Page 97 of 3229

Publi shed: 20-Jul-2011
General Information - Diagnostic Trouble Code (DTC) IndexI6 3.2L Petrol,
DTC: Engine Control Module (ECM)
Des cript ion and Operat ion
• NOTE: If a cont rol module or component i s s uspect and the vehicl e remai ns under manufacturer warrant y, refer t o t heW arranty Pol icy and Procedures manual (s ect ion B1.2), or determine i f any pri or approval program is i n operat ion, beforet he replacement of a component.
• NOTE: Generic scan t ool s may not read the codes li st ed, or may read only 5-digi t codes . Match t he 5 digi ts from t he s cant ool t o t he fi rs t 5 di gi ts of the 7-digit code li s ted t o i dent ify the fault (the last 2 digi ts gi ve ext ra informati on read by themanufacturer-approved di agnos ti c s ys t em).
• NOTE: W hen performing volt age or res is t ance t est s , always use a digi tal mult imeter (DMM) accurat e t o t hree deci malplaces, and wi th an up-t o-date cal ibrat ion cert ificate. W hen tes ti ng res is t ance al ways take t he res is t ance of t he DMMleads i nt o account .
• NOTE: Check and recti fy bas ic faul ts before beginni ng diagnos t ic rout ines i nvol vi ng pinpoint t es t s.
• NOTE: Ins pect connect ors for s igns of water ingres s , and pins for damage and/or corros ion.
• NOTE: If di agnos t ic t rouble codes are recorded and, after performi ng t he pinpoi nt tes t s, a fault i s not pres ent , anint ermi tt ent concern may be the caus e. Al ways check for l oos e connect ions and corroded t erminals .
Des cript ion And Operat ion
For a detail ed descripti on of the El ect ronic engi ne cont rol s ys t em, refer t o t he relevant Des cript ion and Operat ion secti onin the workshop manual.For addit ional informat ion, refer t o: Electroni c Engi ne Control s (303-14A Electroni c Engi ne Controls- I6 3.2L Pet rol, Des cri pt ion and Operati on).
Powertrain control module petrol (PC MP) SI6 petrol engineDT CDescriptionPossible CauseAction
B1024-00Start cont rol unit - Nos ub type i nformati onStart er rel ay si gnal circui t:short ci rcuit t o groundStart er rel ay si gnal circui t:short ci rcuit t o powerStart er rel ay si gnal circui t:open ci rcuitStart er rel ay fault
Check t he st art er rel ay and ci rcuit s. Refer tot he elect rical guides. Ins tall a new rel ay asnecess ary
B1024-82Start cont rol unit -Ali ve/s equencecount er incorrect/notupdat ed
Cont rol ler area net work(CAN) circui t: open circui tCAN circui t: s hort circui t togroundCAN circui t: s hort circui t topower
Check t he CAN circui t. Refer t o t he electricalgui des . Rect ify as neces s ary
B1024-86Start cont rol unit -Signal inval idCont rol ler area net work(CAN) circui t: open circui tCAN circui t: s hort circui t togroundCAN circui t: s hort circui t topower
Check t he CAN circui t. Refer t o t he electricalgui des . Rect ify as neces s ary
B10A2-68Cras h i nput - Eventinformat ionEvent informat ionThe cont rol module hasregis t ered t hat t he vehiclehas been i n a coll is ion
Cl ear t he DTC. Check/recti fy any damageres ul ti ng from the coll is ion
P0011-00Int ake (A) cams haftposi ti on t imi ng -Over-advanced (bank1) - No s ub t ypeinformat ion
Poor engine oi lqual it y/condi ti onVariable val ve ti mi ng (VVT)sol enoi d/circui t faultVVT unit faul t
Check for related DTC's. Check t he engi ne oilquali ty/condit ion. Check t he VVT s olenoid andci rcuit s. Refer t o t he electrical gui des . Inst alla new VVT unit as requi red
P0012-00Int ake (A) cams haftposi ti on t imi ng -Over-ret arded (bank 1)- No s ub t ypeinformat ion
Poor engine oi lqual it y/condi ti onLow engi ne oil pres s ureVariable val ve ti mi ng (VVT)sol enoi d/circui t faultVVT unit faul t
Check for related DTC's. Check t he engi ne oilquali ty/condit ion. Check t he engine oi lpress ure. Check the VVT sol enoi d andci rcuit s. Refer t o t he electrical gui des . Inst alla new VVT unit as requi red
P0012-68Int ake (A) cams haftposi ti on t imi ng -Over-ret arded (bank 1)- Event i nformati on
Poor engine oi lqual it y/condi ti onLow engi ne oil pres s ureVariable val ve ti mi ng (VVT)uni t fault- camshaft res et val ve
Check t he engi ne oil qual it y/condi ti on. Checkt he engine oi l press ure. Check the VVT uni t.Ins tall a new VVT unit as requi red
P0016-00Cranks haft pos i ti on -Cams haft posi ti oncorrel ati on - Bank 1s ens or A - No s ub typeinformat ion
Poor engine oi l quali tyCamshaft inlet s ensorincorrect ly i ns t alledCrankshaft pos it ion sens orincorrect ly i ns t alled
Check t he engi ne oil qual it y/condi ti onRefer to t he relevant s ecti ons of t heworkshop manual and check t he camshafti nlet s ens or for correct i nst all ati on, check t hecranks haft posi ti on s ens or for correct
Page 98 of 3229

DT CDescriptionPossible CauseAction
