2007 INFINITI M35 control

ABCDEFGHIJKMLQUICK REFERENCE INDEX AGENERAL INFORMATIONGIGeneral InformationBENGINEEMEngine MechanicalLUEngine Lubrication SystemCOEngine Cooling SystemECEngine Control SystemFLFuel SystemEXExhaust SystemACCAccelerator Control SystemCTRANSMISSION/
TRANSAXLEATAutomatic TransmissionDDRIVELINE/AXLETFTransferPRPropeller ShaftFFDFront Final DriveRFDRear Final DriveFAXFront AxleRAXRear AxleESUSPENSIONFSUFront SuspensionRSURear SuspensionWTRoad Wheels & TiresFBRAKESBRBrake SystemPBParking Brake SystemBRCBrake Control SystemGSTEERINGPSPower Steering SystemSTCSteering Control SystemHRESTRAINTSSBSeat BeltsSRSSupplemental Restraint System
(SRS)IBODYBLBody, Lock & Security SystemGWGlasses, Window System & Mir-
rorsRFRoofEIExterior & InteriorIPInstrument PanelSESeatJAIR CONDITIONERATCAutomatic Air ConditionerKELECTRICALSCStarting & Charging SystemLTLighting SystemDIDriver Information SystemWWWiper, Washer & HornBCSBody Control SystemLANLAN SystemAVAudio-Visual SystemACSAuto Cruise Control SystemPGPower Supply, Ground & Circuit Ele-
mentsLMAINTENANCEMAMaintenanceMINDEXIDXAlphabetical IndexEdition: January 2005
Revision:April 2007

ACC-1
ACCELERATOR CONTROL SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION ACC
A
ACC
Revision: 2007 April2007 M35/M45
ACCELERATOR CONTROL SYSTEM
PRECAUTIONS .......................................................... 2
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 2
ACCELERATOR CONTROL SYSTEM ...................... 3Components ............................................................. 3
Removal and Installation .......................................... 3
REMOVAL ............................................................. 3
INSTALLATION ..................................................... 4
INSPECTION AFTER INSTALLATION .................. 4

ACCELERATOR CONTROL SYSTEM
ACC-3
C
D
E
F
G
H
I
J
K
L
MA
ACC
Revision: 2007 April2007 M35/M45
ACCELERATOR CONTROL SYSTEMPFP:18005
ComponentsNBS005RP
Removal and InstallationNBS005RQ
REMOVAL
1. Disconnect accelerator pedal position sensor harness connector.
2. Remove front kicking plate and dash side finisher. Refer to EI-37, "
BODY SIDE TRIM" .
3. Remove the cap and the inside mounting nut, and then disassemble the accelerator pedal pad from the
floor carpet.
4. Press the pin (1) with long-nose pliers and pull them out in the
direction shown by the arrow ( ). Then remove the accelerator
pedal pad (2).
CAUTION:
Do not disengage the part (the link) other than pins.
5. Remove accelerator pedal stopper cover.
1.Accelerator pedal bracket and lever
assembly2. Accelerator pedal stopper cover 3. Cap
4. Accelerator pedal pad 5. Pin
PBIC3203E
KBIA3594J

ACC-4
ACCELERATOR CONTROL SYSTEM
Revision: 2007 April2007 M35/M45
6. Pull up the floor carpet.
7. Remove mounting nuts of accelerator pedal bracket.
8. Remove accelerator pedal bracket and lever assembly.
CAUTION:

Do not disassemble accelerator lever. Do not remove accelerator pedal position sensor from
accelerator lever.

Avoid impact from dropping etc. during handling.

Be careful to keep accelerator lever away from water.
INSTALLATION
Installation is the reverse order of removal.
INSPECTION AFTER INSTALLATION

Make sure accelerator pedal moves smoothly within the whole operation range when it is fully depressed
and released.

Make sure accelerator pedal securely returns to the fully released position.

For the electrical inspection of accelerator pedal position sensor, refer to the following.
–VQ35DE
EC-617, "
DTC P2122, P2123 APP SENSOR".
–VK45DE
EC-1336, "
DTC P2122, P2123 APP SENSOR".
CAUTION:
When harness connector of accelerator pedal position sensor is disconnected, perform “Acceler-
ator Pedal Released Position Learning”. Refer to EC-86, "
Accelerator Pedal Released Position
Learning" (VQ35DE) or EC-788, "Accelerator Pedal Released Position Learning" (VK45DE).

