Page 969 of 3229
Publi s hed: 11-May-2011
Engine Cooling - TD4 2.2L Diesel - Cooling Fan
Removal and Inst all ati on
Removal
1.
2.
3.
Page 970 of 3229
Tie the Ai r Condi ti oni ng (A/C) pipes as ide.4.
5. CAUTION: Not e the routi ng of the lines andhos es .5.
Installation
To i nst all , revers e t he removal procedure.1.
Page 971 of 3229
Publi s hed: 11-May-2011
Engine Cooling - TD4 2.2L Diesel - Cooling Fan Module
Removal and Inst all ati on
Removal
• NOTE: Petrol ill ust rat ion s hown, dies el s i mil ar.
Remove t he cover and dis connect the bat tery ground cabl e.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
1.
Remove t he cool ing fan module. T orque:
6 Nm 2.
Installation To i nst all , revers e t he removal procedure.
1.
Page 972 of 3229
Publi s hed: 11-May-2011
Engine Cooling - TD4 2.2L Diesel - Coolant Expansion Tank
Removal and Inst all ati on
Removal W ARNING: W hen rel eas i ng the cooli ng s ys t em pres s ure, cover t he cool ant expansi on tan
k cap wi th a t hi ck cl oth.T orque:
10 Nm 1.
Clamp the relevant hos e, t o mi ni mis e coolant los s .
2. 3. CAUTION: Be prepared to col lect escaping
cool ant.
3.
Page 973 of 3229
4.
NOTE: Do not di s as s emble furt her if t he component
is removed for acces s only.
4.
Installation To i nst all , revers e t he removal procedure.
1.
Top-up t he cool ant.
2.
Page 974 of 3229
Publi s hed: 11-May-2011
Engine Cooling - TD4 2.2L Diesel - Engine Coolant Level Switch
Removal and Inst all ati on
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s. T orque:
10 Nm 1.
2.
Installation To i nst all , revers e t he removal procedure.
1.
Page 975 of 3229
Publi s hed: 11-May-2011
Fuel Charging and Controls - I6 3.2L Petrol -
General SpecificationItemSpecification
Recommended fuel:
UK, Europe91 - 98 RONUSAMinimum 91 CLC or AKI
Fuel injectors:
MakeDens o
Fuel Pressures
ComponentbarpsiFuel rail - normal operat ing condit ions - not usi ng IDS3.754
Fuel rail - normal operat ing condit ions - us ing IDS4.868
Fuel rail - engine off - usi ng IDS2.8 to 3.240 t o 46Fuel rail - cold s t art - us ing IDS6.594
Torque Specifications
DescriptionNmlb-ft
Fuel i njector clamp pl ate bol ts65Fuel press ure regulat or bol ts65
Fuel pump drive modul e ret aining bol ts107
Fuel rail bolt s107Fuel rail pres s ure s ens or65
Schreader valve bolt s65
Throt tl e body s crews86
Page 976 of 3229
Publi s hed: 11-May-2011
Fuel Charging and Controls - I6 3.2L Petrol - Fuel Charging and Controls
Des cript ion and Operat ion
Authori ng Templat e
COMPONENT LOCATION
ItemPart NumberDescription1-Fuel rai l
2-Fuel inject or
3-Fuel li ne4-Fuel rai l press ure and fuel temperature s ens or
OVERVIEW
The fuel pump module, l ocat ed in the fuel t ank, i s electronical ly regulated by the Engine Management Sys t em (EMS) toprovide controll ed pres sure in the fuel railFor addit ional informat ion, refer t o: Fuel Tank and Lines (310-01A Fuel Tank and Lines - I6 3.2L Pet rol, Des cri pt ion andOperat ion)..
Suppl yi ng t he correct amount of fuel as required by the engine at any gi ven moment, eli minat es the requirement foraddi ti onal pi pes returning exces s fuel t o t he fuel t ank. The benefit s of t hi s t ype of s ys tem are:
Reduced l oad on the el ect ri cal s yst em