Camshaft inlet s ensor, s hortci rcuit t o ground, s hortci rcuit t o power, open circui t,high res i st anceCamshaft inlet s ensorair-gap t o t arget rot orgreater t han specificati onExces si ve run out on t argetrot orLoos e vari abl e valve t imi ngact uat or chai n dri ve ortens ionersDamaged, worn ti mi ng chain
i nst all ati onRefer to el ect ri cal circui t diagrams and checkt he cams haft inl et sens or ci rcuit for s hortci rcuit t o ground, short ci rcuit t o power, openci rcuit , hi gh res is t anceRefer to t he relevant s ecti ons of t heworkshop manual and check t he camshafti nlet s ens or for correct ai r-gap to target rotors pacing, check target run out is tos pecifi cat ion, check vari abl e valve t imingact uat or chain drive or t ensi oners areoperat ing t o s peci fi cat ion
P0018-00Cranks haft pos i ti on -Cams haft posi ti oncorrel ati on - Bank 2s ens or A - No s ub typeinformat ion
Poor engine oi lqual it y/condi ti onIncorrect ly adjus t edcams haft sDamaged (worn) ti mingchainVariable val ve ti mi ng (VVT)sol enoi d/circui t faultVVT unit faul t
Check t he engi ne oil qual it y/condi ti on. Checkt he cams haft t imi ng and chai n. Recti fy asnecess ary. Check the VVT sol enoi d andci rcuit s. Refer t o t he electrical gui des Ins tal la new VVT unit as requi red
P001A-00Int ake (A) cam profi lecont rol circui t/open(bank 1) - No sub typeinformat ion
Camshaft profi le controlci rcuit : open ci rcuitCamshaft profi le controlci rcuit : s hort circuit t ogroundCamshaft profi le act uat orfault
Check t he cams haft profi le actuat or andci rcuit s. Refer t o t he electrical gui des . Recti fyas necess ary
P001B-00Int ake (A) cam profi lecont rol circui t low(bank 1) - No sub typeinformat ion
Camshaft profi le controlci rcuit : open ci rcuitCamshaft profi le controlci rcuit : s hort circuit t ogroundCamshaft profi le act uat orfault
Check t he cams haft profi le actuat or andci rcuit s. Refer t o t he electrical gui des . Recti fyas necess ary
P001C-00Int ake (A) cams haftprofile cont rol circuithigh (bank 1) - No s ubt ype i nformati on
Camshaft profi le controlci rcuit : s hort circuit t o powerCamshaft profi le act uat orfault
Check t he cams haft profi le actuat or andci rcuit s. Refer t o t he electrical gui des . Recti fyas necess ary
P001D-00Int ake (A) cam profi lecont rol circui t/open(bank 2) - No sub typeinformat ion
Camshaft profi le controlci rcuit : open ci rcuitCamshaft profi le controlci rcuit : s hort circuit t ogroundCamshaft profi le act uat orfault
Check t he cams haft profi le actuat or andci rcuit s. Refer t o t he electrical gui des . Recti fyas necess ary
P001E-00Int ake (A) cams haftprofile cont rol circuitlow (bank 2) - No s ubt ype i nformati on
Camshaft profi le controlci rcuit : open ci rcuitCamshaft profi le controlci rcuit : s hort circuit t ogroundCamshaft profi le act uat orfault
Check t he cams haft profi le actuat or andci rcuit s. Refer t o t he electrical gui des . Recti fyas necess ary
P001F-00Int ake (A) cams haftprofile cont rol circuithigh (bank 2) - No s ubt ype i nformati on
Camshaft profi le controlci rcuit : s hort circuit t o powerCamshaft profi le act uat orfault
Check t he cams haft profi le actuat or andci rcuit s. Refer t o t he electrical gui des . Recti fyas necess ary
P0021-00Int ake (A) cams haftposi ti on t imi ng overadvanced (bank 2) -No s ub t ypeinformat ion
Poor engine oi lqual it y/condi ti onVariable val ve ti mi ng (VVT)sol enoi d/circui t faultVVT unit faul t
Check for related DTC's. Check t he engi ne oilquali ty/condit ion. Check t he VVT s olenoid andci rcuit s. Refer t o t he electrical gui des . Inst alla new VVT unit as requi red
P0022-00Int ake (A) cams haftposi ti on t imi ng overret arded (bank 2) - Nos ub type i nformati on
Poor engine oi lqual it y/condi ti onLow engi ne oil pres s ureVariable val ve ti mi ng (VVT)sol enoi d/circui t faultVVT unit faul t
Check for related DTC's. Check t he engi ne oilquali ty/condit ion. Check t he engine oi lpress ure. Check the VVT sol enoi d andci rcuit s. Refer t o t he electrical gui des . Inst alla new VVT unit as requi red
P0031-00HO2S Heater controlcircuit low (bank 1,s ens or 1) - No s ubt ype i nformati on
HO2S heat er cont rol circui t:short ci rcuit t o groundHO2S heat er cont rol circui t:open ci rcuitHO2S faul t
Check t he HO2S and circuit s . Refer to theel ect ri cal guides . Ins tal l a new s ensor asrequi red
Page 99 of 3229

Publ is hed: 28-Apr-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Front
Controls Display Interface Module (FCDIM) - Front Integrated Control Panel
Des cript ion and Operat ion
• NOTE: If a cont rol module or component i s s uspect and the vehicl e remai ns under manufacturer warrant y, refer t o t heW arranty Pol icy and Procedures manual (s ect ion B1.2), or determine i f any pri or approval program is i n operat ion, beforet he replacement of a component.
