Page 57 of 3171

TROUBLE DIAGNOSIS
AT-49
D
E
F
G
H
I
J
K
L
MA
B
AT
3.CHECK SHIFT-UP D2®D3
Press down accelerator pedal about half-way and inspect if the vehicle shifts up (D2®D3) at the appropriate
speed. Refer toAT-52, "
Vehicle Speed at Which Gear Shifting Occurs".
With CONSULT-II
Read the gear position, throttle degree and vehicle speed. Refer toAT-83, "
DATA MONITOR MODE".
Does the A/T shift-up D
2®D3at the correct speed?
YES >> GO TO 4.
NO >> Enter a check mark at “A/T Does Not Shift: D
2®D3”onAT-38, "DIAGNOSTIC WORKSHEET",
then continue the road test.
4.CHECK SHIFT-UP D3®D4
Press down accelerator pedal about half-way and inspect if the vehicle shifts up (D3®D4) at the appropriate
speed. Refer toAT-52, "
Vehicle Speed at Which Gear Shifting Occurs".
With CONSULT-II
Read the gear position, throttle degree and vehicle speed. Refer toAT-83, "
DATA MONITOR MODE".
Does the A/T shift-up D
3®D4at the correct speed?
YES >> GO TO 5.
NO >> Enter a check mark at “A/T Does Not Shift: D
3®D4”onAT-38, "DIAGNOSTIC WORKSHEET",
then continue the road test.
5.CHECK SHIFT-UP D4®D5
Press down accelerator pedal about half-way and inspect if the vehicle shifts up (D4®D5) at the appropriate
speed. Refer toAT-52, "
Vehicle Speed at Which Gear Shifting Occurs".
With CONSULT-II
Read the gear position, throttle degree and vehicle speed. Refer toAT-83, "
DATA MONITOR MODE".
Does the A/T shift-up D
4®D5at the correct speed?
YES >> GO TO 6.
NO >> Enter a check mark at “A/T Does Not Shift: D
4®D5”onAT-38, "DIAGNOSTIC WORKSHEET",
then continue the road test.
6.CHECK LOCK-UP
When releasing accelerator pedal (closed throttle position signal: OFF) from D
5, check lock-up from D5to L/
U. Refer toAT-52, "
Vehicle Speed at Which Gear Shifting Occurs".
With CONSULT-II
Select “TCC SOLENOID” with “MAIN SIGNALS” mode for “A/T”. Refer toAT-77, "
CONSULT-II REFERENCE
VA L U E".
Does it lock-up?
YES >> GO TO 7.
NO >> Enter a check mark at “A/T Does Not Perform Lock-up” onAT- 3 8 , "
DIAGNOSTIC WORKSHEET"
, then continue the road test.
7.CHECK LOCK-UP HOLD
Check hold lock-up.
With CONSULT-II
Select “TCC SOLENOID” with “MAIN SIGNALS” mode for “A/T”. Refer toAT-77, "
CONSULT-II REFERENCE
VA L U E".
Does it maintain lock-up status?
YES >> GO TO 8.
NO >> Enter a check mark at “A/T Does Not Hold Lock-up Condition” onAT-38, "
DIAGNOSTIC WORK-
SHEET", then continue the road test.
Page 58 of 3171

AT-50
TROUBLE DIAGNOSIS
8.CHECK LOCK-UP RELEASE
Check lock-up cancellation by depressing brake pedal lightly to decelerate.
With CONSULT-II
Select “TCC SOLENOID” with “MAIN SIGNALS” mode for “A/T”. Refer toAT-77, "
CONSULT-II REFERENCE
VA L U E".
Does lock-up cancel?
YES >> GO TO 9.
NO >> Enter a check mark at “Lock-up Is Not Released” onAT-38, "
DIAGNOSTIC WORKSHEET",then
continue the road test.
9.CHECK SHIFT-DOWN D5®D4
Decelerate by pressing lightly on brake pedal.
With CONSULT-II
Read the gear position and engine speed. Refer toAT-83, "
DATA MONITOR MODE".
When the A/T shift-down D
5®D4, does the engine speed drop smoothly back to idle?
YES >> 1. Stop the vehicle.
2. Go toAT-50, "
Cruise Test - Part 2".
NO >> Enter a check mark at “Engine Speed Does Not Return to Idle” onAT-38, "
DIAGNOSTIC WORK-
SHEET", then continue the road test. Go toAT-50, "Cruise Test - Part 2".
