Page 1497 of 4331
EC
NP
O
YES >> Go to
EC-141, " Diagnosis Procedure " .
NO >> INSPECTION END
Wiring Diagram INFOID:0000000004780636
Diagnosis Procedure INFOID:0000000004780064
Page 1498 of 4331
Ground Inspection " .
Is the inspection result normal? YES >> GO TO 2.
NO >> Repair or replace ground connection. YES >> GO TO 4.
NO >> GO TO 3. YES >> GO TO 5.
NO >> Repair open circuit or short to ground or short to power in harness or connectors. Component Inspection " .
Is the inspection result normal? YES >> GO TO 7.
NO >> GO TO 6.
Page 1499 of 4331
EC
NP
O
>> INSPECTION END Diagnosis Procedure " .
>> INSPECTION END
Component Inspection INFOID:0000000004780065YES >> INSPECTION END
NO >> GO TO 2.
Page 1500 of 4331
YES >> Go to
EC-145, " Diagnosis Procedure " .
NO >> INSPECTION END
Page 1501 of 4331
EC
NP
O
Wiring Diagram
INFOID:0000000004780637
Diagnosis Procedure INFOID:0000000004780068
Page 1502 of 4331
YES >> GO TO 3.
NO >> GO TO 2. YES >> GO TO 4.
NO >> Repair open circuit or short to ground or short to power in harness or connectors. Component Inspection " .
Is the inspection result normal? YES >> GO TO 5.
NO >> Replace intake valve timing control solenoid valve. Diagnosis Procedure " .
>> INSPECTION END
Component Inspection INFOID:0000000004780069
Page 1503 of 4331
![NISSAN LATIO 2009 Service Repair Manual P0075 IVT CONTROL SOLENOID VALVE
EC-147
< COMPONENT DIAGNOSIS >
[HR16DE] C
D E
F
G H
I
J
K L
M A EC
NP
O
3. Check resistance between intake valve timing control solenoid
valve terminals as per NISSAN LATIO 2009 Service Repair Manual P0075 IVT CONTROL SOLENOID VALVE
EC-147
< COMPONENT DIAGNOSIS >
[HR16DE] C
D E
F
G H
I
J
K L
M A EC
NP
O
3. Check resistance between intake valve timing control solenoid
valve terminals as per](/manual-img/5/57359/w960_57359-1502.png)
P0075 IVT CONTROL SOLENOID VALVE
EC-147
< COMPONENT DIAGNOSIS >
[HR16DE] C
D E
F
G H
I
J
K L
M A EC
NP
O
3. Check resistance between intake valve timing control solenoid
valve terminals as per the following.
Is the inspection result normal? YES >> GO TO 2.
NO >> Replace intake valve timing control solenoid valve. 2.
CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE-II
1. Remove intake valve timing control solenoid valve.
2. Provide 12 V DC between intake valve timing control solenoid
valve terminals 1 and 2, and then interrupt it. Make sure that the
plunger moves as shown in the figure.
CAUTION:
Do not apply 12 V DC continuously for 5 seconds or more.
Doing so may result in damage to the coil in intake valve
timing control solenoid valve.
NOTE:
Always replace O-ring when intake valve timing control
solenoid valve is removed.
Is the inspection result normal? YES >> INSPECTION END
NO >> Replace intake valve timing control solenoid valve. Terminals Resistance
1 and 2 6.7 - 7.7 Ω [at 20 °C (68 °F)]
1 or 2 and ground ∞
Ω
(Continuity should not exist) PBIB0574E
JMBIA2108ZZ
Page 1504 of 4331
YES >> Go to
EC-151, " Diagnosis Procedure " .
NO-1 >> With CONSULT-III: GO TO 3.
NO-2 >> Without CONSULT-III: GO TO 5. Diagnosis Procedure " .