• NOTE: Generic scan t ool s may not read the codes li st ed, or may read only 5-digi t codes . Match t he 5 digi ts from t he s cant ool t o t he fi rs t 5 di gi ts of the 7-digit code li s ted t o i dent ify the fault (the last 2 digi ts gi ve ext ra informati on read by themanufacturer-approved di agnos ti c s ys t em).
• NOTE: W hen performing volt age or res is t ance t est s , always use a digi tal mult imeter (DMM) accurat e t o t hree deci malplaces, and wi th an up-t o-date cal ibrat ion cert ificate. W hen tes ti ng res is t ance al ways take t he res is t ance of t he DMMleads i nt o account .
• NOTE: Check and recti fy bas ic faul ts before beginni ng diagnos t ic rout ines i nvol vi ng pinpoint t es t s.
• NOTE: Ins pect connect ors for s igns of water ingres s , and pins for damage and/or corros ion.
• NOTE: If DTCs are recorded and, aft er performi ng the pi npoi nt tes ts , a fault is not present , an int ermi tt ent concern maybe t he caus e. Always check for loose connect ions and corroded terminals .
Des cript ion And Operat ion
For a detail ed descripti on of the front di spl ay interface s yst em, refer to the relevant Des cri pt ion and Operati on s ect ion i nt he works hop manual .For addit ional informat ion, refer t o: Audi o Sys tem (415-01 Informati on and Entertainment Sys tem, Des cript ion andOperat ion).
Front C ontrol Display Interface Module (FC DIM) (high level display front)
DT CDescriptionPossible CauseAction
U1A01-15Communicati onsli nkNavigati on module t o Hi gh LevelDis play Front communi cat ions li nkcircuit - short to power, opencircuit
Refer t o electrical ci rcuit diagrams and check Navigati onModule t o Hi gh Level Dis play Front communicat ions li nkcircuit for s hort to power, open ci rcuit
U1A4B-48Control modul emi croproces s or 'B'Supervis ion s oft ware fail ureIns t all a new HLDF.For addit ional informat ion, refer t o: Video Di spl ay (415-01Informat ion and Ent ert ai nment Sys t em, Removal andIns t allat ion).
U3000-48Control modul eSupervis ion s oft ware fail ureIns t all a new HLDF.For addit ional informat ion, refer t o: Video Di spl ay (415-01Informat ion and Ent ert ai nment Sys t em, Removal andIns t allat ion).
U3000-4BControl modul eOver temperat ureCheck for addi ti onal DTCs and refer to DTC Index.Check/moni tor s ys tem for re-occurrenceU3000-55Control modul eIncorrect Car Confi gurati on Filedata recei vedCheck/up-dat e Car Confi gurati on File usi ng manufacturerapproved diagnos t ic s yst emU3000-87Control modul eMis s ing mess ageCheck CJB for DTCs and refer t o DTC Index.For addit ional informat ion, refer t o: Communicati onsNetwork (418-00 Modul e Communi cat ions Network,Diagnosi s and Tes ti ng).Check i nformati on and ent ert ainment module for CarConfigurat ion Fi le and MOST network DTCs and refer t orel evant DTC Index. Carry out MOST/CAN net work tes tsus ing t he manufacturer approved diagnost ic sys tem
U3000-98Control modul eComponent or s yst em overt emperatureCheck for addi ti onal DTCs and refer to DTC Index.Check/moni tor s ys tem for re-occurrence
U3003-16Batt ery vol tageCircui t vol tage below thresholdCarry out pinpoi nt tes t s ass ociated wit h t hi s DTC us ingt he manufact urer approved diagnost ic s ys tem
U3003-17Batt ery vol tageCircui t vol tage above t hreshol dCarry out pinpoi nt tes t s ass ociated wit h t hi s DTC us ingt he manufact urer approved diagnost ic s ys tem
Page 100 of 3229

Publi s hed: 04-May-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Headlamp
Control Module (HCM)
Des cript ion and Operat ion
• NOTE: If a cont rol module or component i s s uspect and the vehicl e remai ns under manufacturer warrant y, refer t o t heW arranty Pol icy and Procedures manual (s ect ion B1.2), or determine i f any pri or approval program is i n operat ion, beforet he replacement of a component.
