Page 553 of 3229
23. CAUTION: Only us e new fl uid from a s ealed container.
Refi ll and bleed t he power st eeri ng.
Refer t o: Power St eering Sys tem Bleeding (211-00 St eering Sys tem -
General Informat ion, General Procedures ).
23.
Page 554 of 3229
Publi s hed: 11-May-2011
Power Steering - Power Steering PumpI6 3.2L Petrol
Removal and Inst all ati on
Removal
Remove t he cover and dis connect the bat tery ground cabl e.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
1.
Remove t he engi ne cover.
Refer t o: Engi ne Cover - I6 3.2L Pet rol (501-05 Int eri or Trim andOrnament ati on, Removal and Ins tal lat ion).
2.
Remove t he bat t ery t ray.
Refer t o: Bat t ery Tray (414-01 Bat tery, Mount ing and Cables ,Removal and Ins tall ati on).
3.
Remove t he air cleaner as s embly.
Refer t o: Air Cleaner (303-12A Intake Ai r Dis tribut ion and Fil tering -I6 3.2L Pet rol, Removal and Ins t al lat ion).
4.
Siphon t he fl uid from t he power s t eering res ervoi r.5.
Remove t he A/C compress or, l ower support bracket.6.
Us ing s uit able t ools , rel eas e t he acces s ory drive beltt ens i on.7.
Page 555 of 3229
8. CAUTION: Be prepared to col lect escapingfluids .
• NOTE: Make s ure that all openi ngs are s ealed.
Di sconnect t he power s t eering flui d li nes .
8.
Releas e t he power s t eering pump support bracket.9.
Remove the coolant pump drive ret aini ng screws.10.
Page 556 of 3229

11.
NOTE: Note t he orientat ion of t he cool ant pump
dri ve for i nst all at ion.
Remove t he power s t eering pump.
11.
Installation 1. CAUTION: Make s ure that the coolant pump drive i s located
t o t he ret aining s pri ng.
• NOTE: Make s ure that t he coolant pump drive i s ins t al led t o t he
noted pos it ion in t he power st eeri ng pump pulley.
Inst all t he power s t eering pump.
T orque: 25 Nm 1.
Inst all t he cool ant pump drive retai ni ng s crews .
T orque: 10 Nm 2.
3. CAUTIONS: Ext reme cl eanli ness must be exerci sed when handli ng t hes e
component s. A new O-ri ng s eal i s to be ins tal led.
Connect t he power s t eering flui d li nes.
T orque: 27 Nm 3.
Inst all t he acces sory dri ve bel t.
4.
Inst all t he A/C compress or, l ower support bracket.
T orque: 25 Nm 5.
Inst all t he air cleaner as s embly.
Refer t o: Air Cleaner (303-12A Intake Ai r Dis tribut ion and Fil tering -
I6 3.2L Pet rol, Removal and Ins t al lat ion).
6.
Inst all t he bat t ery t ray.
Refer t o: Bat t ery Tray (414-01 Bat tery, Mount ing and Cables ,
Removal and Ins tall ati on).
7.
Inst all t he engi ne cover.
Refer t o: Engi ne Cover - I6 3.2L Pet rol (501-05 Int eri or Trim and
Ornament ati on, Removal and Ins tal lat ion).
8.
Fil l and bl eed the power s t eering s ys tem.
Refer t o: Power St eering Sys tem Bleeding (211-00 St eering Sys tem -
General Informat ion, General Procedures ).
9.
Connect t he batt ery ground cable and ins tall t he cover.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
10.
Page 557 of 3229

Publi s hed: 11-May-2011
Power Steering - Power Steering PumpTD4 2.2L Diesel
Removal and Inst all ati on
Removal
CAUTION: Always pl ug any open connect ions t o prevent cont aminati on.
Remove t he engi ne cover.
Refer t o: Engi ne Cover - TD4 2.2L Dies el (501-05 Interior Tri m andOrnament ati on, Removal and Ins tal lat ion).
1.
Remove t he acces sory dri ve bel t.
Refer t o: Acces sory Dri ve Belt (303-05B Acces sory Drive - TD4 2.2LDi es el, Removal and Ins tal lat ion).
2.
3. W ARNING: Power s t eering fluid is ext remely fl ammable.Make s ure that power s t eering flui d is not s pil t over t he engine andt hat t he power s teeri ng fl uid reservoi r cap is s ealed.
Siphon t he fl uid from t he power s t eering res ervoi r.
3.
4. CAUTIONS:
Be prepared t o collect es caping oi l.
Make s ure that t he area around the component i sclean and free of foreign materi al.
Al ways pl ug any open connect ions t o preventcont ami nat ion.
Pos it ion a contai ner t o coll ect t he oil s pill age.
4.
5. CAUTIONS:
Be prepared t o collect es caping oi l.
Make s ure that t he area around the component i sclean and free of foreign materi al.
Al ways pl ug any open connect ions t o preventcont ami nat ion.
5.
Page 558 of 3229
6.
CAUTIONS: Be prepared t o collect es caping fuel.
Make s ure that t he area around the component i s
clean and free of foreign materi al. Al ways pl ug any open connect ions t o prevent
cont ami nat ion.
6. 7.
8.
Installation 1. CAUTION: Make s ure that the mati ng faces are cl ean and
free of foreign mat eri al.
Inst all t he power s t eering pump.
T orque: 24 Nm 1.
Connect t he fuel li nes .
2.
Connect t he high-press ure power s t eering l ine t o t he power st eeri ng
pump.
T orque: 20 Nm 3.
Connect t he power s t eering res ervoir t o power s t eering pump hos e.
4.
Inst all t he acces sory dri ve bel t.
5.
Page 559 of 3229
Refer t o: Acces sory Dri ve Belt (303-05B Acces sory Drive - TD4 2.2LDi es el, Removal and Ins tal lat ion).
Inst all t he engi ne cover.
Refer t o: Engi ne Cover - TD4 2.2L Dies el (501-05 Interior Tri m andOrnament ati on, Removal and Ins tal lat ion).
6.
Fil l and bl eed the power s t eering s ys tem.
Refer t o: Power St eering Sys tem Bleeding (211-00 St eering Sys tem -General Informat ion, General Procedures ).
7.
Page 560 of 3229

Publi s hed: 11-May-2011
Power Steering - Steering Gear
Removal and Inst all ati on
Removal
1. W ARNING: Make sure t o s upport the vehicle wit h axle
s tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he front road wheels and t ires.
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal and
Inst all at ion).
2.
Remove t he front subframe as s embly.
Refer t o: Front Subframe (502-00 Uni -Body, Subframe and Mount ing
Syst em, Removal and Ins tall ati on).
3. Remove t he s teeri ng gear.
4.
Installation Inst all t he s teeri ng gear.
T orque: 105 Nm 1.
Inst all t he front subframe.
Refer t o: Front Subframe (502-00 Uni -Body, Subframe and Mount ing
Syst em, Removal and Ins tall ati on).
2.
Inst all t he wheel s and t ires .
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal and
Inst all at ion).
3.
Refi ll and bleed t he power st eeri ng.
Refer t o: Power St eering Sys tem Bleeding (211-00 St eering Sys tem -
General Informat ion, General Procedures ).
4.
Us ing onl y four wheel al ignment equi pment approved by Land Rover,
check and adjus t t he wheel al ignment.
5.