CruiseTest-Part2ECS00FX4
1.CHECK STARTING FROM D1
1. Move selector lever to “D” position.
2. Accelerate at half throttle.
With CONSULT-II
Read the gear position. Refer toAT-83, "
DATA MONITOR MODE".
Does it start from D
1?
YES >> GO TO 2.
NO >> Enter a check mark at “Vehicle Cannot Be Started from D
1”onAT-38, "DIAGNOSTIC WORK-
SHEET", then continue the road test.
2.CHECK SHIFT-UP D1®D2
Press accelerator pedal down all the way and inspect whether or not the A/T shifts up (D1®D2)atthecor-
rect speed. Refer toAT-52, "
Vehicle Speed at Which Gear Shifting Occurs".
With CONSULT-II
Read the gear position, throttle degree and vehicle speed. Refer toAT-83, "
DATA MONITOR MODE".
Does the A/T shift-up D
1®D2at the correct speed?
YES >> GO TO 3.
NO >> Enter a check mark at “A/T Does Not Shift: D
1®D2”onAT-38, "DIAGNOSTIC WORKSHEET",
then continue the road test.
3.CHECK SHIFT-UP D2®D3
Press accelerator pedal down all the way and inspect whether or not the A/T shifts up (D2®D3)atthecor-
rect speed. Refer toAT-52, "
Vehicle Speed at Which Gear Shifting Occurs".
With CONSULT-II
Read the gear position, throttle degree and vehicle speed. Refer toAT-83, "
DATA MONITOR MODE".
Does the A/T shift-up D
2®D3at the correct speed?
YES >> GO TO 4.
NO >> Enter a check mark at “A/T Does Not Shift: D
2®D3”onAT-38, "DIAGNOSTIC WORKSHEET",
then continue the road test.
Page 59 of 3171

TROUBLE DIAGNOSIS
AT-51
D
E
F
G
H
I
J
K
L
MA
B
AT
4.CHECK SHIFT-UP D3®D4AND ENGINE BRAKE
When the A/T changes speed D
3®D4, return accelerator pedal.
With CONSULT-II
Read the gear position. Refer toAT-83, "
DATA MONITOR MODE".
Does the A/T shift-up D
3®D4and apply the engine brake?
YES >> 1. Stop the vehicle.
2. Go toAT-51, "
Cruise Test - Part 3".
NO >> Enter a check mark at “A/T Does Not Shift: D
3®D4”onAT-38, "DIAGNOSTIC WORKSHEET",
then continue the road test. Go toAT-51, "
Cruise Test - Part 3".
Cruise Test - Part 3ECS00FX5
1.CHECK SHIFT-DOWN
1. Confirm overdrive control switch is ON position.
2. Confirm gear selector lever is in “D” position.
3. Accelerate vehicle using half-throttle to D
5.
4. Release accelerator pedal.
5. Set overdrive control switch to OFF position while driving in D
5.
With CONSULT-II
Read the gear position. Refer toAT-83, "
DATA MONITOR MODE".
Does A/T shift from D
5to D4(OD OFF)?
YES >> GO TO 2.
NO >> Enter a check mark at “A/T does not shift: 5th gear®4th gear” on theAT-38, "
DIAGNOSTIC
WORKSHEET", then continue the road test.
2.CHECK SHIFT-DOWN
During D
4driving, is downshift from “D”®“3”®“2”®“1” performed?
With CONSULT-II
Read the gear position. Refer toAT-83, "
DATA MONITOR MODE".
Is downshifting correctly performed?
YES >> GO TO 3.
NO >> Enter a check mark at “A/T does not shift” at the corresponding position (4th®3rd, 3rd®2nd,
2nd®1st) on theAT-38, "
DIAGNOSTIC WORKSHEET", then continue the road test.
3.CHECK ENGINE BRAKE
Check engine brake.
Does engine braking effectively reduce speed in 1
1position?
YES >> 1. Stop the vehicle.
2. Perform self-diagnosis. Refer toAT-80, "
SELF-DIAGNOSTIC RESULT MODE",AT-89, "Diag-
nostic Procedure Without CONSULT-II".
NO >> Enter a check mark at “Vehicle Does Not Decelerate by Engine Brake” on theAT-38, "
DIAGNOS-
TIC WORKSHEET", then continue trouble diagnosis.