• NOTE: Generic scan t ool s may not read the codes li st ed, or may read only 5-digi t codes . Match t he 5 digi ts from t he s cant ool t o t he fi rs t 5 di gi ts of the 7-digit code li s ted t o i dent ify the fault (the last 2 digi ts gi ve ext ra informati on read by themanufacturer-approved di agnos ti c s ys t em).
• NOTE: W hen performing volt age or res is t ance t est s , always use a digi tal mult imeter (DMM) accurat e t o t hree deci malplaces, and wi th an up-t o-date cal ibrat ion cert ificate. W hen tes ti ng res is t ance al ways take t he res is t ance of t he DMMleads i nt o account .
• NOTE: Check and recti fy bas ic faul ts before beginni ng diagnos t ic rout ines i nvol vi ng pinpoint t es t s.
• NOTE: Ins pect connect ors for s igns of water ingres s , and pins for damage and/or corros ion.
• NOTE: If DTCs are recorded and, aft er performi ng the pi npoi nt tes ts , a fault is not present , an int ermi tt ent concern maybe t he caus e. Always check for loose connect ions and corroded terminals .
For addit ional informat ion, refer t o: Ext eri or Li ght ing (417-01 Ext erior Light ing, Descri pti on and Operat ion).
Adaptive Front Lighting System (AFS) C ontrol Module
DT CDescriptionPossible CauseActionB1041-04Level ing Control -Syst em InternalFailures
Module internal failureSus pect Adapt ive Front Light ing Syst em (AFS) Cont rolModul e i nt ernal fault . Replace as required, refer t o t he newmodule/component i nst all at ion not e at t he top of t he DTCIndexB1041-54Level ing Control -Mis s ing Cal ibrat ion• NO TE: This DTC wil l normall ybe l ogged when a new modulehas been ins t al led.
Level ing s ens orcali brati on rout ine notcarried out
• NOTE: Sens or cal ibrat ion routi ne mus t be carried out wit hthe vehicle unl aden.
Calibrate t he Headlamp Leveli ng sens ors us ing themanufacturer approved diagnost ic sys tem, carry t he outrout ine 'Headlamp Cont rol Module Sys tem Cali brati on' fromthe 'Modul e programming and confi gurati on - Setup andConfigurat ion - Li ght ing'B1087-83LIN Bus "A" - Val ueof s ignal protecti oncal cul ati on incorrect
LIN Bus circui t faultNo communi cat ion ont he LIN BusLIN bus EMCi nt erference
• NOTE: This circui t uses s hiel ded cable
Refer to the el ect ri cal circui t diagrams and check the LINBus ci rcuit for harness damage
B1087-86LIN Bus "A" - Si gnalInvali dLIN Bus circui t faultNo communi cat ion ont he LIN BusLIN bus EMCi nt erference
• NOTE: This circui t uses s hiel ded cable
Refer to the el ect ri cal circui t diagrams and check the LINBus ci rcuit for harness damage
B1087-88LIN Bus "A" - BusOffLIN Bus circui t faultNo communi cat ion ont he LIN Bus
• NOTE: This circui t uses s hiel ded cable
Refer to the el ect ri cal circui t diagrams and check the LINBus ci rcuit for harness damageB10AE-11Headl amp Level ingMotor - Ci rcuit s hortt o ground
Headlamp Leveli ngMot or control ci rcuits hort t o ground
Refer to the el ect ri cal circui t diagrams and check Headl ampLeveli ng Motor control ci rcuit for s hort t o ground
B10AE-12Headl amp Level ingMotor - Ci rcuit s hortt o batt ery
Headlamp Leveli ngMot or control ci rcuits hort t o power
Refer to the el ect ri cal circui t diagrams and check Headl ampLeveli ng Motor control ci rcuit for s hort t o power
B10AE-64Headl amp Level ingMotor - Si gnalplaus ibil it y fai lure
Signal plaus ibil it y fai lure(vol tage out of range)Refer to the el ect ri cal circui t diagrams and check Headl ampLeveli ng Motor circui ts for fai lure. Di sconnect one headlampconnect or, clear DTC and re-t est . If DTC cleared, s us pectAdapt ive Front Light ing Sys tem (AFS) Control Module orci rcuit s t o t he dis connect ed s ide of t he fai lure. If DTCremai ns , reconnect first headlamp and dis connect s econd,cl ear DTC and re-tes t. If DTC cleared, s us pect Adapt iveFront Lighti ng Sys t em (AFS) Cont rol Modul e or circui ts t othe di s connect ed s ide of t he fai lure. If DTC remai ns,s us pect common ci rcuit s of the fail ure. Refer t o t heelectrical ci rcuit diagrams and check as requi red
B1A59-11Sens or 5 Vol t Supply- Circui t s hort toground
Headlamp Leveli ngSensor 5 vol t supplycircui t s hort to ground
Refer to electrical ci rcuit diagrams and check HeadlampLeveli ng Sens or 5 volt s upply circui t for s hort t o ground
B1A59-12Sens or 5 Vol t Supply- General ElectricalFailure
Headlamp Leveli ngSensor 5 vol t supplycircui t s hort to power
