
Publi s hed: 11-May-2011
Interior Lighting - Interior Lighting
Diagnosi s  and Tes ti ng
Principles of Operation
For a detail ed descripti on of the interior li ght ing sys tem, refer t o t he rel evant Des cript ion and Operat ion s ecti on in theworks hop manual .REFER to: Interior Lighti ng (417-02 Int erior Light ing, Descri pti on and Operat ion).
Inspection and Verification
CAUTION: Di agnos is  by s ubs ti tut ion from a donor vehicle is  NO T acceptabl e. Subs ti tut ion of cont rol  modules  doesnot guarant ee confirmat ion of a faul t, and may als o caus e addit ional fault s  i n t he vehi cl e being t est ed and/or t he donorvehi cl e.
1. Verify t he cus t omer concern.1.
2. Vis ually ins pect  for obvious  s igns  of mechani cal  or electrical damage.2.
Visual InspectionMechanicalElectrical
BulbsFus es/rel ays  (refer to electrical gui de)W iring harnes sCorrect engagement of elect rical  connect orsLoos e or corroded connecti ons
3. If an obvious  cause for an obs erved or report ed concern is  found, correct  t he caus e (if pos s ible) beforeproceeding t o t he next  s t ep.3.
4. If t he caus e is  not vis ually evi dent , check for Di agnos ti c Trouble Codes  (DTCs) and refer t o t he DTC Index.4.
DTC Index
• NOTE: If the control modul e or a component  i s s us pect and the vehicle remains  under manufacturer warrant y, refer t o theW arranty Pol icy and Procedures  manual (s ect ion B1.2), or determine i f any pri or approval programme is  in operat ion, pri ort o the ins tall ati on of a new module/component.
• NOTE: Generic scan t ool s  may not  read the codes li st ed, or may read only fi ve digit  codes . Mat ch the five di git s from t hes can tool to the firs t fi ve di git s of the seven digi t code l is ted to ident ify t he faul t (t he las t  t wo digi ts  gi ve ext rainformat ion read by the manufact urer-approved diagnost ic s ys tem).
• NOTE: W hen performing volt age or res is t ance t est s , always use a digi tal mult imeter (DMM) accurat e t o t hree deci malplaces and wit h a current cal ibrat ion cert ificate. W hen tes ti ng res i st ance, always  take the res is tance of the DMM l eads  i ntoaccount.
• NOTE: Check and recti fy bas ic faul ts  before beginni ng diagnos t ic rout ines  i nvol vi ng pinpoint t es t s.
• NOTE: If DTCs  are recorded and, aft er performi ng the pi npoi nt  tes ts , a fault  is  not  present , an int ermi tt ent  concern maybe t he caus e. Always  check for loose connect ions  and corroded terminals .
DT CDescriptionPossible CauseActionB113C11Hazard swit ch ill uminat ion -ci rcuit  s hort  t o groundHazard s wi tch i lluminati oncircui t - s hort to groundRefer t o elect rical circuit  di agrams  and checkhazard s wi tch i llumi nati on ci rcuit  for short toground
B113C15Hazard swit ch ill uminat ion -ci rcuit  s hort  t o power oropen
Hazard s wi tch i lluminati oncircui t - s hort to power, opencircui t
Refer t o elect rical circuit  di agrams  and checkhazard s wi tch i llumi nati on ci rcuit  for short topower, open circui t
B1D1312Interior Lights  #1 Circui t -ci rcuit  s hort  t o powerInst rument  panel i nterior li ght scircui t - s hort to powerRefer t o elect rical circuit  di agrams  and checki ns t rument  panel  i nterior li ght s  circui t fors hort  t o power
B1D1314Interior Lights  #1 Circui t -ci rcuit  s hort  t o ground oropen
Inst rument  panel i nterior li ght scircui t - s hort to ground, opencircui t
Refer t o elect rical circuit  di agrams  and checki ns t rument  panel  i nterior li ght s  circui t fors hort  t o ground, open ci rcuit
B1D1A12Interior Lights  Circuit  'C' -ci rcuit  s hort  t o powerRoof cons ole i nterior li ght scircui t - s hort to powerRefer t o elect rical circuit  di agrams  and checkroof panel interior li ghts  circui t for s hort  t opowerB1D1A14Interior Lights  Circuit  'C' -ci rcuit  s hort  t o ground oropen
Roof cons ole i nterior li ght scircui t - s hort to ground, opencircui t
Refer t o elect rical circuit  di agrams  and checkroof panel interior li ghts  circui t for s hort  t oground, open ci rcuit
U025200Los t Communicati on W i thLi ght ing Cont rol Modul e -Rear 'B'
Lost  communi cat ion wi th trailermoduleCarry out t he ass ociated net work t es t fort his  DTC us i ng the manufact urer approveddiagnos ti c sys t em
U201011Swi tch Ill uminat ion - circui ts hort  t o groundSwit ch il lumi nat ion ci rcuit  -s hort  t o groundRefer t o elect rical circuit  di agrams  and checks wit ch il lumi nat ion ci rcuit  for short  to ground 

41
Keys and remote controls
R
USING THE REMOTE CONTROL
Remote control
Note:  The operational range of the remote  
control will vary considerably depending on 
atmospheric conditions and interference from  
other transmitting devices. 