ACS-1
AUTO CRUISE CONTROL SYSTEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION ACS
A
B
ACS
Revision: 2007 April2007 M35/M45
AUTO CRUISE CONTROL SYSTEM
ASCD
AUTOMATIC SPEED CONTROL DEVICE (ASCD) ..... 3
Description ............................................................... 3
ICC
PRECAUTIONS .......................................................... 4
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 4
Precautions for ICC System Service ........................ 4
PREPARATION ........................................................... 5
Special Service Tools ............................................... 5
DESCRIPTION ............................................................ 6
Outline ...................................................................... 6
VEHICLE-TO-VEHICLE DISTANCE CONTROL
MODE ................................................................... 6
CONVENTIONAL (FIXED SPEED) CRUISE
CONTROL MODE ................................................. 6
BRAKE ASSIST (WITH PREVIEW FUNCTION) ..... 6
Functional Diagram .................................................. 7
Components Description .......................................... 9
CAN Communication ................................................ 9
CAN COMMUNICATION UNIT ............................. 9
Switch Operation .................................................... 10
IN VEHICLE-TO-VEHICLE DISTANCE CON-
TROL MODE ....................................................... 10
IN CONVENTIONAL (FIXED SPEED) CRUISE
CONTROL MODE ............................................... 10
ICC System Display ................................................ 11
IN VEHICLE-TO-VEHICLE DISTANCE CON-
TROL MODE ........................................................ 11
IN CONVENTIONAL (FIXED SPEED) CRUISE
CONTROL MODE ................................................ 11
ACTION TEST .......................................................... 12
ICC System Running Test ...................................... 12
VEHICLE-TO-VEHICLE DISTANCE CONTROL
MODE ................................................................. 12
CONVENTIONAL (FIXED SPEED) CRUISE
CONTROL MODE ............................................... 13LASER BEAM AIMING ADJUSTMENT ................... 15
Outline .................................................................... 15
Preparation ............................................................. 15
Outline of Adjustment Procedure ............................ 15
Setting the ICC Target Board .................................. 15
ADJUSTING HEIGHT OF THE TARGET ............ 15
ADJUSTING THE RIGHT-LEFT POSITION OF
THE TARGET ...................................................... 16
SETTING THE TARGET ..................................... 16
Aiming Adjustment .................................................. 18
CHECK AFTER THE ADJUSTMENT .................. 20
ELECTRICAL UNITS LOCATION ............................ 21
Component Parts and Harness Connector Location ... 21
WIRING DIAGRAM ................................................... 22
Schematic ............................................................... 22
Wiring Diagram — ICC — ...................................... 23
TERMINALS AND REFERENCE VALUE ................. 28
Terminals and Reference Value for ICC Sensor Inte-
grated Unit .............................................................. 28
TROUBLE DIAGNOSIS - GENERAL DESCRIP-
TION .......................................................................... 29
Fail-Safe Function .................................................. 29
Work Flow ............................................................... 29
CONSULT-II Function (ICC) ................................... 30
DESCRIPTION .................................................... 30
CONSULT-II BASIC OPERATION ....................... 30
WORK SUPPORT ............................................... 30
SELF-DIAGNOSTIC RESULTS ........................... 31
DATA MONITOR ................................................. 31
ACTIVE TEST ..................................................... 33
Self-Diagnostic Function ......................................... 34
WITH CONSULT-II .............................................. 34
WITHOUT CONSULT-II ....................................... 35
SELF-DIAGNOSIS BY DOT MATRIX LCD WILL
NOT RUN ............................................................ 36
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC
ITEMS ........................................................................ 40
Diagnostic Trouble Code (DTC) Chart ................... 40
DTC 0 CONTROL UNIT ......................................... 42
DTC 1 POWER SUPPLY CIR, DTC 2 POWER SUP-