Page 60 of 3171

AT-52
TROUBLE DIAGNOSIS
Vehicle Speed at Which Gear Shifting Occurs
ECS00FX6
2WD MODELS
lAt half throttle, the accelerator opening is 4/8 of the full opening.
4WD MODELS
lAt half throttle, the accelerator opening is 4/8 of the full opening.
Vehicle Speed at Which Lock-up Occurs/ReleasesECS00FX7
2WD MODELS
lAt closed throttle, the accelerator opening is less than 1/8 condition. (Closed throttle position signal: OFF)
lAt half throttle, the accelerator opening is 4/8 of the full opening.
4WD MODELS
lAt closed throttle, the accelerator opening is less than 1/8 condition. (Closed throttle position signal: OFF)
lAt half throttle, the accelerator opening is 4/8 of the full opening.Tire sizeThrottle
positionVehicle speed [km/h (MPH)]
D
1®D2D2®D3D3®D4D4®D5D5®D4D4®D3D3®D2D2®D1
255/65 R17
255/70 R16Full
throttle41 - 45
(25 - 28)66 - 72
(41 - 45)103 - 113
(64 - 70)148 - 164
(92 - 102)144 - 160
(89 - 99)92 - 102
(57 - 63)53 - 59
(33 - 37)23 - 24
(14 - 15)
Half
throttle34 - 38
(21 - 24)55 - 61
(34 - 38)86 - 96
(53 - 60)118 - 130
(73 - 81)88 - 98
(55 - 61)60 - 66
(37 - 41)39 - 43
(24 - 27)10 - 11
(6 - 7)
Tire sizeThrottle
positionVehiclespeed [km/h(MPH)]
D1®D2D2®D3D3®D4D4®D5D5®D4D4®D3D3®D2D2®D1
255/65 R17
255/70 R16Full
throttle38 - 42
(24 - 26)62 - 68
(39 - 42)97 - 107
(60 - 66)141 - 155
(88 - 96)137 - 151
(85 - 94)87 - 97
(54 - 60)50 - 56
(31 - 35)22 - 24
(14 - 15)
Half
throttle32 - 36
(20 - 22)52 - 58
(32 - 36)82 - 90
(51 - 56)117 - 129
(73 - 80)83 - 91
(52 - 57)57 - 63
(35 - 39)37 - 41
(23 - 25)10 - 11
(6 - 7)
265/70 R16LTFull
throttle40 - 44
(25 - 27)65 - 71
(40 - 44)101 - 111
(63 - 69)145 - 161
(90 - 100)142 - 156
(88 - 97)90 - 100
(56 - 62)52 - 58
(32 - 36)23 - 25
(14 - 16)
Half
throttle33 - 37
(21 - 23)54 - 60
(34 - 37)85 - 93
(53 - 58)121 - 133
(75 - 83)85 - 95
(53 - 59)59 - 65
(37 - 40)38 - 42
(24 - 26)10 - 11
(6 - 7)
Tire size Throttle positionVehicle speed [km/h (MPH)]
Lock-up ON Lock-up OFF
255/65 R17
255/70 R16Closed throttle 73 - 81 (45 - 50) 70 - 78 (44 - 48)
Half throttle 141 - 155 (88 - 96) 130 - 144 (81 - 89)
Tire size Throttle positionVehicle speed [km/h (MPH)]
Lock-up ON Lock-up OFF
255/65 R17
255/70 R16Closed throttle 69 - 77 (43 - 48) 66 - 74 (41 - 46)
Half throttle 134 - 148 (83 - 92) 123 - 137 (76 - 85)
265/70 R16LTClosed throttle 72 - 80 (45 - 50) 69 - 77 (43 - 48)
Half throttle 139 - 153 (86 - 95) 128 - 142 (80 - 88)
Page 61 of 3171

TROUBLE DIAGNOSIS
AT-53
D
E
F
G
H
I
J
K
L
MA
B
AT
Symptom ChartECS00FX8
lThe diagnostic item numbers show the sequence for inspection. Inspect in order from item 1.
lOverhaul and inspect inside the A/T only if A/T fluid condition is NG. Refer toAT-43, "A/T Fluid Con-
dition Check".