The vehicle is supplied with two remote  
controls, but up to six can be programmed to  
the vehicle at any one time. 
1.  Unlock.  
2.  Lock.  
3.  Tailgate release.  
4.  Approach lighting.  
5.  Emergency alarm.  
6.  Key blade release tab. 
7.  Key blade. 
Unlocking
Press briefly to unlock the vehicle,  
and deactivate the alarm. The 
hazard warning lamps will flash  
twice to indicate that   the vehicle is unlocked  
and the alarm has been   deactivated. The  
interior lamps will illuminate to assist entry to  
the vehicle. 
Note:   The fuel filler flap can only be opened  
when the vehicle is unlocked. 
Single/Multi-  point entry 
When you press the unlock button your vehicle  
will unlock in one of two ways: 
1.  Unlock the driver's door, fuel filler flap, and  
tailgate only. A second   press is required to  
unlock the remaining doors. 
2.  Unlock all doors, fuel filler flap, and the  
tailgate. 
This security feature unlocks only the driver’s  
door and tailgate. It   can be disabled on  
individual remote controls by unlocking the  
vehicle then simultaneously pressing and 
holding the lock and unlock buttons for three  
seconds. The vehicle will   lock and then unlock  
in the currently selected   mode and the hazard  
warning lights will flas  h twice to confirm the  
change. You can now unlock all doors with a  
single press. Repeating the procedure will 
re-enable Single point entry. 
Global opening 
Press and hold the unlock button for three  
seconds to unlock the ve  hicle and open all of  
the windows.
WARNING 
Never leave the remote control in the  
vehicle if children or animals are also  
left in the vehicle. The vehicle's systems and  
remote control functions   could be operated,  
which may result in injury.
2
E80909
451
3
6
7 

45
Alarm
R
AlarmARMING THE ALARM
The engine is automatically  
immobilised when the remote  
control is removed from the starter 
control unit. The alarm system is automatically  
armed when the remote lock button is pressed.  
The hazard lamps will flash to indicate that the  
alarm is armed.
Full alarm
To set full alarm protection ensure that all the 
windows and the sunroof are closed. Then  
press the lock button twice within three 
seconds. The hazard warn  ing lights will flash  
twice to confirm the alarm state. 
Once fully armed the   alarm will sound if :- 
•  the bonnet, tailgate, or a door are opened. 
•  movement is detected within the vehicle  
interior. 
•  a window, front or rear windscreen, or  
sunroof glass are broken. 
•  the vehicle is raised or tilted. 
•  the vehicle battery is disconnected. 
•  an attempt is made to  disconnect the alarm  
siren. 
Note:   If the alarm is armed and a window or the  
sunroof are left open the alarm will sound due  
to movement of air currents.
Partial alarm
To set partial alarm protection, briefly press the 
lock button once. The hazard warning lights 
will flash once to confirm the alarm state. 
Once partially armed the alarm will sound if :- 
•  the bonnet, tailgate, or a door are opened. 
•  the vehicle battery is disconnected. 
