Page 2705 of 4555
REPAIR FOR COMPONENT PARTS
AT-441
[ALL]
D
E
F
G
H
I
J
K
L
MA
B
AT
3. Drive and pull out parking rod plate retaining pin.
4. Remove parking rod plate (with parking rod) from manual shaft.
5. Draw out parking rod (with parking rod plate) from transaxle
case.
6. Remove parking rod from parking rod plate.
7. Pull out manual shaft retaining pin.
8. Remove manual shaft and manual plate from transaxle case.
9. Remove manual shaft oil seal.
CAUTION:
Be careful not to scratch transaxle case.
INSPECTION
Check component parts for wear or damage. Replace if necessary.
INSTALLATION
1. Use a drift [commercial service tool φ 22 mm (0.87 in)] to drive
manual shaft oil seal into the transaxle case.
CAUTION:
Do not reuse manual shaft oil seal.
Apply ATF to outer surface of manual shaft oil seal.
2. Install parking rod to parking rod plate.
SAT043FC
SAT049F
SAT080D
SAT081D
Page 2706 of 4555
AT-442
[ALL]
REPAIR FOR COMPONENT PARTS
3. Install manual shaft and manual plate.
4. Install parking rod plate (with parking rod) on manual shaft.
5. Align groove of manual shaft and hole of transaxle case.
6. Install manual shaft retaining pin up to bottom of hole.
CAUTION:
Do not reuse retaining pin.
7. Set parking rod plate onto manual shaft and drive retaining pin.
CAUTION:
Both ends of pin should protrude.
Do not reuse retaining pin.
8. Install manual plate retaining pin.
CAUTION:
Both ends of pin should protrude.
Do not reuse retaining pin.
9. Install detente spring on transaxle case. Tighten detente spring
fitting bolt to the specified torque. Refer to AT- 4 4 0 , "
COMPO-
NENTS" .
SCIA3627E
SAT045FC
SAT034JA
SAT047FC
SAT042F
Page 2707 of 4555
REPAIR FOR COMPONENT PARTS
AT-443
[ALL]
D
E
F
G
H
I
J
K
L
MA
B
AT
Oil PumpECS00EC0
COMPONENTS
DISASSEMBLY
1. Remove seal rings.
2. Loosen bolts in a crisscross pattern and remove oil pump cover.
1. Oil pump housing oil seal 2. Oil pump housing 3. O-ring
4. Outer gear 5. Inner gear 6. Oil pump cover
7. Seal ring
SCIA3341E
ATM0090D
SAT051F
Page 2708 of 4555
AT-444
[ALL]
REPAIR FOR COMPONENT PARTS
3. Remove inner and outer gear from oil pump housing.
4. Remove O-ring from oil pump housing.
5. Remove oil pump housing oil seal.
CAUTION:
Be careful not to scratch oil pump housing.
SAT092D
SCIA2841E
SAT094D
Page 2709 of 4555
![NISSAN X-TRAIL 2005 Service Repair Manual REPAIR FOR COMPONENT PARTS
AT-445
[ALL]
D
E
F
G
H
I
J
K
L
MA
B
AT
INSPECTION
Oil Pump Housing, Oil Pump Cover, Inner Gear and Outer Gear
Check for wear or damage.
Side Clearances
Measure the side NISSAN X-TRAIL 2005 Service Repair Manual REPAIR FOR COMPONENT PARTS
AT-445
[ALL]
D
E
F
G
H
I
J
K
L
MA
B
AT
INSPECTION
Oil Pump Housing, Oil Pump Cover, Inner Gear and Outer Gear
Check for wear or damage.
Side Clearances
Measure the side](/manual-img/5/57403/w960_57403-2708.png)
REPAIR FOR COMPONENT PARTS
AT-445
[ALL]
D
E
F
G
H
I
J
K
L
MA
B
AT
INSPECTION
Oil Pump Housing, Oil Pump Cover, Inner Gear and Outer Gear
Check for wear or damage.
Side Clearances
Measure the side clearance of inner and outer gears in at least
four places around each outside edge. Maximum measured val-
ues should be within specified positions.
If the clearance is less than standard, select inner and outer
gear as a set so that clearance is within specifications. Refer to
AT- 5 3 0 , "
SERVICE DATA AND SPECIFICATIONS (SDS)" .
If the clearance is more than standard, replace whole oil pump
assembly except oil pump cover.
Measure the clearance between outer gear and oil pump hous-
ing.
If not within allowable limit, replace whole oil pump assembly
except oil pump cover.
Seal Ring Clearance
Measure the clearance between seal ring and ring groove.
If not within allowable limit, replace oil pump cover assembly.Standard clearance: 0.030 - 0.050 mm (0.0012 - 0.0020 in)
SAT095D
Standard clearance: 0.111 - 0.181 mm (0.0044 - 0.0071 in)
Allowable limit: 0.181 mm (0.0071 in)
SAT096D
Standard clearance: 0.1 - 0.25 mm (0.0039 - 0.0098 in)
Allowable limit: 0.25 mm (0.0098 in)
SAT097D
Page 2710 of 4555
AT-446
[ALL]
REPAIR FOR COMPONENT PARTS
ASSEMBLY
1. Install oil pump housing oil seal on oil pump housing.
CAUTION:
Do not reuse oil pump housing oil seal.
Apply ATF to outer surface of oil pump housing oil seal.
2. Install O-ring on oil pump housing.
CAUTION:
Do not reuse O-ring.
Apply ATF to O-ring.
3. Install inner and outer gears on oil pump housing.
CAUTION:
Be careful of the direction of inner gear.
4. Install oil pump cover on oil pump housing.
a. Wrap masking tape around splines of oil pump cover assembly
to protect seal. Position oil pump cover assembly on oil pump
housing assembly, then remove masking tape.
b. Tighten bolts in a crisscross pattern. Tighten oil pump cover
bolts to the specified torque. Refer to AT- 4 4 3 , "
COMPONENTS"
.
SAT900DA
SCIA2841E
SAT092D
SAT051F
Page 2711 of 4555
REPAIR FOR COMPONENT PARTS
AT-447
[ALL]
D
E
F
G
H
I
J
K
L
MA
B
AT
5. Install new seal rings carefully after packing ring groove with
petroleum jelly.
CAUTION:
Do not spread the gap of seal ring excessively while
installing. The ring may be deformed.
Do not reuse seal rings.
Apply petroleum jelly to seal rings.
SCIA3638E
Page 2712 of 4555
AT-448
[ALL]
REPAIR FOR COMPONENT PARTS
Control Valve AssemblyECS00EC1
COMPONENTS
1. Oil strainer 2. O-ring 3. Snap ring
4. Terminal body 5. O-ring 6. Solenoid valve assembly
7. Control valve lower body 8. Oil cooler relief valve spring 9. Check ball
10. Separating plate 11. Support plate 12. Steel ball
13. Control valve inter body 14. Pilot filter 15. Separating plate
16. Steel ball 17. Control valve upper body
SCIA4973E