2005 INFINITI QX4 Factory Service Manual

deactivate passenger airbag horn compression ratio instrument panel ground clearance oil

Page 65 of 3419

INFINITI QX4 2005 Factory Service Manual ACS-56
[ICC]
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: October 20052005 QX56
Symptom 4: The ICC System Is Not Cancelled When the Gear Is in ‘N’EKS00BMN
1. CHECK D RANGE SWITCH
With CONSULT-II
1. W

ACS-56
[ICC]
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: October 20052005 QX56
Symptom 4: The ICC System Is Not Cancelled When the Gear Is in ‘N’EKS00BMN
1. CHECK D RANGE SWITCH
With CONSULT-II
1. With "DATA MONITOR" on the CONSULT-II, check that “NP RANGE SW” operates normally.
OK or NG
OK >> Replace ICC unit and erase DTC. Refer to ACS-60, "ICC Unit" . Perform ICC system running test.
Refer to ACS-9, "
ICC System Running Test" . Then perform self-diagnosis of ICC system again.
NG >> GO TO 2.
2. CHECK CAN COMMUNICATION
With CONSULT-II
1. With CONSULT-II self-diagnosis, check “CAN COMM CIRCUIT”.
OK or NG
OK >> GO TO 3.
NG >> Refer to ACS-38, "
DTC 20 CAN COMM CIRCUIT" .
3. CHECK NP RANGE SWITCH
1. With "DATA MONITOR" on the CONSULT-II, check that “N” position switch operates normally.
OK or NG
OK >> Replace ICC unit. Refer to ACS-60, "ICC Unit" . Perform ICC system running test. Refer to ACS-
9, "ICC System Running Test" . Then perform self-diagnosis of ICC system again.
NG >> Repair or replace as necessary. Perform ICC system running test. Refer to ACS-9, "
ICC System
Running Test" . Then perform self-diagnosis of ICC system again.
Symptom 5: Chime Does Not SoundEKS00BMO
The chime may not sound occasionally in the following cases even if the distance from the vehicle ahead is
short:
When the speed difference from that of the vehicle ahead is small (both vehicles driving at similar speed).
When the vehicle ahead drives at faster speed (the actual distance is increasing).
When depressing the accelerator.
Chime does not sound when the vehicle is not driving.
Chime does not sound when the system does not detect any vehicle ahead. Diagnose the conditions
under which the system is detecting the vehicle ahead and when the system is malfunctioning. If there is
any malfunction in detecting the vehicle ahead. Refer to ACS-57, "
Symptom 7: The ICC System Fre-
quently Cannot Detect the Vehicle Ahead/The Detection Zone is Short" .
1. CHECK ICC WARNING CHIME
With CONSULT-II
1. With "ACTIVE TEST" on the CONSULT-II, check that ICC warning chime operates normally.
OK or NG
OK >> Determine preceding vehicle detection status when malfunction occurred. If chime should have
sounded replace ICC unit. Refer to ACS-60, "
ICC Unit" . Perform ICC system running test. Refer
to ACS-9, "
ICC System Running Test" . Then perform self-diagnosis of ICC system again.
NG >> GO TO 2.

Page 66 of 3419

INFINITI QX4 2005 Factory Service Manual TROUBLE DIAGNOSIS FOR SYMPTOMS
ACS-57
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: October 20052005 QX56
2. CAN COMMUNICATION INSPECTION
With CONSULT-II
1. With CONSULT-II self-diagnosis, check “CAN