Refer to electrical ci rcuit diagrams and check HeadlampLeveli ng Sens or 5 volt s upply circui t for s hort t o power
Page 101 of 3229

DT CDescriptionPossible CauseAction
B1D64-01Left HeadlampSwivell ing Mot or -General Elect ricalFailure
Internal Headlamp Mot orFaultInternal HeadlampCi rcuit Faul t
Us ing t he manufacturer approved diagnost ic sys temperform an On Demand Self Tes t, l ook for any errors i nmovement (compare wi th other headl amp) and vi sual lyins pect t he lamp for i nt ernal damage or di s locat ion (balljoi nt s out). Refer t o t he electrical ci rcuit diagrams andcheck for circui t faul t bet ween t he Adapt ive Front Light ingSys t em (AFS) Cont rol Modul e and t he Headl amp Swi vel lingMotor. If no mechanical or circui t fault s are evident ,s us pect headlamp int ernal fault , replace as requi red. Referto the new modul e/component i nst all at ion not e at t he topof the DTC Index
B1D64-87Left HeadlampSwivell ing Mot or -Mis s ing mess age
Mi ss i ng mes sageUs ing t he manufacturer approved diagnost ic sys temperform an On Demand Self Tes t, l ook for any errors i nmovement (compare wi th other headl amp) and vi sual lyins pect t he lamp for i nt ernal damage or di s locat ion (balljoi nt s out). Refer t o t he electrical ci rcuit diagrams andcheck for circui t faul t bet ween t he Adapt ive Front Light ingSys t em (AFS) Cont rol Modul e and t he Headl amp Swi vel lingMotor. If no mechanical or circui t fault s are evident ,s us pect headlamp int ernal fault , replace as requi red. Referto the new modul e/component i nst all at ion not e at t he topof the DTC IndexB1D65-01Right HeadlampSwivell ing Mot or -General elect ricalfai lure
Internal Headlamp Mot orFaultInternal HeadlampCi rcuit Faul t
Us ing t he manufacturer approved diagnost ic sys temperform an On Demand Self Tes t, l ook for any errors i nmovement (compare wi th other headl amp) and vi sual lyins pect t he lamp for i nt ernal damage or di s locat ion (balljoi nt s out). Refer t o t he electrical ci rcuit diagrams andcheck for circui t faul t bet ween t he Adapt ive Front Light ingSys t em (AFS) Cont rol Modul e and t he Headl amp Swi vel lingMotor. If no mechanical or circui t fault s are evident ,s us pect headlamp int ernal fault , replace as requi red. Referto the new modul e/component i nst all at ion not e at t he topof the DTC Index
B1D65-87Right HeadlampSwivell ing Mot or -Mis s ing mess age
Mi ss i ng mes sageUs ing t he manufacturer approved diagnost ic sys temperform an On Demand Self Tes t, l ook for any errors i nmovement (compare wi th other headl amp) and vi sual lyins pect t he lamp for i nt ernal damage or di s locat ion (balljoi nt s out). Refer t o t he electrical ci rcuit diagrams andcheck for circui t faul t bet ween t he Adapt ive Front Light ingSys t em (AFS) Cont rol Modul e and t he Headl amp Swi vel lingMotor. If no mechanical or circui t fault s are evident ,s us pect headlamp int ernal fault , replace as requi red. Referto the new modul e/component i nst all at ion not e at t he topof the DTC Index
B1D68-00Left HeadlampSwivell ing FeedbackSens or - No s ub t ypeinformat ion
Internal HeadlampSensor FaultInternal HeadlampCi rcuit Faul t
Us ing t he manufacturer approved diagnost ic sys temperform an On Demand Self Tes t, l ook for any errors i nmovement (compare wi th other headl amp) and vi sual lyins pect t he lamp for i nt ernal damage or di s locat ion (balljoi nt s out). Refer t o t he electrical ci rcuit diagrams andcheck for circui t faul t bet ween t he Adapt ive Front Light ingSys t em (AFS) Cont rol Modul e and t he Headl amp Swi vel lingFeedback Sens or. If no mechani cal or circuit fault s areevi dent , s us pect headlamp int ernal fault , replace asrequired. Refer t o t he new modul e/component ins t al lat ionnot e at t he t op of the DTC IndexB1D69-00Right HeadlampSwivell ing FeedbackSens or - No s ub t ypeinformat ion
Internal HeadlampSensor FaultInternal HeadlampCi rcuit Faul t
Us ing t he manufacturer approved diagnost ic sys temperform an On Demand Self Tes t, l ook for any errors i nmovement (compare wi th other headl amp) and vi sual lyins pect t he lamp for i nt ernal damage or di s locat ion (balljoi nt s out). Refer t o t he electrical ci rcuit diagrams andcheck for circui t faul t bet ween t he Adapt ive Front Light ingSys t em (AFS) Cont rol Modul e and t he Headl amp Swi vel lingFeedback Sens or. If no mechani cal or circuit fault s areevi dent , s us pect headlamp int ernal fault , replace asrequired. Refer t o t he new modul e/component ins t al lat ionnot e at t he t op of the DTC Index
