22.