2006 LAND ROVER FRELANDER 2 reset

DT CDescriptionPossible CauseAction
C1A63-13Right Rear Ini ti at or -open circuitRi ght rear init iat or ci rcuit -open circui tRefer to electrical ci rcuit diagrams and check right rearinit iat or ci rcuit for open ci rcuit
C1B14-12Sensor s uppl y #1 -circui t short to powerSens or supply #1 circuit -s hort t o powerRefer to electrical ci rcuit diagrams and check s ens ors upply #1 circui t for s hort t o power
C1D18-00Local is ati on fail edTi re press ure monit orl ocal is ati on fai ledCheck for addi ti onal rel ated DTCs and refer t o thi s DTCIndex
C1D21-05W heel module -general si gnal failureSi emens int ernal al gorit hmCarry out the pi npoint t es ts as s oci at ed t o t his DTCusi ng t he manufact urer approved diagnost ic s ys tem
C1D22-49Steering W heelSwit ch Right Module -Int ernal fai lure
St eering wheel s wit ch ri ghtmodul e - int ernal fai lureIns t al l a new was h/wi pe s wit ch, refer t o newmodule/component i nst all at ion not e at t he top of t heDTC IndexC2003-07Steering W heelSwit ch Left Module -Mechani cal Failures
St eering wheel s wit ch leftmodul e - mechani calfail ure
Ins t al l a new i ndi cat or swit ch, refer to newmodule/component i nst all at ion not e at t he top of t heDTC Index
C2003-49Steering W heelSwit ch Left Module -Int ernal fai lure
St eering wheel s wit ch leftmodul e - int ernal fai lureIns t al l a new i ndi cat or swit ch, refer to newmodule/component i nst all at ion not e at t he top of t heDTC Index
C2004-12Headlamp was herrel ay B - circui t s hortt o power
Headlamp washer rel ay Bci rcuit - s hort t o powerRefer to electrical ci rcuit diagrams and check headl ampwasher rel ay B circui t for s hort t o power
C2004-14Headlamp was herrel ay B - circui t s hortt o ground or open
Headlamp washer rel ay Bci rcuit - s hort t o ground,open circui t
Refer to electrical ci rcuit diagrams and check headl ampwasher rel ay B circui t for s hort t o ground, open ci rcuit
P0460-15Fuel Level Sens or A -s hort t o batt ery oropen circuit
Fuel tank unit ci rcuit As hort t o power, openci rcuit
• NOTE: Carry out pi npoi nt tes ts ass ociated wit h t hi sDTC us ing t he manufacturer approved diagnos ti cs ys t em
Refer to the el ect ri cal circui t diagrams and check theci rcuit bet ween the central junct ion box and the fueltank unit ci rcuit (F/P s ensor) for s hort t o power, openci rcuit . Us ing t he manufacturer approved diagnos ti cs ys t em check and i nst all l at es t relevant level ofs oftware t o t he cent ral juncti on box and t he ins trumentpanel clus ter. If t he level of software is correct carryout a batt ery reset
P0462-00Fuel Level Sens or A -no s ubtypeinformat ion
Fuel tank unit ci rcuit As hort t o ground or hi ghres is tance
• NOTE: Carry out pi npoi nt tes ts ass ociated wit h t hi sDTC us ing t he manufacturer approved diagnos ti cs ys t em
Refer to the el ect ri cal circui t diagrams and check theci rcuit bet ween the central junct ion box and the fueltank unit ci rcuit (F/P s ensor) for s hort t o ground. Us ingthe manufact urer approved diagnos t ic s ys tem checkand ins tal l lates t rel evant l evel of software t o t hecent ral juncti on box and the ins trument panel cl ust er.If t he l evel of software i s correct carry out a bat t eryres et
P0604-00Int ernal ControlModule RandomAcces s Memory (RAM)Error
RAM Checks um not correctIns t al l a new CJB, refer t o t he new module/componentins tal lati on note at the t op of the DTC Index
P0605-00Int ernal ControlModule Read Onl yMemory (ROM) Error
ROM Checks um not correctIns t al l a new CJB, refer t o t he new module/componentins tal lati on note at the t op of the DTC Index
P062F-00Int ernal ControlModule Read Onl yMemory (ROM) Error
EEP read back val ue doesnot mat ch wri tt en valueIns t al l a new CJB, refer t o t he new module/componentins tal lati on note at the t op of the DTC Index
P0801-11Revers e inhibi tcont rol circui t - circuits hort t o ground
Revers e i nhi bit controlci rcuit - s hort t o groundRefer to electrical ci rcuit diagrams and check revers einhibi t cont rol ci rcuit for short to ground
P1346-13Fuel Level Sens or B -open circuitFuel tank unit ci rcuit Bs hort t o power, openci rcuit
• NOTE: Carry out pi npoi nt tes ts ass ociated wit h t hi sDTC us ing t he manufacturer approved diagnos ti cs ys t em
Refer to the el ect ri cal circui t diagrams and check theci rcuit bet ween the central junct ion box and the fueltank unit ci rcuit (Fuel eject s ens or) for s hort to power,open ci rcuit . Usi ng t he manufacturer approveddiagnos t ic s ys tem check and ins t al l lat es t relevantlevel of s oft ware to the central junct ion box and theins trument panel clus ter. If t he level of s oftware iscorrect carry out a bat t ery res et
