Page 1745 of 4555
ASCD INDICATOR
EC-1341
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC
ASCD INDICATORPFP:24814
Component DescriptionEBS01F8E
ASCD indicator lamp illuminates to indicate ASCD operation status. The Lamp has two indicators, CRUISE
and SET, and is integrated in combination meter.
CRUISE indicator illuminates when MAIN switch on ASCD steering switch is turned ON to indicated that
ASCD system is ready for operation.
SET indicator illuminates when the following conditions are met.
CRUISE indicator is illuminated.
SET/COAST switch on ASCD steering switch is turned ON while vehicle speed is within the range of
ASCD setting.
SET indicator remains lit during ASCD control.
Refer to EC-1339, "
AUTOMATIC SPEED CONTROL DEVICE (ASCD)" for the ASCD function.
Page 1746 of 4555
EC-1342
[YD (WITH EURO-OBD)]
ASCD INDICATOR
Wiring Diagram—LHD ModelsEBS01F8F
TBWB0478E
Page 1747 of 4555
ASCD INDICATOR
EC-1343
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC
Wiring Diagram—RHD ModelsEBS01F8G
TBWB0647E
Page 1748 of 4555
EC-1344
[YD (WITH EURO-OBD)]
ASCD INDICATOR
Diagnostic ProcedureEBS01F8H
1. CHECK OVERALL FUNCTION
Check ASCD indicator under the following conditions.
OK or NG
OK >>INSPECTION END
NG >> GO TO 2.
2. CHECK DTC
Check that DTC U1000 is not displayed.
OK or NG
OK >> Perform trouble diagnoses for DTC U1000. Refer to EC-1056, "DTC U1000 CAN COMMUNICA-
TION LINE" .
NG >> GO TO 3.
3. CHECK COMBINATION METER OPERATION
Does combination meter operate normally?
Ye s o r N o
Yes >> GO TO 4.
No >> Check combination meter circuit. Refer to DI-4, "
COMBINATION METERS" .
4. CHECK INTERMITTENT INCIDENT
Refer to EC-1045, "
TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT" .
>>INSPECTION END
ASCD INDICATOR CONDITION SPECIFICATION
CRUISE LAMP
Ignition switch: ONMAIN switch: Pressed at the
first time→at the 2nd timeON→OFF
SET LAMP
MAIN switch: ON
When vehicle speed is
between 40 km/h (25 MPH)
and 185 km/h (115 MPH)
COAST/SET switch pressed ON
COAST/SET switch released OFF
Page 1749 of 4555
START SIGNAL
EC-1345
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC
START SIGNALPFP:48750
Wiring DiagramEBS011GG
TBWA0582E
Page 1750 of 4555
![NISSAN X-TRAIL 2005 Service Repair Manual EC-1346
[YD (WITH EURO-OBD)]
START SIGNAL
Diagnostic ProcedureEBS011GH
1. CHECK START SIGNAL OVERALL FUNCTION
With CONSULT-II
1. Turn ignition switch ON.
2. Check “START SIGNAL” in “DATA MONI NISSAN X-TRAIL 2005 Service Repair Manual EC-1346
[YD (WITH EURO-OBD)]
START SIGNAL
Diagnostic ProcedureEBS011GH
1. CHECK START SIGNAL OVERALL FUNCTION
With CONSULT-II
1. Turn ignition switch ON.
2. Check “START SIGNAL” in “DATA MONI](/manual-img/5/57403/w960_57403-1749.png)
EC-1346
[YD (WITH EURO-OBD)]
START SIGNAL
Diagnostic ProcedureEBS011GH
1. CHECK START SIGNAL OVERALL FUNCTION
With CONSULT-II
1. Turn ignition switch ON.
2. Check “START SIGNAL” in “DATA MONITOR” mode with CON-
SULT-II under the following conditions.
Without CONSULT-II
Check voltage between ECM terminal 99 and ground under the fol-
lowing conditions.
OK or NG
OK >>INSPECTION END
NG >> GO TO 2.
2. CHECK START SIGNAL INPUT SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector and ignition switch harness connector.
3. Check harness continuity between ECM terminal 99 and ignition switch terminal 6.
Refer to Wiring Diagram.
4. Also check harness for short to ground and short to power.
OK or NG
OK >> GO TO 4.
NG >> GO TO 3.
3. DETECT MALFUNCTIONING PART
Check the following.
10A fuse
Fuse block (J/B) connectors M1, E102
Harness for open or short between ECM and ignition switch
>> Repair open circuit or short to ground or short to power in harness or connectors.
Condition START SIGNAL
Ignition switch ON OFF
Ignition switch START ON
PBIB0433E
Condition Voltage
Ignition switch ON Approximately 0V
Ignition switch START Battery voltage
PBIB1949E
Continuity should exist.
Page 1751 of 4555
START SIGNAL
EC-1347
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC
4. CHECK INTERMITTENT INCIDENT
Refer to EC-1045, "
TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT" .
>>INSPECTION END
Page 1752 of 4555
EC-1348
[YD (WITH EURO-OBD)]
MI & DATA LINK CONNECTORS
MI & DATA LINK CONNECTORSPFP:24814
Wiring DiagramEBS011GI
LHD MODELS
TBWA0585E