Page 25 of 4647
![INFINITI M35 2007 Factory Service Manual ACS-16
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: 2007 April2007 M35/M45
2. Adjust the height of the target board with aligning the upside tip
of the triangle scale with the center of laser beam axi INFINITI M35 2007 Factory Service Manual ACS-16
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: 2007 April2007 M35/M45
2. Adjust the height of the target board with aligning the upside tip
of the triangle scale with the center of laser beam axi](/manual-img/42/57024/w960_57024-24.png)
ACS-16
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: 2007 April2007 M35/M45
2. Adjust the height of the target board with aligning the upside tip
of the triangle scale with the center of laser beam axis.
NOTE:
The center of laser beam axis is located at 92 mm (3.62 in) from
the right edge and 22 mm (0.87 in) from the top of the ICC sen-
sor integrated unit from a front view of vehicle.
ADJUSTING THE RIGHT-LEFT POSITION OF THE TARGET
1. Attach a scale [at least 350 mm (14 in) or longer] or stick as
shown in the figure.
2. Suspend a thread with weight on the tip of the thread to 266 mm
(10.47 in) right side of the target board from the center of the
target board on top.
SETTING THE TARGET
1. Suspend a thread with weight on tip to splice the center of the front and rear bumpers. Then, mark the
center point on the ground as each weight points.
2. Link the front and rear bumpers center points marked on the ground, and mark a point 3.9 m (12.8 ft)
ahead of the front bumper, on the extended line of the previous link line of the bumper center points.
Then, adjust the position of the target board so that the weight come on the top of the marked point [3.9 m
(12.8 ft) ahead of the front bumper] and face to the vehicle.
PKIB4486J
PKIB8352E
PKIB8353E
PKIB8354E
Page 26 of 4647
![INFINITI M35 2007 Factory Service Manual LASER BEAM AIMING ADJUSTMENT
ACS-17
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
3. Adjust the position of the target board so that the extended line
that links the center of the INFINITI M35 2007 Factory Service Manual LASER BEAM AIMING ADJUSTMENT
ACS-17
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
3. Adjust the position of the target board so that the extended line
that links the center of the](/manual-img/42/57024/w960_57024-25.png)
LASER BEAM AIMING ADJUSTMENT
ACS-17
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
3. Adjust the position of the target board so that the extended line
that links the center of the rear window glass (the center of the
rear window defogger pattern) and the center of the windshield
(the setting part of the room mirror) align with the weight sus-
pended from the board.
4. Remove the thread suspended to the right side of board and
suspend a thread with weight on tip on the center of the target
board. Then mark the point of weight on the ground.
5. Pivot the edge of the target board 25° to either side.
NOTE:
Approx. 90 mm (3.54 in) shift rates the 25° movement.
NOTE:
The distance between center of laser beam axis and target board is 4 m (13 ft).
6. Do not place anything in the space shown in the figure (view from top).
NOTE:
In case the space shown in the figure is not available, make a space by covering the side of the target
board with a 1400 mm (4.6 ft)-size frosted black board or black cloth.
PKIB8355E
PKIB8356E
PKIB8357E
PKIB8358E
Page 27 of 4647
![INFINITI M35 2007 Factory Service Manual ACS-18
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: 2007 April2007 M35/M45
Aiming AdjustmentNKS004CQ
CAUTION:
Complete all necessary work for laser beam adjustment until the adjustment completes as s INFINITI M35 2007 Factory Service Manual ACS-18
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: 2007 April2007 M35/M45
Aiming AdjustmentNKS004CQ
CAUTION:
Complete all necessary work for laser beam adjustment until the adjustment completes as s](/manual-img/42/57024/w960_57024-26.png)
ACS-18
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: 2007 April2007 M35/M45
Aiming AdjustmentNKS004CQ
CAUTION:
Complete all necessary work for laser beam adjustment until the adjustment completes as shown
in the procedure. If the procedure does not complete, the ICC system is inoperable.