No. Items Symptom Condition Diagnostic ItemReference
page
1
Shift
ShockLarge shock. (“N”®“D”
position)
Refer toAT-180,
"Large Shock (“N”to
“D”Position)".ON vehicle1. Engine idle speedEC-38
2. Engine speed signalAT-108
3. Accelerator pedal position sensorAT- 11 6
4. Control cable adjustmentAT- 2 11
5. A/T fluid temperature sensorAT- 11 8
6. ATF pressure switch 1 and front brake solenoid valveAT-156,
AT-137
7. CAN communication lineAT- 9 1
8. A/T fluid level and stateAT- 4 3
9. Line pressure testAT- 4 4
10. Control valve with TCMAT-218
OFF vehicle11. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer toAT- 1 4 , "Cross-
Sectional View (2WD Models)",AT- 1 5 , "Cross-Sectional View
(4WD Models)".)AT-263
2Shock is too large
when changing D1
®D2.ON vehicle1. Accelerator pedal position sensorAT- 11 6
2. Control cable adjustmentAT- 2 11
3. ATF pressure switch 5 and direct clutch solenoid valveAT-160,
AT-142
4. CAN communication lineAT- 9 1
5. Engine speed signalAT-108
6. Turbine revolution sensorAT-123
7. Vehicle speed sensor A/T and vehicle speed sensor MTRAT-103,
AT-125
8. A/T fluid level and stateAT- 4 3
9. Control valve with TCMAT-218
OFF vehicle 10. Direct clutchAT-298
3Shock is too large
when changing D2
®D3.ON vehicle1. Accelerator pedal position sensorAT- 11 6
2. Control cable adjustmentAT- 2 11
3. ATF pressure switch 6 and high and low reverse clutch
solenoid valveAT-162,
AT-147
4. CAN communication lineAT- 9 1
5. Engine speed signalAT-108
6. Turbine revolution sensorAT-123
7. Vehicle speed sensor A/T and vehicle speed sensor MTRAT-103,
AT-125
8. A/T fluid level and stateAT- 4 3
9. Control valve with TCMAT-218
OFF vehicle 10. High and low reverse clutchAT-296
Page 62 of 3171

AT-54
TROUBLE DIAGNOSIS
4
Shift
ShockShockistoolarge
when changing D3
®D4.ON vehicle1. Accelerator pedal position sensorAT- 11 6
2. Control cable adjustmentAT- 2 11
3. ATF pressure switch 3 and input clutch solenoid valveAT- 1 5 8,
AT- 1 3 2
4. CAN communication lineAT- 9 1
5. Engine speed signalAT- 1 0 8
6. Turbine revolution sensorAT- 1 2 3
7. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 3,
AT- 1 2 5
8. A/T fluid level and stateAT- 4 3
9. Control valve with TCMAT- 2 1 8
OFF vehicle 10. Input clutchAT- 2 8 6
5Shockistoolarge
when changing D4
®D5.ON vehicle1. Accelerator pedal position sensorAT- 11 6
2. Control cable adjustmentAT- 2 11
3. ATF pressure switch 1 and front brake solenoid valveAT- 1 5 6,
AT- 1 3 7
4. CAN communication lineAT- 9 1
5. Engine speed signalAT- 1 0 8
6. Turbine revolution sensorAT- 1 2 3
7. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 3,
AT- 1 2 5
8. A/T fluid level and stateAT- 4 3
9. Control valve with TCMAT- 2 1 8
OFF vehicle10. Front brake (brake band)AT- 2 5 111. Input clutchAT- 2 8 6
6Shockistoolargefor
downshift when accel-
erator pedal is
pressed.ON vehicle1. Accelerator pedal position sensorAT- 11 6
2. Control cable adjustmentAT- 2 11
3. CAN communication lineAT- 9 1
4. Engine speed signalAT- 1 0 8
5. Turbine revolution sensorAT- 1 2 3
6. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 3,
AT- 1 2 5
7. A/T fluid level and stateAT- 4 3
8. Control valve with TCMAT- 2 1 8
OFF vehicle9. Front brake (brake band)AT- 2 5 110. Input clutchAT- 2 8 6
11. High and low reverse clutchAT- 2 9 6
12. Direct clutchAT- 2 9 8
No. Items Symptom Condition Diagnostic ItemReference
page
Page 63 of 3171

TROUBLE DIAGNOSIS
AT-55
D
E
F
G
H
I
J
K
L
MA
B
AT
7
Shift