P1348-00Fuel Level Sens or B -no s ubtypeinformat ion
Fuel tank unit ci rcuit Bs hort t o ground• NOTE: Carry out pi npoi nt tes ts ass ociated wit h t hi sDTC us ing t he manufacturer approved diagnos ti cs ys t em
Refer to the el ect ri cal circui t diagrams and check theci rcuit bet ween the central junct ion box and the fuel

DT CDescriptionPossible CauseAction
tank unit ci rcuit (Fuel eject s ens or) for s hort to ground.Us ing t he manufacturer approved diagnost ic sys temcheck and ins t al l lat es t relevant l evel of s oft ware t othe central juncti on box and the i nst rument panelcl ust er. If t he level of s oft ware is correct carry out abat t ery resetP1674-00Control ModuleSoft ware Corrupt edA s oft ware as s ert ion fai ledwit hi n t he moduleLoad the l ates t rel evant level of s oftware usi ng t hemanufacturer approved diagnost ic sys tem
U0001-00High Speed CANCommunicati on BusBus O ffCarry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0010-00Medium Speed CANCommunicati on BusBus O ffCarry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0100-00Lost Communi cat ionW i th ECM/PCM 'A'Los t communicat ion wit hECMCarry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0101-00Lost Communi cat ionwi th TCMLos t communicat ion wit hTCMCarry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0104-00Lost Communi cat ionW i th Speed Cont rolModule
Los t communicat ion wit hs peed cont rol moduleCarry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0126-00Lost Communi cat ionW i th Steeri ng AngleSensor Module
Los t communicat ion wit hs t eering angle s ens orCarry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0129-00Lost Communi cat ionW i th Brake Syst emControl Module
Los t communicat ion wit hABS modul eCarry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0135-00Lost Communi cat ionW i th Different ialControl Module -Front
Los t communicat ion wit hdi fferenti al control modul eCarry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0155-00Lost Communi cat ionW i th Ins t rumentPanel Cl us t er (IPC)Control Module
Los t communicat ion wit hi nst rument clus t erCarry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0156-00Lost Communi cat ionW i th Informat ionCenter "A"
Los t communicat ion wit hi nformati on cent erCarry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0159-00Lost Communi cat ionW i th Parking As s is tControl Module "A"
Los t communicat ion wit hparki ng aid modul eCarry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0164-00Lost Communi cat ionW i th HVAC ControlModule
Los t communicat ion wit hcl imat e cont rol moduleCarry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0166-00Lost Communi cat ionW i th Auxi li ary HeaterControl Module
Los t communicat ion wit hauxil iary heat er cont rolmodul e
Carry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0181-00Lost Communi cat ionW i th Headl ampLevel ling Cont rolModule
Los t communicat ion wit hheadlamp Levell ing controlmodul e
Carry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0199-00Lost Communi cat ionW i th "Door ControlModule A"
Los t communicat ion wit hDriver Door Modul e (DDM)Carry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0200-00Lost Communi cat ionW i th "Door ControlModule B"
Los t communicat ion wit hPas s enger Door Modul e(PDM)
Carry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0208-00Lost Communi cat ionW i th "Seat ControlModule A"
Los t communicat ion wit hPas s enger Seat Modul e(PSM)
Carry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0214-00Lost Communi cat ionW i th Remote Functi onActuati on
Los t communicat ion wit hRemot e Keyles s Entrymodul e
Carry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0231-00Lost Communi cat ionW i th Rain Sens ingModule
Los t communicat ion wit hrain sens ing moduleCarry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0236-00Lost Communi cat ionW i th Column LockModule
Los t communicat ion wit hs t eering column lockmodul e
Carry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0252-00Lost Communi cat ionW i th Lighti ng Cont rolModule - Rear 'B'
Los t communicat ion wit ht rai ler moduleCarry out the as s oci at ed network t es t for this DTCusi ng t he manufact urer approved diagnost ic s ys tem
U0301-00Soft wareIncompati bil it y wit hECM/PCM
ECM dis connect edIncorrect ECM i nst all edCheck el ect ri cal connecti ons to ECM. Check correct ECMis i nst all ed

s peed control '+' and '-' but t ons (dependant on vehi cl e s peci fi cat ion). The HDC Target speed wi ll als o vary depending ont he Terrai n Respons e™ mode sel ect ed.