C1A03-12Left Front HeightSens or - Circui ts hort t o batt ery
Left Front Hei ght Sens orcircui t s hort to powerRefer to the el ect ri cal circui t diagrams , and check LeftFront Height Sens or circuit for s hort to power
C1A03-14Left Front HeightSens or - Circui ts hort t o ground oropen
Left Front Hei ght Sens orcircui t s hort to ground oropen circui t
Refer to the el ect ri cal circui t diagrams , and check LeftFront Height Sens or circuit for s hort to ground or openci rcuit
C1A05-12Left Rear HeightSens or - Circui ts hort t o batt ery
Left Rear Height Sens orcircui t s hort to powerRefer to the el ect ri cal circui t diagrams , and check Left RearHeight Sens or circuit for s hort to power
C1A05-14Left Rear HeightSens or - Circui ts hort t o ground oropen
Left Rear Height Sens orcircui t s hort to ground oropen circui t
Refer to the el ect ri cal circui t diagrams , and check Left RearHeight Sens or circuit for s hort to ground or open ci rcuit
U0001-88High Speed CANCommunicati on Bus- Bus off
CAN Bus OffCAN Bus Ci rcuit faultCheck ot her modul es for rel ated DTCs . Carry out the CANNetwork Int egrit y t est us i ng the manufact urer approveddiagnos t ic s ys tem
Page 102 of 3229

DT CDescriptionPossible CauseAction
U0101-00Lost communicat ionwit h TCM - No s ubt ype i nformati on
Los t communi cat ion wi tht he Trans mis s ionControl Modul eCAN net work fault
Check t he Trans mis s ion Cont rol Module for st ored DTCs .Us ing t he manufacturer approved diagnost ic sys tem,compl ete the CAN Net work Int egrit y t est . Refer t o theelectrical ci rcuit diagrams and check t he CAN networkbet ween t he Adapt ive Front Li ght ing Sys tem (AFS) ControlModul e and t he Trans mis s ion Cont rol Modul eU0121-00Lost communicat ionwit h Ant i-lock BrakeSyst em (ABS)Control Module - Nos ub type i nformati on
Los t communi cat ion wi tht he Anti -l ock BrakeSys tem Modul eCAN net work fault
Check t he Anti -l ock Brake Sys t em Module for s tored DTCs.Us ing t he manufacturer approved diagnost ic sys tem,compl ete the CAN Net work Int egrit y t est . Refer t o theelectrical ci rcuit diagrams and check t he CAN networkbet ween t he Adapt ive Front Li ght ing Sys tem (AFS) ControlModul e and t he Anti -l ock Brake Sys t em ModuleU0126-00Lost communicat ionwit h St eering Angl eSens or Module - Nos ub type i nformati on
Los t communi cat ion wi tht he Steering AngleSensor ModuleCAN net work fault
Check t he Steering Angle Sens or Modul e for s t ored DTCs .Us ing t he manufacturer approved diagnost ic sys tem,compl ete the CAN Net work Int egrit y t est . Refer t o theelectrical ci rcuit diagrams and check t he CAN networkbet ween t he Adapt ive Front Li ght ing Sys tem (AFS) ControlModul e and t he Steeri ng Angle Sens or Module
U0140-00Lost communicat ionwit h Body ControlModule - No subt ype i nformati on
Los t communi cat ion wi tht he Central Junct ion BoxCAN net work fault
Check t he Central Junct ion Box for s tored DTCs . Us ing themanufacturer approved diagnost ic sys tem, complet e t heCAN Net work Integri ty tes t. Refer t o t he electrical ci rcuitdiagrams and check the CAN network bet ween t he Adapt iveFront Lighti ng Sys t em (AFS) Cont rol Modul e and t he CentralJuncti on Box
U0300-00Int ernal Cont rolModule Soft wareIncompati bili ty - Nos ub type i nformati on
Car Configurat ion Fi le(CCF) i nformati oni ncompati ble t o t heAdapti ve Front Li ghti ngSys tem (AFS) Cont rolModule
• NOTE: The Car Configurat ion Fil e (CCF) parametersrequired are (Vehicle type)(Headl amp t ype)(Gearbox t ype)and (Dayrunning light )
Re-configure the Car Confi gurati on Fil e (CCF) as requi redusi ng t he manufact urer approved diagnost ic s ys tem. Cl earDTC and re-t es t . If t he DTC remains s us pect t he Adapt iveFront Lighti ng Sys t em (AFS) Cont rol Modul e, refer t o t henew module ins tall ati on not e at t he t op of the DTC IndexU0402-00Invali d Dat aRecei ved FromTrans mis s ion Cont rolModule - No subt ype i nformati on
Inval id Dat a Recei vedfrom the Transmis si onControl Modul eTrans mi ss i on componentfaul t
Check t he Trans mis s ion Cont rol Module for st ored DTCs .Us ing t he manufacturer approved diagnost ic sys tem,compl ete the CAN Net work Int egrit y t est . Refer t o theelectrical ci rcuit diagrams and check t he CAN networkbet ween t he Adapt ive Front Li ght ing Sys tem (AFS) ControlModul e and t he Trans mis s ion Cont rol Modul eU0415-00Invali d Dat aRecei ved FromAnti -Lock BrakeSyst em (ABS)Control Module - Nos ub type i nformati on