ShockShock is too large for
upshift when accelera-
tor pedal is released.ON vehicle1. Accelerator pedal position sensorAT- 11 6
2. Control cable adjustmentAT- 2 11
3. Engine speed signalAT-108
4. CAN communication lineAT- 9 1
5. Turbine revolution sensorAT-123
6. Vehicle speed sensor A/T and vehicle speed sensor MTRAT-103,
AT-125
7. A/T fluid level and stateAT- 4 3
8. Control valve with TCMAT-218
OFF vehicle9. Front brake (brake band)AT-25110. Input clutchAT-286
11. High and low reverse clutchAT-296
12. Direct clutchAT-298
8Shock is too large for
lock-up.ON vehicle1. Accelerator pedal position sensorAT- 11 6
2. Control cable adjustmentAT- 2 11
3. Engine speed signalAT-108
4. CAN communication lineAT- 9 1
5. Turbine revolution sensorAT-123
6. Vehicle speed sensor A/T and vehicle speed sensor MTRAT-103,
AT-125
7. Torque converter clutch solenoid valveAT- 11 0
8. A/T fluid level and stateAT- 4 3
9. Control valve with TCMAT-218
OFF vehicle 10. Torque converterAT-263
9Shock is too large dur-
ing engine brake.ON vehicle1. Accelerator pedal position sensorAT- 11 6
2. Control cable adjustmentAT- 2 11
3. CAN communication lineAT- 9 1
4. A/T fluid level and stateAT- 4 3
5. Control valve with TCMAT-218
OFF vehicle6. Front brake (brake band)AT-2517. Input clutchAT-286
8. High and low reverse clutchAT-296
9. Direct clutchAT-298
No. Items Symptom Condition Diagnostic ItemReference
page
Page 64 of 3171

AT-56
TROUBLE DIAGNOSIS
10
No Up
ShiftGear does not change
from D
1®D2or from.
Refer toAT-188, "
A/T
Does Not Shift: D1®
D2".ON vehicle1. A/T fluid level and stateAT- 4 3
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 3,
AT- 1 2 5
3. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 6 0,
AT- 1 4 2
4. Line pressure testAT- 4 4
5. CAN communication lineAT- 9 1
6. Control valve with TCMAT- 2 1 8
OFF vehicle 7. Direct clutchAT- 2 9 8
11Gear does not change
from D2®D3or from.
Refer toAT-190, "
A/T
Does Not Shift: D2®
D3".ON vehicle1. A/T fluid level and stateAT- 4 3
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 3,
AT- 1 2 5
3. ATF pressure switch 6 and high and low reverse clutch
solenoid valveAT- 1 6 2,
AT- 1 4 7
4. Line pressure testAT- 4 4
5. CAN communication lineAT- 9 1
6. Control valve with TCMAT- 2 1 8
OFF vehicle 7. High and low reverse clutchAT- 2 9 6
12Gear does not change
from D
3®D4or from.
Refer toAT-192, "
A/T
Does Not Shift: D3®
D4".ON vehicle1. A/T fluid level and stateAT- 4 3
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 3,
AT- 1 2 5
3. ATF pressure switch 3 and input clutch solenoid valveAT- 1 5 8,
AT- 1 3 2
4. ATF pressure switch 1 and front brake solenoid valveAT- 1 5 6,
AT- 1 3 7
5. Line pressure testAT- 4 4
6. CAN communication lineAT- 9 1
7. Control valve with TCMAT- 2 1 8
OFF vehicle 8. Input clutchAT- 2 8 6
13Gear does not change
from D
4®D5or from.
Refer toAT-194, "
A/T
Does Not Shift: D4®
D5".ON vehicle1. A/T fluid level and stateAT- 4 3
2. Overdrive control switchAT- 1 7 2
3. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 3,
AT- 1 2 5
4. ATF pressure switch 1 and front brake solenoid valveAT- 1 5 6,
AT- 1 3 7
5. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 6 0,
AT- 1 4 2
6. Turbine revolution sensorAT- 1 2 3
7. Line pressure testAT- 4 4
8. CAN communication lineAT- 9 1
9. Control valve with TCMAT- 2 1 8
OFF vehicle10. Front brake (brake band)AT- 2 6 311. Input clutchAT- 2 8 6
No. Items Symptom Condition Diagnostic ItemReference
page