Duri ng changes of target s peed, the ABS modul e li mit s vehicle decelerat ion and accelerat ion t o -0.5 met ers per s econd
s quared (m/s2) (-1.64 feet per s econd squared (ft/s2)); and +0.5 m/s2 (+1.64 ft/s2) res pect ively.
To provide a s afe t rans it ion from acti ve braking t o brakes off, the ABS module i nvokes a fade out st rat egy that graduall yrel eas es t he braking effort during act ive braking. The fade out s t rat egy occurs i f any of t he fol lowi ng condit ions i s detectedduri ng act ive braki ng:
HDC i s s elected off us i ng the HDC s wit ch.Failure of a component us ed by HDC, but not crit ical t o fade out funct ion.Accelerator pedal pres s ed when t rans mis s ion i s i n neut ral .Brakes overheat .
If fade out is i nvoked becaus e of HDC de-s el ect ion or component failure, the HDC functi on is cancel led by t he ABS module.If fade out is i nvoked becaus e t he accelerator pedal i s pres s ed wit h t he t ransmis s ion i n neut ral , or because of brakeoverheat , t he HDC funct ion remains in s tandby and res umes operati on when t he accelerat or pedal is releas ed or the brakeshave cooled.
The fade out s t rategy i ncreas es t he t arget speed at a cons tant accelerati on rat e of 0.5 m/s2 (1.64 ft/s2), unti l themaximum t arget speed i s reached, or unti l no act ive braki ng is required for 0.5 second. If t he accelerat or pedal is
posi ti oned wit hin t he range t hat infl uences t arget s peed, the accelerat ion rate is increas ed t o 1.0 m/s2 (3.3 ft /s2).
W hen fade out is i nvoked becaus e of component fai lure, a warning chime is sounded and the HDC informat ion i ndi cat orlamp is ext inguis hed. The HDC warning i ndicat or lamp is t hen il lumi nat ed (on low-li ne ins trument cl ust er), or a mes s ageadvi s ing of t he fault i s dis played in the mess age cent er (on hi gh-l ine i ns t rument clus ter).
For addit ional informat ion, refer t o:
Ins trument Clus ter (413-01 Ins t rument Clus t er, Descripti on and Operat ion),Informat ion and Mes s age Cent er (413-08 Informati on and Mes sage Cent er, Descripti on and Operat ion).
W hen fade out is i nvoked becaus e of brake overheat, on vehicles wi th the hi gh-li ne ins t rument clus ter, a mes sage advis ingt hat HDC is t emporarily unavail abl e is di s pl ayed. On vehicles wit h t he low-line ins trument cl us t er, t he HDC warningindicat or l amp flas hes . At t he end of fade out, t he HDC informati on indicat or flas hes. The flas hing warni ng and informat ionindicat or l amps, and/or di spl ayed mes s age cont inue whi le HDC remai ns sel ect ed, unt il t he brakes have cooled.
For addit ional informat ion, refer t o:
Ins trument Clus ter (413-01 Ins t rument Clus t er, Descripti on and Operat ion),Informat ion and Mes s age Cent er (413-08 Informati on and Mes sage Cent er, Descripti on and Operat ion).
To monit or for brake overheat, t he ABS modul e monit ors t he amount of braking acti vi ty and, from thi s, es ti mat es thet emperature of each brake. If the es t imat ed temperature of any brake exceeds a pres et li mit , t he ABS module i nvokes t hefade out s t rategy. Aft er the fade out cycle, t he HDC funct ion i s re-enabl ed when the ABS modul e es ti mates that all of thebrake t emperatures are at l ess than 64% of the preset t emperat ure l imi t.
Roll Stability Control
The RSC funct ion us es the brakes and the engine t o at tempt t o rest ore vehicle s tabilit y, i f the vehicle is forced i nt o ahars h maneuver t hat ri sks i t ti pping over.
The ABS module monit ors dri ver i nput s and vehicle behavior usi ng various powert rai n s ignals and t he i nput s from thewheel s peed s ens ors, t he s teering angle s ens or, the roll rate sens or, yaw rate and lateral accel erat ion s ensors. Thes einputs are compared wit h modeled behavi or and, if t he vehicle behavior reaches a given ris k level, t he ABS module cut st he engi ne power, or brakes one or more wheels suffi ci ent ly to al low the vehicle to regain s t abi li ty and hel p the driverremai n i n cont rol .