•  an attempt is made to  disconnect the alarm  
siren.  Note:  
This setting should be used in  
circumstances such as travelling on a ferry,  
when pets are to be left in the vehicle, when a 
window must be left open etc
Alarm indicator
The alarm status is disp  layed by the indicator.  
•  Indicator off - alarm disarmed. 
•  Indicator flashes once  per second - alarm  
is armed and engine immobilised. 
•  Indicator flashes rapidly - the alarm has  
been triggered. 
Note:   The alarm status in dicator will flash  
rapidly when the alarm has been disarmed, but 
the remote has not been docked.
E81141 

Lighting
76
L
INTERIOR LAMPS
1. Sun visor lamps. Sw itch on or off as  
required using the switch. 
2.  Map reading/interior lamps. The switch  
allows them to be turn  ed on, off, or set to  
operate when the doors are opened. 
3.  Luggage compartment lamp.  
Automatically illuminates when the doors  
are opened. 
4.  Puddle lamps. Automatically illuminate  
when the doors are opened. 
5.  Glove box lamp. Auto matically illuminates  
when the glove box is opened. 
6.  Footwell lamps. Auto matically illuminate  
when the doors are opened.APPROACH LAMPS
The approach lamp feature turns on the 
parking lamps, indica  tor lamps, door mirror  
lamps, number plate lamps,   interior lamps, and  
puddle lamps remotely  . This feature is  
activated with the remote control.  See   USING  
THE REMOTE CONTROL   (page 41). 
The length of time which the lights  
remain on can be adjusted by your  
Land Rover Dealer/Authorised 
Repairer.
3
2
4
1
2
6
4
1
5
61
2
E83602 

Fuses
200
L
Fuse number Rating (Amps) Fuse co lour Circuits protected 
F1 5 tan Rain sensor 
F2 10 red SRS
F3 5 tan ABS 
F4 5 tan Instrument pack -   Accelerator pedal - Light  
Switch Module 
F5 - - -
F6 15 blue Audio unit 
F7 7.5 brown Steering wheel controls 
F8 5 tan Instrument pack
F9 15 blue Headlamp main beam 
F10 15 blue Sunroof 
F11 7.5 brown Reverse lights and interior   mirror dip 
F12 - - - 
F13 15 blue Front fog lamps
F14 15 blue Screen wash 
F15 - - - 
F16 - - -
F17 7.5 brown Interior lighting 
F18 - - - 
F19 5 tan Electric seat adjustment
F20 15 blue Rear wiper 
F21 5 tan Alarm 
F22 20 yellow Fuel pump
F23 20 yellow Steering column lock 
F24 - - - 
F25 10 red Tailgate - Fuel filler flap
F26 5 tan Diagnostic socket and   alarm 
F27 5 tan Start button and climate   control 
F28 5 tan Brake lights 

414-01 BATTERY, MOUNTING AND CABLES
Central junction box 
FREELANDER 2 - LR2 - VIN: 000201 onwards  (LHD)  (03 / 06) 55
BU-GN,0.75,1320
BU-GN,0.5,2140BN-YE,0.5,1970
VT-OG,0.5,2115VT-OG,0.5,2225BN-YE,0.5,2115