TROUBLE DIAGNOSIS FOR SYMPTOMS
ACS-57
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: October 20052005 QX56
2. CAN COMMUNICATION INSPECTION
With CONSULT-II
1. With CONSULT-II self-diagnosis, check “CAN COMM CIRCUIT”.
OK or NG
OK >> Refer to ACS-38, "DTC 20 CAN COMM CIRCUIT" .
NG >> Replace combination meter. Refer to IP-13, "
Combination Meter" . Erase DTC and perform ICC
system running test. Refer to ACS-9, "
ICC System Running Test" . Then perform self-diagnosis of
ICC system again.
Symptom 6: Driving Force Is HuntingEKS00BMP
1. CHECK ECM
1. Perform self-diagnosis of ECM.
OK or NG
OK >> Refer to ACS-57, "Symptom 7: The ICC System Frequently Cannot Detect the Vehicle Ahead/The
Detection Zone is Short" .
NG >> Repair as necessary. Erase DTC and perform ICC system running test. Refer to ACS-9, "
ICC
System Running Test" . Then perform self-diagnosis of ICC system again.
Symptom 7: The ICC System Frequently Cannot Detect the Vehicle Ahead/The
Detection Zone is Short
EKS00BMQ
The detection function may become unstable in the following cases:
When the reflector of the vehicle ahead is small or not clean enough to reflect the laser.
When driving a road with extremely sharp corners.
When the laser cannot detect the reflector of the vehicle ahead as the vehicle ahead is passing a hill or
passing the peak.
1. VISUAL CHECK
1. Check ICC sensor body window for contamination and foreign materials.
OK or NG
OK >> If any contamination or foreign materials are found, remove them. Then perform ICC system run-
ning test. Refer to ACS-9, "
ICC System Running Test" .
NG >> GO TO 2.
2. CHECK FUNCTION
1. After performing laser beam aiming adjustment, perform ICC system running test. Refer to ACS-9, "
ICC
System Running Test" . Check that preceding vehicle detection performance has been improved.
OK or NG
OK >> Inspection End.
NG >>
Replace ICC sensor and perform laser beam aiming adjustment. Refer to ACS-60, "ICC Sen-
sor" .
Perform ICC system running test. Refer to ACS-9, "ICC System Running Test" . Then perform
self-diagnosis of ICC system again.
Symptom 8: The System Does Not Detect the Vehicle Ahead at AllEKS00BMR
1. VISUAL CHECK
1. With ignition switch turned ON (engine not started), check that all indicator lamps in ICC system display
are continuously lit. (Check for a missing segment in preceding vehicle detection display.)
OK or NG
OK >> GO TO 2.
NG >> Check combination meter. Refer to DI-17, "
How to Proceed With Trouble Diagnosis" .

Page 67 of 3419

INFINITI QX4 2005 Factory Service Manual ACS-58
[ICC]
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: October 20052005 QX56
2. VISUAL CHECK
Check ICC sensor body window for contamination and foreign materials.
OK or NG
OK >> If any contamination

Page 68 of 3419

INFINITI QX4 2005 Factory Service Manual ELECTRICAL COMPONENT INSPECTION
ACS-59
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: October 20052005 QX56
ELECTRICAL COMPONENT INSPECTIONPFP:00000
ICC Steering SwitchEKS00BMS
1. Disconnect ICC steering

Page 69 of 3419

INFINITI QX4 2005 Factory Service Manual ACS-60
[ICC]
REMOVAL AND INSTALLATION
Revision: October 20052005 QX56
REMOVAL AND INSTALLATIONPFP:00000
ICC UnitEKS00BMV
ICC SensorEKS00BMW
CAUTION:
Perform the laser beam aiming procedure every time

Page 70 of 3419

INFINITI QX4 2005 Factory Service Manual AP-1
ADJUSTABLE PEDAL
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION AP
A
B
AP
Revision: October 20052005 QX56 ADJUSTABLE PEDAL SYSTEM ............................... 2
Adjustable Pedal ..............

Page 71 of 3419

INFINITI QX4 2005 Factory Service Manual AP-2
ADJUSTABLE PEDAL SYSTEM
Revision: October 20052005 QX56
ADJUSTABLE PEDAL SYSTEMPFP:98800
Adjustable PedalEIS005XL
For adjustable pedal information, refer to SE-11, "AUTOMATIC DRIVE POSITIONER" .

Page 72 of 3419

INFINITI QX4 2005 Factory Service Manual AT-1
AUTOMATIC TRANSMISSION
C TRANSMISSION/TRANSAXLE
CONTENTS
D
E
F
G
H
I
J
K
L
M
SECTION AT
A
B
AT
Revision: October 20052005 QX56 INDEX FOR DTC ....................................................