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
1. Connect CONSULT-II and CONSULT-II CONVERTER, and then
touch “ICC” on “SELECT SYSTEM” screen.
If “ICC” is not indicated, go to GI-39, "
CONSULT-II Data Link
Connector (DLC) Circuit" .
2. Touch “WORK SUPPORT”.
3. Touch “LASER BEAM ADJUST”.
4. Touch “START”.
CAUTION:
If the adjustment screen does not appear on the CONSULT-
II screen in 10 seconds. After touching “LASER BEAM
ADJUST” screen, the following causes may be considered:
Target is not set accurately.
There is not enough space beside the target.
The range of laser beam aiming exceeds for improper
installation position.
–Deformation of vehicle body.
–Deformation of unit.
–Deformation of bracket.
The area is not suitable for the adjustment work.
ICC sensor integrated unit is not clean.
BCIA0030E
BCIA0031E
SKIA6191E
PKIB8359E
Page 28 of 4647
![INFINITI M35 2007 Factory Service Manual LASER BEAM AIMING ADJUSTMENT
ACS-19
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
5. After the CONSULT-II displays “ADJUST THE VERTICAL OF
LASER BEAM AIMING” turn the up-down d INFINITI M35 2007 Factory Service Manual LASER BEAM AIMING ADJUSTMENT
ACS-19
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
5. After the CONSULT-II displays “ADJUST THE VERTICAL OF
LASER BEAM AIMING” turn the up-down d](/manual-img/42/57024/w960_57024-27.png)
LASER BEAM AIMING ADJUSTMENT
ACS-19
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
5. After the CONSULT-II displays “ADJUST THE VERTICAL OF
LASER BEAM AIMING” turn the up-down direction adjusting
screw until “U/D CORRECT” value is set in the range of ±4.
CAUTION:
Turn the screw slowly. The value change on display is
slower than actual movement of the ICC sensor integrated
unit. Wait for 2 seconds every time the screw is turned half
a rotation.
NOTE:
Turning the screw clockwise to laser beam is downward and
counterclockwise to laser beam is upward.
6. When “U/D CORRECT” value indicates ±4, confirm that the margin of value remains within ±4 at least for
2 seconds with no equipment or hand touching the ICC sensor integrated unit.
When “COMPLETED THE VERTICAL AIMING OF LASER
BEAM” appears on screen, touch “END”.
CAUTION:
Be sure that the margin of “U/D CORRECT” is within ±4 with
ICC sensor integrated unit is untouched.
7. Confirm that “ADJUSTING AUTOMATIC HORIZONTAL LASER
BEAM AIMING” is on screen and wait for a while (maximum: 10
seconds).
PKIB8360E
PKIB8361E
PKIB8362E
PKIB8363E
Page 29 of 4647
ACS-20
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: 2007 April2007 M35/M45
8. Confirm that “NORMALLY COMPLETED” is displayed on CON-
SULT-II and close the aiming adjustment procedure by touching
“END”.
CAUTION:
Complete all the procedures once “LASER BEAM ADJUST”
mode is entered in CONSULT-II. When the procedure is dis-
continued, the ICC system is inoperable.
CHECK AFTER THE ADJUSTMENT
Test the ICC system operation by ICC system running test. Refer to ACS-12, "ICC System Running Test" .
PKIB8364E
Page 30 of 4647
ELECTRICAL UNITS LOCATION
ACS-21
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
ELECTRICAL UNITS LOCATIONPFP:25230
Component Parts and Harness Connector LocationNKS004CR
PKIB8131E
Page 31 of 4647
ACS-22
[ICC]
WIRING DIAGRAM
Revision: 2007 April2007 M35/M45
WIRING DIAGRAMPFP:00000
SchematicNKS004CS
TKWT3224E
Page 32 of 4647
WIRING DIAGRAM
ACS-23
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
Wiring Diagram — ICC —NKS004CT
TKWT5302E