ACS-2Revision: 2007 April2007 M35/M45 PLY CIR 2 ............................................................... 42
DTC 3 VHCL SPEED SE CIRC .............................. 43
DTC 4 ABS/TCS/VDC CIRC .................................. 43
DTC 5 BRAKE SW/STOP L SW ............................. 44
DTC 6 OPERATION SW CIRC ............................... 48
DTC 12 LASER BEAM OFFCNTR ......................... 49
DTC 13 STOP LAMP RLY FIX ............................... 50
DTC 14 ECM CIRCUIT ........................................... 56
DTC 15 GEAR POSITION ...................................... 57
DTC 16 RADAR STAIN .......................................... 58
DTC 18 LASER AIMING INCMP ............................ 58
DTC 21 UNIT HIGH TEMP ..................................... 58
DTC 24 NP RANGE ............................................... 59
DTC 25 SHIFT RANGE IND ................................... 59
DTC 26 ECD MODE MALF .................................... 60
DTC 27 ECD PWR SUPLY CIR .............................. 60
DTC 100 CAN COMM CIRCUIT ............................. 61
DTC 110 CONTROL UNIT (CAN) ........................... 61
TROUBLE DIAGNOSIS FOR SYMPTOMS .............. 62
Symptom Chart ....................................................... 62
Symptom 1: MAIN Switch Does Not Turn ON*
1 ,
MAIN Switch Does Not Turn OFF*
2 ........................ 63Symptom 2: ICC System Cannot Be Set (MAIN
Switch Turns ON/OFF) ............................................ 64
Symptom 3: ICC System Cannot Be Operated by
CANCEL Switch, RESUME/ACCELERATE Switch
or DISTANCE Switch .............................................. 65
Symptom 4: ICC System Is Not Cancelled When
the A/T Selector Lever Is In Other Than “D” and “M” ... 65
Symptom 5: Chime Does Not Sound ...................... 66
Symptom 6: Driving Force Is Hunting ..................... 67
Symptom 7: ICC System Frequently Cannot Detect
the Vehicle Ahead/ Detection Zone Is Short ........... 67
Symptom 8: The System Does Not Detect the Vehi-
cle Ahead at All ....................................................... 68
ELECTRICAL COMPONENT INSPECTION ............. 69
ICC Steering Switch ................................................ 69
ICC Brake Hold Relay ............................................. 69
ICC Brake Switch and Stop Lamp Switch ............... 69
REMOVAL AND INSTALLATION .............................. 70
ICC Sensor Integrated Unit ..................................... 70
REMOVAL ............................................................ 70
INSTALLATION .................................................... 70
ICC Steering Switch ................................................ 70

AUTOMATIC SPEED CONTROL DEVICE (ASCD)
ACS-3
[ASCD]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
[ASCD]AUTOMATIC SPEED CONTROL DEVICE (ASCD)PFP:18930
DescriptionNKS004CB
Regarding the information for ASCD system, refer to EC-36, "AUTOMATIC SPEED CONTROL DEVICE
(ASCD)" (VQ35DE), EC-738, "AUTOMATIC SPEED CONTROL DEVICE (ASCD)" (VK45DE).

ACS-6
[ICC]
DESCRIPTION
Revision: 2007 April2007 M35/M45
DESCRIPTIONPFP:00000
OutlineNKS004CF
The Intelligent Cruise Control (ICC) system automatically maintains a selected distance from the vehicle
ahead according to that vehicle's speed, or at the set speed, if the road ahead is clear.
The ICC function has two cruise control modes and brake assist (with preview function).
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE
Vehicle-to-vehicle distance control mode, the driver can maintain the same speed as other vehicles without
the constant need to adjust the set speed as the driver would with a normal cruise control system.
The system is intended to enhance the operation of the vehicle when following the vehicle traveling in the
same lane and direction.
If the ICC sensor integrated unit detects a slower moving vehicle ahead, the system will reduce speed so that
the vehicle ahead can be followed at the selected distance.
The system automatically controls the throttle and applies the brakes (up to 25% of vehicle braking power) if
necessary.
The detection range of the sensor is approximately 390 ft (120 m) ahead.
Refer to Owner's Manual for Intelligent Cruise Control System operating instructions.
CONVENTIONAL (FIXED SPEED) CRUISE CONTROL MODE
Conventional (fixed speed) cruise control mode is cruising at preset speeds.
Refer to Owner's Manual for Intelligent Cruise Control System operating instructions.
BRAKE ASSIST (WITH PREVIEW FUNCTION)
When the force applied to brake pedal exceeds a certain level, the Brake Assist is activated and generates a
greater braking force than that of a conventional brake booster even with light pedal force.
When the Preview Function identifies the need to apply the sudden brake by sensing the vehicle ahead in the
same lane and the distance and relative speed from it, it applies the brake pre-pressure before driver
depresses the brake pedal and improves brake response by reducing its free play.
Refer to Owner's Manual for BRAKE ASSIST (WITH PREVIEW FUNCTION) operating instructions.