AT-1
AUTOMATIC TRANSMISSION
C TRANSMISSION/TRANSAXLE
CONTENTS
D
E
F
G
H
I
J
K
L
M
SECTION AT
A
B
AT
Revision: October 20052005 QX56 INDEX FOR DTC ........................................................ 5
Alphabetical Index .................................................... 5
DTC No. Index ......................................................... 6
PRECAUTIONS .......................................................... 7
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 7
Precautions for On Board Diagnostic (OBD) System
of A/T and Engine .................................................... 7
Precautions .............................................................. 8
Service Notice or Precautions .................................. 9
Wiring Diagrams and Trouble Diagnosis .................. 9
PREPARATION ......................................................... 10
Special Service Tools ............................................. 10
Commercial Service Tools ...................................... 12
A/T FLUID ................................................................. 13
Changing A/T Fluid ................................................ 13
Checking A/T Fluid ................................................. 13
A/T Fluid Cooler Cleaning ...................................... 13
A/T CONTROL SYSTEM .......................................... 16
Cross-Sectional View (2WD models) ..................... 16
Cross-Sectional View (4WD models) ..................... 17
Shift Mechanism ..................................................... 18
TCM Function ......................................................... 29
CAN Communication .............................................. 30
Input/Output Signal of TCM .................................... 30
Line Pressure Control ............................................ 31
Shift Control ........................................................... 32
Lock-up Control ...................................................... 33
Engine Brake Control ............................................. 35
Control Valve .......................................................... 35
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 37
Introduction ............................................................ 37
OBD-II Function for A/T System ............................. 37
One or Two Trip Detection Logic of OBD-II ............ 37
OBD-II Diagnostic Trouble Code (DTC) ................. 37
Malfunction Indicator Lamp (MIL) ........................... 40
TROUBLE DIAGNOSIS ............................................ 41
DTC Inspection Priority Chart ................................ 41
Fail-Safe ................................................................. 41How To Perform Trouble Diagnosis For Quick and
Accurate Repair ...................................................... 43
A/T Electrical Parts Location .................................. 48
Circuit Diagram ....................................................... 49
Inspections Before Trouble Diagnosis .................... 50
Check Before Engine is Started .............................. 54
Check at Idle ........................................................... 54
Cruise Test - Part 1 ................................................. 55
Cruise Test - Part 2 ................................................. 57
Cruise Test - Part 3 ................................................. 58
Vehicle Speed When Shifting Gears ...................... 59
Vehicle Speed When Performing and Releasing
Complete Lock-up .................................................. 59
Vehicle Speed When Performing and Releasing
Slip Lock-up ............................................................ 59
Symptom Chart ....................................................... 60
TCM Input/Output Signal Reference Values ........... 82
CONSULT-II Function (A/T) .................................... 83
DTC U1000 CAN COMMUNICATION LINE .............. 95
Description .............................................................. 95
On Board Diagnosis Logic ...................................... 95
Possible Cause ....................................................... 95
DTC Confirmation Procedure ................................. 95
Wiring Diagram — AT — CAN ................................ 96
Diagnostic Procedure ............................................. 98
DTC P0615 START SIGNAL CIRCUIT ..................... 99
Description .............................................................. 99
CONSULT-II Reference Value ................................ 99
On Board Diagnosis Logic ...................................... 99
Possible Cause ....................................................... 99
DTC Confirmation Procedure ................................. 99
Wiring Diagram — AT — STSIG ..........................100
Diagnostic Procedure ...........................................101
DTC P0700 TCM .....................................................103
Description ............................................................103
On Board Diagnosis Logic ....................................103
Possible Cause .....................................................103
DTC Confirmation Procedure ...............................103
Diagnostic Procedure ...........................................103
DTC P0705 PARK/NEUTRAL POSITION SWITCH .104

Load next 8 pages

Page: < prev 1-10 ... 33-40 41-48 49-56 57-64 65-72 73-80 81-88 89-96 97-104 ... 3424 next >

engine oil tire pressure reset transmission fluid trip computer oil viscosity belt