VT-OG,0.5,2245BN,0.5,2245BN-BU,1.5,2815GN-OG,0.75,2815BN-WH,0.5,945
BU,1.5,615BK,0.5,2310BU-GY,0.5,1661BU-GY,0.5,830
BU,0.75,1550YE-VT,0.5,6940BU-GY,0.5,760
BU-GN,0.75,945
GY-OG,0.75,6490VT-GN,0.75,6490BU-GN,0.75,1495
GN,0.5,4870
BK,0.5,1585
VT-BN,0.75,2245VT-WH,0.5,4415
VT-BN,0.5,2225
(PETROL)VT-BN,0.5,2115
(DIESEL)
BU-OG,0.5,2705VT-BN,0.75,4425YE,0.5,2550YE-OG,0.75,6940BN,0.5,6940BU,0.5,5855
BK,0.5,1585BK,0.75,2390BK,0.5,2310
WH,0.5,795GN-VT,0.5,4120
BK,0.5,1735BK,0.5,1735
Central junction-box (P101)
Heater-PTC (H137)Centre facia (S425) 
Switch pack-module (ECM) (D131)
Engine control-module (ECM) (D131)
Engine control-
FET-
C11P-9 C11N-9C11P-3 C11N-3
FET-WAKE UP  FET-ECMFET-
tail door switch (A155) 
Lamp-Number plate and-Headlamp-LH (A101)Front-RH (B135) 
Lamp-Footwell-Front (B100)
Lamp-Interior-Front-LH (B136)
Lamp-Footwell-A 
Sheet6
C44M-8 C44N-8
LIGHTS 
FET-INTERIORFET-PLATE LAMP
FET-NUMBER
beam-LH FET-Dip-
Tail lamp unit-LH (A139)Front-LH (A121) 
Lamp-Side repeater-
FET-FET-
locking-Rear-LH (M167) 
Motor-Central door-
Module (CEM) (D316) 
Central Electronics
C27B-6
C27A-6
Auxiliary junction box (P107)Switch-Brake diagnostic (S473)module (ECM) (D131) 
Engine control-module (ECM) (D131)
Engine control-Stop lamp switch (S215)tail door switch (A155)
Lamp-Number plate and-Switch-Bonnet (S224)Upper (M255)
Motor-CDL-Tailgate-locking-Rear-RH (M166)
Motor-Central door-
EARTH2 
Sheet6
BATTA (3)
Sheet4
C11N-4 C11P-4
C44N-4 C44M-4C44N-2 C44M-2C28A-6
C27B-6
locking-Driver (M236) 
Motor-Central door-locking-Passenger (M237)
Motor-Central door-
EARTH1 
Sheet1
BATTA (2)
Sheet2
C26A-1 C26B-1C25A-1 C25B-1
C2HP01E-2C1E104H-D1C2PL13-3C1E104H-C1C1E109B-14
C1BP02C-39C1BP02C-41 
NOT USED (V101)C1BP02A-8C1BP02C-8C1BP02A-44
C9LN28B-1C4LS04A-3C3LN39-2C3LN38-2C1LF08A-2C1LF08A-5C1LF08A-4
C1BP02H-1
NOT USED (V101)
S9LN33
C1BP02H-20C1BP02C-19C1BP02B-52
S2LN38
C1BP02C-37C1BP02A-13C1BP02A-76
C4LS35A-4C4LS35A-3C1LS13-1
S1LS21
C1BP02B-36C1BP02B-50C1BP02A-19
C7PL71-4
C1BP02B-9
STOP SWITCH SIG
PTC HEATERFUEL PUMP ONHAZARD SWITCHHAZARD ILLUMECM WAKE UP
BRAKE DIAG
C1BP02B-12
C2CB08-1C1E104H-G3C1E109B-30
LICENSE PLATE SUPPLYSIDE MARKERS(fl) 
(not used)CONVENIENCE LIGHTINTERIOR LIGHT
DIMMING LS SUPPLY
C1BP02A-23
HOOD AJAR SW
C1BP02A-37C1BP02B-54
RR WIPER RELAY
C1BP02B-44
DIPPED BEAM LEFT
TAILGATE AJARTAIL GATE RELEASE
C1BP02B-10C1BP02B-13
RR AJARRL AJAR
C1BP02B-8
C1RT17A-1C2CA29-2C4BR02A-26C4LS04A-1C4PL17A-3C7PL71-4
DI LEFT SUPPLYPOSITION LIGHT LEFT SUPPLY
FR AJAR
C1BP02B-6
FL AJAR
C1BP02B-7
C6PL64-4C5PL63-4 

414-01 BATTERY, MOUNTING AND CABLES
Central junction box 
FREELANDER 2 - LR2 - VIN:   000201 onwards  (RHD) (03 / 06) 55
