2005 NISSAN X-TRAIL Service Repair Manual

overheating adblue reset oil change technical specifications wheel bolt torque coolant reservoir

Load previous 8 pages

Page 1737 of 4555

NISSAN X-TRAIL 2005 Service Repair Manual FUEL TRANSPORT PUMP
EC-1333
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC

RHD MODELS
TBWA0591E

Page 1738 of 4555

NISSAN X-TRAIL 2005 Service Repair Manual EC-1334
[YD (WITH EURO-OBD)]
FUEL TRANSPORT PUMP

Specification data are reference values, and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring i

Page 1739 of 4555

NISSAN X-TRAIL 2005 Service Repair Manual FUEL TRANSPORT PUMP
EC-1335
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC

2. CHECK FUEL TRASPORT PUMP FUNCTION
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Install suitable

Page 1740 of 4555

NISSAN X-TRAIL 2005 Service Repair Manual EC-1336
[YD (WITH EURO-OBD)]
FUEL TRANSPORT PUMP

5. CHECK FUEL TRANSPORT PUMP POWER SUPPLY AND GROUND CIRCUIT FOR OPEN AND
SHORT
1. Turn ignition switch OFF.
2. Disconnect fuel transport pump harne

Page 1741 of 4555

NISSAN X-TRAIL 2005 Service Repair Manual FUEL TRANSPORT PUMP
EC-1337
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC

10. CHECK TRANSPORT PUMP
Refer to EC-1338, "
Component Inspection" .
OK or NG
OK >> GO TO 14.
NG >> Replace fuel transport

Page 1742 of 4555

NISSAN X-TRAIL 2005 Service Repair Manual EC-1338
[YD (WITH EURO-OBD)]
FUEL TRANSPORT PUMP

Component InspectionEBS011PH
FUEL TRANSPORT PUMP RELAY
Check continuity between terminals 3 and 5 under the following coni-
tions.
FUEL TRANSPORT PUM

Page 1743 of 4555

NISSAN X-TRAIL 2005 Service Repair Manual AUTOMATIC SPEED CONTROL DEVICE (ASCD)
EC-1339
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC

AUTOMATIC SPEED CONTROL DEVICE (ASCD)PFP:18930
System DescriptionEBS01F8C
INPUT/OUTPUT SIGNAL CHART
BASIC

AUTOMATIC SPEED CONTROL DEVICE (ASCD)
EC-1339
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC

AUTOMATIC SPEED CONTROL DEVICE (ASCD)PFP:18930
System DescriptionEBS01F8C
INPUT/OUTPUT SIGNAL CHART
BASIC ASCD SYSTEM
Refer to Owner's Manual for ASCD operating instructions.
Automatic Speed Control Device (ASCD) allows a driver to keep vehicle at predetermined constant speed
without depressing accelerator pedal. Driver can set vehicle speed in advance between approximately 40 km/
h (25 MPH) and 185 km/h (115 MPH).
ECM controls fuel injection value to regulate engine speed.
Operation status of ASCD is indicated by CRUISE indicator and SET indicator in combination meter. If any
malfunction occurs in ASCD system, it automatically deactivates control.
SET OPERATION
Press ASCD MAIN switch. (The CRUISE indicator in combination meter illuminates.)
When vehicle speed reaches a desired speed between approximately 40 km/h (25 MPH) and 185 km/h (115
MPH), press SET switch. (Then SET indicator in combination meter illuminates.)
ACCEL OPERATION
If the RESUME/ACCELERATE switch is depressed during cruise control driving, increase the vehicle speed
until the switch is released or vehicle speed reaches maximum speed controlled by the system.
And then ASCD will keep the new set speed.
CANCEL OPERATION
When any of following conditions exist, cruise operation will be canceled.
CANCEL switch is depressed
More than 2 switches at ASCD steering switch are depressed at the same time (Set speed will be
cleared.).
Brake pedal is depressed
Clutch pedal is depressed or gear position is changed to the neutral position
Vehicle speed increased to 13 km/h higher than the set speed
Vehicle speed decreased to 13 km/h lower than the set speed
ESP system is operated
When the ECM detects any of the following conditions, the ECM will cancel the cruise operation and inform
the driver by blinking indicator lamp.
Malfunction for some self-diagnoses regarding ASCD control: SET lamp will blink quickly.
If MAIN switch is turned to OFF during ASCD is activated, all of ASCD operations will be canceled and vehicle
speed memory will be erased.
COAST OPERATION
When the SET/COAST switch is depressed during cruise control driving, decrease vehicle set speed until the
switch is released. And then ASCD will keep the new set speed.
RESUME OPERATION
When the RESUME/ACCELERATE switch is depressed after cancel operation other than depressing MAIN
switch is performed, vehicle speed will return to last set speed. To resume vehicle set speed, vehicle condition
must meet following conditions.
Brake pedal is released
Clutch pedal is released
Vehicle speed is greater than 40 km/h (25 MPH) and less than 185 km/h (115 MPH)
Sensor Input signal to ECM ECM function Actuator
ASCD brake switch Brake pedal operation
ASCD vehicle speed control Fuel injector and Fuel pump Stop lamp switch Brake pedal operation
ASCD clutch switch Clutch pedal operation
ASCD steering switch ASCD steering switch operation
Combination meter Vehicle speed

Page 1744 of 4555

NISSAN X-TRAIL 2005 Service Repair Manual EC-1340
[YD (WITH EURO-OBD)]
AUTOMATIC SPEED CONTROL DEVICE (ASCD)

Component DescriptionEBS01F8D
ASCD STEERING SWITCH
Refer to EC-1218 .
ASCD BRAKE SWITCH
Refer to EC-1206 and EC-1313 .
ASCD CLUTCH

Load next 8 pages

Page: < prev 1-10 ... 1705-1712 1713-1720 1721-1728 1729-1736 1737-1744 1745-1752 1753-1760 1761-1768 1769-1776 ... 4560 next >

trunk fuel filter key fuse chart fuel reserve clock reset