W hi le t he i gni ti on is energi zed, RSC i s permanentl y enabl ed even if t he DSC functi on is sel ect ed off.
Terrain Response™ System Integration
The Terrai n Res pons e™ funct ion integrat es t he ABS and other vehicle s ys tem cont rol modules t o as si s t the vehicle whendri vi ng off-road or during di fficult s urface condit ions . Terrai n Respons e is act ivated when the rotary cont rol s wit ch is s et t oa Terrain Res ponse special program.
W hen a Terrai n Respons e s peci al program i s acti vat ed, t he ABS module along wi th ot her vehicle s ys t em control modul eswil l operate in accordance wi th programmed software maps . The s oftware maps al low t he ABS s ys tem to functi on wit h at hreshol d that wi ll as si s t the s elected Terrai n Respons e s pecial program.For addit ional informat ion, refer t o: Ride and Handli ng Opti mizat ion (204-06 Ride and Handli ng Opt imi zat ion, Descripti onand Operat ion).

Publi s hed: 11-May-2011
Steering Column Switches - Steering Column Switches
Des cript ion and Operat ion
COMPONENT LOCATION
ItemPart NumberDescription
1-Speed cont rol s wit ches2-St eering column cas e containi ng the mult ifunct ion s wit ches and cl ocks pring
3-Audio control swit ches
OVERVIEW
The winds hield wiper s wit ch is l ocat ed in the right -hand-s ide of t he cas e and retai ned wit h 2 s crews . The s wit ch isconnected t o t he mai n harness vi a a connect or at the back of the s wi tch. The s wit ch cont rols the followi ng functi ons :
W i nds hiel d wi per i nt ermit tent s low and fas t speedW i nds hiel d wi per fli ck wipeW i nds hiel d was h/wi peRear was h/wipeInt ermit tent delay s electi on.
The t urn s ignal indicator s wit ch is locat ed i n t he left -hand-si de of the cas e and ret ained wi th 2 s crews . The swi tch i sconnected t o t he mai n harness vi a a connect or on the back of t he swit ch. The s wit ch cont rol s the foll owing funct ions:
Left / right turn s ignal operati onHigh / low beam operati onHeadl amp flas hTri p comput er functi on s el ect ion (i f fit t ed).
The t rip but t on allows the driver to cycle t hough an opti on menu and als o reset t ri p cycl e mi leage cal cul ati ons . The t ripcomput er informat ion i s dis played in the i nst rument clus ter mes s age cent er (high line ins trument cl us t er onl y).
Steering wheel mount ed s wit ches on the right -hand-s ide of t he dri ver's ai rbag, cont rol the audi o and tel ephone funct ions.Swit ches on the l eft -hand-s ide of t he dri ver's ai rbag control t he s peed cont rol functi ons .
The clocks pri ng is locat ed i n the front of t he cas e and retai ned wit h four s crews . The clocks pri ng engages i n s lots in t hes teeri ng wheel bos s and t urns wi th the rotat ion of t he s teeri ng wheel. The clocks pring incorporat es a t ang which cancelst he turn s ignal indicators when the st eering wheel i s rot ated.For addit ional informat ion, refer t o: Air Bag and Safet y Belt Pretens ioner Supplement al Res traint Syst em (SRS) (501-20BSuppl ement al Rest rai nt Sys tem, Des cri pti on and Operati on).
CONTROL DIAGRAM
• NOTE: A = Hardwi red; D = Hi gh s peed CAN bus , O = LIN bus

1-Pres s t o s wit ch between radi o, CD, or AUX
2-Pres s t o i ncreas e volume
3-Pres s t o decrease vol ume4-Pres s and release to scrol l through preset radi o s t at ions or CD tracks . Pres s to search up or down fort he next or previous radio s t at ion/CD t rack
The audi o control s wi tches are res is ti ve ladder swi tches. Thes e s wit ches connect t o t he Infotainment Control Modul e (ICM)or Int egrated Audi o Modul e (IAM) (dependant upon the l evel of audi o fit ted t o t he vehicle) via t he clockspring.
For addit ional informat ion, refer t o: Audi o Sys tem (415-01, Des cript ion and Operat ion).