Inval id dat a receivedfrom Anti -l ock BrakeSys tem Modul eAnt i-lock Brake Syst emModule component fault
Check t he Anti -l ock Brake Sys t em Module for s tored DTCs.Us ing t he manufacturer approved diagnost ic sys tem,compl ete the CAN Net work Int egrit y t est . Refer t o theelectrical ci rcuit diagrams and check t he CAN networkbet ween t he Adapt ive Front Li ght ing Sys tem (AFS) ControlModul e and t he Anti -l ock Brake Sys t em Module
U0422-00Invali d data fromBody Cont rol Module- No s ub t ypeinformat ion
Inval id s i gnal from theCentral Juncti on BoxCentral Juncti on Boxfaul t
Check t he Central Junct ion Box for s tored DTCs . Us ing themanufacturer approved diagnost ic sys tem, complet e t heCAN Net work Integri ty tes t. Refer t o t he electrical ci rcuitdiagrams and check the CAN network bet ween t he Adapt iveFront Lighti ng Sys t em (AFS) Cont rol Modul e and t he CentralJuncti on Box
U0428-00Invali d Dat aRecei ved FromSteering AngleSens or Module - Nos ub type i nformati on
Inval id Dat a Recei vedfrom the St eeri ng Angl eSensor ModuleSt eering Angle Sens orModule fault
Check t he Steering Angle Sens or Modul e for s t ored DTCs .Us ing t he manufacturer approved diagnost ic sys tem,compl ete the CAN Net work Int egrit y t est . Refer t o theelectrical ci rcuit diagrams and check t he CAN networkbet ween t he Adapt ive Front Li ght ing Sys tem (AFS) ControlModul e and t he Steeri ng Angle Sens or
U2100-00Ini ti al Configurat ionNot Complet e - Nos ub type i nformati on
Car Configurat ion Fi le(CCF) i nformati on notreceived complet ely
• NOTE: The Car Configurat ion Fil e (CCF) parametersrequired are (Vehicle type)(Headl amp t ype)(Gearbox t ype)and (Dayrunning light )
Re-configure the Car Confi gurati on Fil e (CCF) as requi redusi ng t he manufact urer approved diagnost ic s ys tem. Cl earDTC and re-t es t . If t he DTC remains s us pect t he Adapt iveFront Lighti ng Sys t em (AFS) Cont rol Modul e, refer t o t henew module ins tall ati on not e at t he t op of the DTC IndexU2101-00Control ModuleConfigurat ionIncompati ble - Nos ub type i nformati on
Car Configurat ion Fi le(CCF) i nformati oni ncompati ble t oAdapti ve Front Li ghti ngSys tem (AFS) Cont rolModule
Check t he correct Adapti ve Front Li ght ing Sys t em (AFS)Cont rol Module is i ns t alled to vehicle s pecificati on. Refitori gi nal or repl ace the modul e as required. Refer to thenew module/component ins tall ati on note at t he t op of theDTC Index
U3003-16Batt ery Vol tage -Circui t vol tage belowt hreshol d
The power s upply to theModule has been below9 Vol ts for more than1000 mi ll is econds
Sus pect Bat t ery or Charging fault . Check t he batt erycondit ion and st ate of charge. Check t he vehicle chargi ngs ys t em. Refer to the relevant workshop manual s ect ion.Clear the DTC, cycl e i gni ti on s tat e to off t hen on, i f DTCret urns refer to the el ect ri cal circui t diagrams and checkpower and ground ci rcuit t o t he Adapt ive Front Light ingSys t em (AFS) Cont rol Modul e
Page 103 of 3229
DT CDescriptionPossible CauseAction
U3003-17Batt ery Vol tage -Circui t vol tageabove thres hold
The power s upply to theModule has been above16 Vol ts for more than1000 mi ll is econds
Sus pect Charging faul t. Check the bat tery condi ti on ands tat e of charge. Check the vehicle chargi ng s ys t em. Referto the relevant workshop manual s ect ion
U3003-62Batt ery Vol tage -Signal comparefai lure
Di fference in bat teryvolt age, of 2 volt s ormore, bet ween t hecentral broadcastvolt age (vi a CAN Bus )and Adapti ve FrontLight ing Sys tem (AFS)Control Modul e
Check ot her modul es for rel ated s t ored DTCs . Refer to theelectrical ci rcuit diagrams and check power and groundvol tages at t he Adapt ive Front Light ing Sys tem (AFS)Cont rol Module
Page 104 of 3229

Publi shed: 06-Jul-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Heating
Ventilation and Air Conditioning Control Module (HVAC)
Des cript ion and Operat ion
• NOTE: If a cont rol module or component i s s uspect and the vehicl e remai ns under manufacturer warrant y, refer t o t heW arranty Pol icy and Procedures manual (s ect ion B1.2), or determine i f any pri or approval program is i n operat ion, beforet he replacement of a component.