BU-GN,0.75,1320
BU-GN,0.5,2140BN-YE,0.5,1970
VT-OG,0.5,2115VT-OG,0.5,2225BN-YE,0.5,2115
VT-OG,0.5,2245BN,0.5,2245BN-BU,1.5,2815GN-OG,0.75,2815BN-WH,0.5,945
BU,1.5,615BK,0.5,2310BU-GY,0.5,1661BU-GY,0.5,830
BU,0.75,1550YE-VT,0.5,6940BU-GY,0.5,760
BU-GN,0.75,945
GY-OG,0.75,6490VT-GN,0.75,6490BU-GN,0.75,1495
GN,0.5,4870
BK,0.5,1585
VT-BN,0.75,2245VT-WH,0.5,4415
VT-BN,0.5,2225
(PETROL)VT-BN,0.5,2115
(DIESEL)
BU-OG,0.5,2705VT-BN,0.75,4425YE,0.5,2550YE-OG,0.75,6940BN,0.5,6940BU,0.5,5855
BK,0.5,1585BK,0.75,2390BK,0.5,2310
WH,0.5,795GN-VT,0.5,4120
BK,0.5,1735BK,0.5,1735
Central junction-box (P101)
Heater-PTC (H137)Centre facia (S425) 
Switch pack-module (ECM) (D131)
Engine control-module (ECM) (D131)
Engine control-
FET-
C11P-9 C11N-9C11P-3 C11N-3
FET-WAKE UP  FET-ECMFET-
tail door switch (A155) 
Lamp-Number plate and-Headlamp-LH (A101)Front-RH (B135) 
Lamp-Footwell-Front (B100)
Lamp-Interior-Front-LH (B136)
Lamp-Footwell-A 
Sheet6
C44M-8 C44N-8
LIGHTS 
FET-INTERIORFET-PLATE LAMP
FET-NUMBER
beam-LH FET-Dip-
Tail lamp unit-LH (A139)Front-LH (A121) 
Lamp-Side repeater-
FET-FET-
locking-Rear-LH (M167) 
Motor-Central door-
Module (CEM) (D316) 
Central Electronics
C27B-6
C27A-6
Auxiliary junction box (P107)Switch-Brake diagnostic (S473)module (ECM) (D131) 
Engine control-module (ECM) (D131)
Engine control-Stop lamp switch (S215)tail door switch (A155)
Lamp-Number plate and-Switch-Bonnet (S224)Upper (M255)
Motor-CDL-Tailgate-locking-Rear-RH (M166)
Motor-Central door-
EARTH2 
Sheet6
BATTA (3)
Sheet4
C11N-4 C11P-4
C44N-4 C44M-4C44N-2 C44M-2C28A-6
C27B-6
locking-Driver (M236) 
Motor-Central door-locking-Passenger (M237)
Motor-Central door-
EARTH1 
Sheet1
BATTA (2)
Sheet2
C26A-1 C26B-1C25A-1 C25B-1
C2HP01E-2C1E104H-D1C2PL13-3C1E104H-C1C1E109B-14
C1BP02C-39C1BP02C-41 
NOT USED (V101)C1BP02A-8C1BP02C-8C1BP02A-44
C9LN28B-1C4LS04A-3C3LN39-2C3LN38-2C1LF08A-2C1LF08A-5C1LF08A-4
C1BP02H-1
NOT USED (V101)
S9LN33
C1BP02H-20C1BP02C-19C1BP02B-52
S2LN38
C1BP02C-37C1BP02A-13C1BP02A-76
C4LS35A-4C4LS35A-3C1LS13-1
S1LS21
C1BP02B-36C1BP02B-50C1BP02A-19
C7PL71-4
C1BP02B-9
STOP SWITCH SIG
PTC HEATERFUEL PUMP ONHAZARD SWITCHHAZARD ILLUMECM WAKE UP
BRAKE DIAG
C1BP02B-12
C2CB08-1C1E104H-G3C1E109B-30
LICENSE PLATE SUPPLYSIDE MARKERS(fl) 
(not used)CONVENIENCE LIGHTINTERIOR LIGHT
DIMMING LS SUPPLY
C1BP02A-23
HOOD AJAR SW
C1BP02A-37C1BP02B-54
RR WIPER RELAY
C1BP02B-44
DIPPED BEAM LEFT
TAILGATE AJARTAIL GATE RELEASE
C1BP02B-10C1BP02B-13
RR AJARRL AJAR
C1BP02B-8
C1RT17A-1C2CA29-2C4BR02A-26C4LS04A-1C4PL17A-3C7PL71-4
DI LEFT SUPPLYPOSITION LIGHT LEFT SUPPLY
FR AJAR
C1BP02B-6
FL AJAR
C1BP02B-7
C6PL64-4C5PL63-4