2005 NISSAN X-TRAIL Service Repair Manual

hood opendisplaystart stop buttonstop startair suspensioninstrument cluster
Popular search:
BRC-26snow chainscheck oilDTC P0444 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVEwheel torquepower steeringjump start terminals
Previous
Next
Load previous 8 pages

Page 2953 of 4555

NISSAN X-TRAIL 2005 Service Repair Manual WHEEL HUB (2WD) RAX-9 C E F G H I J K L MA B RAX NOTE: If a load of 49,030 N (5,000 kg 11,025 lb) cannot be applied, carry out the following actions. Install to drive shaft and tighten wheel hub lo

Page 2954 of 4555

NISSAN X-TRAIL 2005 Service Repair Manual RAX-10 WHEEL HUB (4WD) WHEEL HUB (4WD)PFP:43202 On-Vehicle InspectionEDS00065 Inspect to check that there is no excessive play, cracking, wear, or other damage to rear axle. Turn rear wheels (left/

Page 2955 of 4555

NISSAN X-TRAIL 2005 Service Repair Manual WHEEL HUB (4WD) RAX-11 C E F G H I J K L MA B RAX REMOVAL 1. Remove tyre. 2. Remove wheel hub lock nut. CAUTION: Discard the old hub lock nut; replace with new one. 3. Remove brake caliper from axle

Page 2956 of 4555

NISSAN X-TRAIL 2005 Service Repair Manual RAX-12 WHEEL HUB (4WD) 5. Use a drift (SST) to remove wheel bearing from axle housing. INSPECTION AFTER DISASSEMBLY Wheel Hub Inspect wheel hub for deformation, cracks, and other damage. If any irr

Page 2957 of 4555

NISSAN X-TRAIL 2005 Service Repair Manual WHEEL HUB (4WD) RAX-13 C E F G H I J K L MA B RAX Rotating torque : 1.126 N·m (0.11 kg-m, 10 in-lb) Spring balance reading : 19.70 N (2.01 kg, 4.43 lb)

Page 2958 of 4555

NISSAN X-TRAIL 2005 Service Repair Manual RAX-14 REAR DRIVE SHAFT REAR DRIVE SHAFTPFP:39600 Removal and InstallationEDS000FL REMOVAL 1. Remove axle housing. Refer to RAX-11, "REMOVAL" . NOTE: In order to remove the rear drive shaft assembly

Page 2959 of 4555

NISSAN X-TRAIL 2005 Service Repair Manual REAR DRIVE SHAFT RAX-15 C E F G H I J K L MA B RAX Disassembly and AssemblyEDS000FM DISASSEMBLY Final Drive Side 1. Remove boot bands. 2. Fix shaft to bench vise. CAUTION: When fixing shaft to bench

Page 2960 of 4555

NISSAN X-TRAIL 2005 Service Repair Manual RAX-16 REAR DRIVE SHAFT 4. Screw a drive shaft puller (suitable tool) 30 mm (1.18 in) or more into threaded part of joint sub-assembly. Pull joint sub-assembly out of shaft. CAUTION: If joint sub as
Load next 8 pages
Page:   < prev 1-10 ... 2921-2928 2929-2936 2937-2944 2945-2952 2953-2960 2961-2968 2969-2976 2977-2984 2985-2992 ... 4560 next >
maintenance resetfuel fill door releasejump cablegarage door openerauxiliary battery locationautomatic transmission
Popular search:
headlightturn signal bulbfuse diagramground clearanceengine coolant temperature sensorinterior filtercenter console