• NOTE: Generic scan t ool s may not read the codes li st ed, or may read only 5-digi t codes . Match t he 5 digi ts from t he s cant ool t o t he fi rs t 5 di gi ts of the 7-digit code li s ted t o i dent ify the fault (the last 2 digi ts gi ve ext ra informati on read by themanufacturer-approved di agnos ti c s ys t em).
• NOTE: W hen performing volt age or res is t ance t est s , always use a digi tal mult imeter (DMM) accurat e t o t hree deci malplaces, and wi th an up-t o-date cal ibrat ion cert ificate. W hen tes ti ng res is t ance al ways take t he res is t ance of t he DMMleads i nt o account .
• NOTE: Check and recti fy bas ic faul ts before beginni ng diagnos t ic rout ines i nvol vi ng pinpoint t es t s.
• NOTE: Ins pect connect ors for s igns of water ingres s , and pins for damage and/or corros ion.
• NOTE: If DTC's are recorded and, after performi ng t he pinpoint tes t s, a fault i s not pres ent , an i nt ermit tent concern maybe t he caus e. Always check for loose connect ions and corroded terminals .
For addit ional informat ion, refer t o: Cli mate Cont rol Syst em (412-00 Cl imat e Control Sys tem - General Informat ion,Diagnosi s and Tes ti ng).
Heating ventilation and air conditioning control module (HVAC )
DT CDescriptionPossible CauseAction
B102E-09Air quali ty s ens or generalfai lure informati on -Component fai lures
Int ernal s ens or faultInst all a new air qual it y s ensor
B102E-11Air quali ty s ens or generalelectrical fail ures - Ci rcuits hort to ground
Air quali ty s ens or circui t -s hort to groundIncorrect cli mat e cont rolmodule i nst all ed
Refer t o t he electrical ci rcuit diagrams and checkair quali ty sens or ci rcuit for short to ground. Inst alla new cl imat e control modul e as required, refer t onew modul e/component ins t al lat ion not e at thet op of the DTC Index
B102E-12Air quali ty s ens or generalelectrical fail ures - Ci rcuits hort to bat t ery
Air quali ty s ens or circui t -s hort to powerAir quali ty s ens or - O pencircuit
Refer t o t he electrical ci rcuit diagrams and checkair quali ty sens or ci rcuit for short to power. Ins tal la new air qualit y s ensor as requi red
B1030-09Left front s eat heatergeneral fail ure i nformat ion- Component failures
Seat heat er modul eint ernal fail ureInst all a new seat heater module, refer to the newmodule/component ins tal lati on note at the t op oft he DTC IndexB1030-4BLeft front s eat heaters ys t em i nternal fai lures -Over temperat ure
Seat heat er modul eint ernal fail ureSens or incorrect /nofeedback
Cl ear DTC and re-t es t. If DTC remai ns ins tal l a news eat heat er modul e, refer t o t he newmodule/component ins tal lati on note at the t op oft he DTC Index. Ins t all a new front s eat heat er mat
B1030-87Left front s eat heater buss ignal/mess age fai lures -Mis s ing mess age
LIN bus ci rcuit or s eatheat er module powers uppl y ci rcuit fault
Refer t o t he electrical ci rcuit diagrams and checkt he front left seat heater module LIN Bus circui t,power and ground s uppl y circuit s for short ci rcuit t oground, s hort circuit t o power, open circui t, hi ghresi st anceB1032-09Right front seat heatergeneral fail ure i nformat ion- Component failures
Seat heat er modul eint ernal fail ureInst all a new seat heater module, refer to the newmodule/component ins tal lati on note at the t op oft he DTC Index
B1032-4BRight front seat heaters ys t em i nternal fai lures -Over temperat ure
Seat heat er modul eint ernal fail ureSens or incorrect /nofeedback
Cl ear DTC and re-t es t. If DTC remai ns ins tal l a news eat heat er modul e, refer t o t he newmodule/component ins tal lati on note at the t op oft he DTC Index. Ins t all a new front s eat heat er mat
B1032-87Right front seat heater buss ignal/mess age fai lures -Mis s ing mess age
LIN Bus ci rcuit or s eatheat er module powers uppl y ci rcuit fault
Refer t o t he electrical ci rcuit diagrams and checkt he front ri ght s eat heat er module LIN Bus circui t,power and ground s uppl y circuit s for short ci rcuit t oground, s hort circuit t o power, open circui t, hi ghresi st anceB1034-01Left front s eat heaterelement general fail ureinformat ion - Generalelectrical fail ure
Element damaged, opencircuitRefer t o t he electrical ci rcuit diagrams and checkt he left front seat heater element circui t for opencircui t
B1035-01Left rear s eat heat erelement general fail ureinformat ion - Generalelectrical fail ure
Element damaged, opencircuitThis DTC wil l onl y log in vali dat ion mode. No hel pt ext requi red
B1036-01Right front seat heaterelement general fail ureinformat ion - Generalelectrical fail ure
Element damaged, opencircuitRefer t o t he electrical ci rcuit diagrams and checkfront ri ght seat heater element circui t for opencircui t