Page 2249 of 3229
Publi s hed: 11-May-2011
Glass, Frames and Mechanisms - Front Door Window Regulator and Motor
Removal and Inst all ati on
Special T ool(s) 501-114
Releas e Lever, Door Glas s
Removal
• NOTE: If pos s ible, l ower t he wi ndow glas s by approximat el y one t hird of it s travel .
Di sconnect t he bat t ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
1.
Remove t he front door s peaker.
Refer t o: Front Door Speaker (415-01 Informat ion and Ent ert ainment
Syst em, Removal and Ins tall ati on).
2. Carefully remove t he outer wais t s eal.
3. Releas e t he door wi ndow glas s from the wi ndow li ft
mechani s m. Rais e t he glas s and s ecure it t o t he t op of
t he door frame.
Speci al Tool (s ): 501-114 4.
Page 2250 of 3229
Remove t he glas s guide channel.5.
Remove t he front door cont rol module.6.
Remove t he window mot or and regulat or as s embly.7.
Installation
Inst all t he window mot or and regulat or as s embly. Tighten the nut sand t he bolt s.1.
Page 2251 of 3229
T orque:
10 Nm Inst all t he door control modul e.
2.
Inst all t he glas s guide channel and li ning. Ti ghten t he bolt .
T orque: 10 Nm 3.
Secure t he door wi ndow glas s t o t he window l ift mechanis m.
4.
Inst all t he out er wais t s eal and s ecure wi th the Torx s crew.
5.
Inst all t he front door s peaker.
Refer t o: Front Door Speaker (415-01 Informat ion and Ent ert ainment
Syst em, Removal and Ins tall ati on).
6.
Connect t he batt ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
7.
Page 2252 of 3229
Publi s hed: 11-May-2011
Glass, Frames and Mechanisms - Rear Door Window Regulator and Motor
Removal and Inst all ati on
Special T ool(s) 501-114
Releas e Lever, Door Glas s
Removal
• NOTE: If pos s ible, l ower t he wi ndow glas s by approximat el y one t hird of it s travel .
Di sconnect t he bat t ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
1.
Remove t he rear door modul e.
Refer t o: Rear Door Module (RDM) (419-10 Mult ifunct ion Electronic
Modules , Removal and Ins t allat ion).
2. Carefully remove t he outer wais t s eal.
3.
Page 2253 of 3229
Releas e t he door wi ndow glas s from the wi ndow
l ift mechanis m. Rais e t he glas s and s ecure i t to
t he top of t he door frame.
Speci al Tool (s ): 501-114 4.
Secure t he glas s t o the top of t he frame.
5.
Page 2254 of 3229
Remove t he window mot or and regulat or
as sembl y. Rotat e t he as sembl y wit hin the door through 90
degrees and remove the upper edge from t he
apert ure firs t. 6.
Installation Inst all t he window mot or and regulat or as s embly. Tighten the nut s
and t he bolt s.
T orque: 10 Nm 1.
Secure t he door wi ndow glas s t o t he window l ift mechanis m.
2.
Inst all t he out er wais t s eal and s ecure wi th the Torx s crew.
3.
Inst all t he rear door modul e.
Refer t o: Rear Door Module (RDM) (419-10 Mult ifunct ion Electronic
Modules , Removal and Ins t allat ion).
4.
Connect t he batt ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
5.
Page 2255 of 3229
Publi s hed: 11-May-2011
Glass, Frames and Mechanisms - Driver Door Window Control Switch
Removal and Inst all ati on
Removal
Di sconnect t he bat t ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
1.
Remove t he front door t ri m panel.
Refer t o: Front Door Trim Panel (501-05 Int eri or Trim andOrnament ati on, Removal and Ins tal lat ion).
2.
Remove t he 2 s crews .Releas e t he 5 cli ps .
3.
Installation
To i nst all , revers e t he removal procedure.1.
Page 2256 of 3229
Publi s hed: 11-May-2011
Glass, Frames and Mechanisms - Passenger Door Window Control Switch
Removal and Inst all ati on
Removal
Di sconnect t he bat t ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
1.
Remove t he rear door t rim panel.
Refer t o: Rear Door Tri m Panel (501-05 Int erior Tri m andOrnament ati on, Removal and Ins tal lat ion).
2.
3.
Installation
To i nst all , revers e t he removal procedure.1.