Speed Control Switches
ItemPart NumberDescription
1-Set t arget speed, or increase s peed
2-Set t arget speed, or decreas e s peed3-Res ume s et s peed
4-Cancel s s peed cont rol operati on wit hout erasi ng memorized s peed
The s peed control swit ches are res is t ive l adder type. The s ignals from the res is ti ve ladder are fed t o the st eeri ng col umnmodule (located in t he clocks pri ng) which t hen out put s t he s ignals as a local i nterconnect net work (LIN) bus s ignal to thecent ral junct ion box (CJB). The CJB trans mi ts speed cont rol s ignals on the hi gh s peed controll er area network (CAN) bus t ot he engi ne cont rol module (ECM).
For addit ional informat ion, refer t o: Speed Cont rol (310-03A Speed Cont rol - I6 3.2L Petrol, Des cript ion and Operat ion).
For addit ional informat ion, refer t o: Speed Cont rol - 2.2L Di esel (310-03, Des cri ption and Operati on).

ItemPart NumberDescription
1-Transmis s ion eye end2-Abut ment
3-Damper wei ght
4-Bul khead grommet5-Sel ect or lever arm eye end and set ti ng butt on
The t ransmis s ion cable as s embly i s a one-pi ece, push/pul l cable connect ed between the t rans mis s ion and the s electorlever.
The s elect or lever end of the cable has an adjus t abl e eye end which l ocat es on a ball pi n on t he s el ect or lever. Anabut ment on t he cabl e outer s heat h l ocat es in an aperture at the front of t he s el ector lever shi ft housi ng.
A fireproof grommet s eal is pos it ioned approxi mat el y half way al ong the l engt h of t he cable and s eal s the cable through ahole i n t he bulkhead.
The t ransmis s ion end of t he cabl e als o has an eye end whi ch locat es on a bal l pi n on t he end of the trans mi ss i on leverarm. An abut ment on t he out er s heat h locates i n a bracket att ached to t he t op of the trans mi ss i on.
Linear movement of t he s el ect or lever is t rans ferred, via t he inner cabl e, into movement of t he t ransmis s ion l ever arm. Thelever arm convert s t he li near movement of the s elect or cable i nto rot ary movement of the manual s haft in thet ransmis s ion.
Cable Setting Proced ure
The correct cabl e adjus tment i s achi eved by use of a yel low but ton in t he s elector lever arm eye end. The s et ti ng proces sis to ens ure that t he trans mi s si on is in Park (P) and t he s elector lever is i n i ts det ent e park pos i ti on. This can be checkedby s electi ng the Park (P) pos it ion and wi th the park brake released, rocking t he vehicle forward and back to ens ure that thet ransmis s ion parki ng pawl i s engaged.
Once the cable is i n t he correct posi ti on, t he yell ow s ett ing but ton can be engaged wit h t he s errat ed port ion of t he cabl e.Acces s t o t he set ti ng butt on is through t he apert ure i n t he upper face of t he s hift hous ing.
The cabl e s houl d be reset whenever any part of t he t ransmis s ion s hift s ys t em has been dis t urbed or replaced, i ncl udi ngt he trans mi s si on, operat ing arms , abut ment bracket s cabl es or s el ect or lever as s embly.

5. CAUTION: Di scard the bolt s .
• NOTE: Loosen the bolt s of t he cl utch pres s ure pl ateeach two turns at a t ime in t he s equence s hown.
• NOTE: Res train t he flywheel .
5.
Installation
1. NOTE: The cl utch cover i s s elf adjus ti ng. It i srecommended t hat a cl utch di sc and cl ut ch cover isrepl aced as an as s embly. If a us ed cl utch cover i sas sembl ed wit h a new clutch di sc, t he clutch coveradjus tment must be res et prior t o as sembl y. W it h t heclut ch cover support ed under i ts out s ide edge, pressdown evenl y on t he diaphragm fi ngers as s hown, unt ilt he clutch cover adjus t ment ri ng can be rot ated full ycount erclockwis e. W it h t he adjus tment ring hel d in thi spos it ion, releas e t he pres s ure on t he diaphragmfingers . The adjus tment ring wi ll be held in t hispos it ion unti l sel f adjust ment on t he appl icati on of theclut ch pedal.
Check, and i f necess ary, reset t he clut ch press ureplat e.
1.

Once the cable is i n t he correct posi ti on, t he yell ow adjus tment but ton can be pressed back int o t he 'locked' pos it ion t oengage wit h the serrat ed port ion of t he cable. Ens ure t hat the s elect or l ever i s not moved before t he butt on i s pres s ed.
Check t he cable for the correct s et ti ng by s el ect ing 3rd gear and checki ng t hat t he l at eral movement of the s elector l everfeel s s ymmetrical.
The cabl e s houl d be reset whenever any part of t he t ransmis s ion s elector as sembl y has been dis turbed or replaced,including the t rans mis s ion, cabl es or sel ect or lever as s embly.