2007 INFINITI M35 warning

ACC-2
PRECAUTIONS
Revision: 2007 April2007 M35/M45
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NBS005RO
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.

ACS-4
[ICC]
PRECAUTIONS
Revision: 2007 April2007 M35/M45
[ICC]PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NKS004CC
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for ICC System ServiceNKS004CD

Do not look straight into the laser beam discharger when adjusting laser beam aiming.

Turn the MAIN switch OFF in conditions similar to driving, such as free rollers or a chassis dynamometer.

Do not use the ICC sensor integrated unit removing from vehicle. Never disassemble and remodel.

Erase DTC when replacing parts of ICC system, then check the operation of ICC system after adjusting
laser beam aiming if necessary.

ACS-8
[ICC]
DESCRIPTION
Revision: 2007 April2007 M35/M45

Items of output signal to be checked with “DATA MONITOR”.

Items of output signal to be checked with “ACTIVE TEST”.
Shift position signal×
TCMD RANGE SW
[ON/OFF]ICC sensor integrated unit receives shift position signal from
TCM with CAN communication.
×NP RANGE SW
[ON/OFF]ICC sensor integrated unit receives shift position signal from
TCM with CAN communication.
Output shaft revo-
lution signal×VHCL SPD AT
[km/h] or [mph]ICC sensor integrated unit receives A/T vehicle speed sen-
sor signal (output shaft revolution signal) from TCM with
CAN communication.
Current gear posi-
tion signal×GEAR
[1, 2, 3, 4, 5]ICC sensor integrated unit receives current gear position sig-
nal from TCM with CAN communication.
Vehicle speed sig-
nal×ABS actuator and
electric unit (con-
trol unit)VHCL SPEED SE
[km/h] or [mph]ICC sensor integrated unit receives vehicle speed signal
(wheel speed) from ABS actuator and electric unit (control
unit) with CAN communication.
Front wiper request
signal×BCMWIPER SW
[OFF/LOW/HIGH]ICC sensor integrated unit receives front wiper request signal
from BCM with CAN communication. Signal name CAN Transmission unitMonitored Item
[unit]Description
Signal name CAN Reception unitMonitored Item
[unit]Description
Meter display signal×
Combination
meter
(through unified
meter and A/C
amp.)CRUISE LAMP
[ON/OFF]
ICC sensor integrated unit transmits meter display signal to
combination meter (through unified meter and A/C amp.)
with CAN communication. ×OWN VHCL
[ON/OFF]
×VHCL AHEAD
[ON/OFF]
×SET DISP IND
[ON/OFF]
ICC system warning
lamp signal×ICC WARNING
[ON/OFF]ICC sensor integrated unit transmits ICC system warning
lamp signal to combination meter (through unified meter and
A/C amp.) with CAN communication.
Buzzer output signal×BUZZER O/P
[ON/OFF] ICC sensor integrated unit transmits buzzer output signal to
combination meter (through unified meter and A/C amp.)
with CAN communication.
ICC brake hold relay
drive signalICC brake hold
relaySTP LMP DRIVE
[ON/OFF]ICC sensor integrated unit outputs stop lamp drive output
signal to ICC brake hold relay.
Signal name CAN Reception unit Test Item Description
Buzzer output signal×Combination
meter
(through unified
meter and A/C
amp.)ICC BUZZERAble to beep the ICC warning chime with a driving signal
from ICC sensor integrated unit.

Meter display signal

ICC system warn-
ing lamp signal×METER LAMPAble to illuminate the ICC system warning lamp and the
MAIN switch indicator lamp with a driving signal from the
ICC sensor integrated unit.
ICC brake hold relay
drive signalICC brake hold
relaySTOP LAMPAble to turn ON the ICC brake hold relay with a driving sig-
nal from the ICC sensor integrated unit.

DESCRIPTION
ACS-9
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
Components DescriptionNKS004CH
CAN CommunicationNKS004CI
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tric control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN COMMUNICATION UNIT
Refer to LAN-52, "CAN Communication Signal Chart" .
ComponentVehicle-to-
vehicle
distance
control modeConventional
(fixed speed)
cruise
control modeBrake assist
(with pre-
view func-
tion)Description
ICC sensor integrated unit×××

Controls vehicle distance by operating electric throttle
control actuator based on that sensor signals and
CAN communication data.

Controls vehicle distance by transmitting deceleration
degree commandment value signal to ABS actuator
and electric unit (control unit) when deceleration with
brake is needed.

Irradiates laser beam, and receives reflected laser
beam to measure distance from preceding vehicle.
ECM×××Transmits accelerator pedal position signal, ICC brake
switch signal, stop lamp switch signal and ICC steering
switch signal to ICC sensor integrated unit through CAN
communication.
ABS actuator and electric
unit (control unit)×××

Transmits vehicle speed signal (wheel speed) and
stop lamp switch signal to ICC sensor integrated unit
through CAN communication.

Receives deceleration degree commandment value
signal from ICC sensor integrated unit, and controls
brake fluid pressure with the ABS motor.
BCM×Transmits front wiper request signal to ICC sensor inte-
grated unit through CAN communication.
TCM××Transmits gear position signal and output shaft revolu-
tion signal to ICC sensor integrated unit through CAN
communication.
Unified meter and A/C amp.×××Receives meter display signal, ICC warning lamp signal
and buzzer output signal from ICC sensor integrated
unit through CAN communication.
ICC brake switch×××Transmits operating signal to ECM when depressing
brake pedal. ICC sensor integrated unit cancels cruise
system at driver's brake operation.
Stop lamp switch×××Transmits operating signal to ECM and ABS actuator
and electric unit (control unit) when depressing brake
pedal. ICC sensor integrated unit cancels cruise system
at driver's brake operation.

DESCRIPTION
ACS-11
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
ICC System DisplayNKS004CK
The status of ICC system is displayed by dot matrix LCD, MAIN switch indicator lamp and ICC system warning
lamp on the combination meter.
IN VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE
IN CONVENTIONAL (FIXED SPEED) CRUISE CONTROL
MODE
PKIB8347E
No. Display items Description
1 Set vehicle speed indicator Indicates the set vehicle speed.
2 Vehicle ahead detection indicator Indicates whether it detects a vehicle ahead.
3 Set distance indicatorIndicates the selected distance between vehicles set with the DISTANCE
switch.
4 Own vehicle indicator Indicates the base vehicle.
5 MAIN switch indicator lamp (Green) Indicates that the MAIN switch is ON.
6Intelligent cruise control system warning
lamp (Orange)The light comes on if there is a malfunction in the ICC system.
PKIB4982J
No. Display items Description
1 Set switch indicatorIndicates that the set conventional (fixed speed) cruise control mode is con-
trolled.
2 MAIN switch indicator lamp (Green) Indicates that the MAIN switch is ON.
3Intelligent cruise control system warning
lamp (Orange)The light comes on if there is a malfunction in the ICC system.

TROUBLE DIAGNOSIS - GENERAL DESCRIPTION
ACS-29
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
TROUBLE DIAGNOSIS - GENERAL DESCRIPTIONPFP:00000
Fail-Safe FunctionNKS004CV
When a malfunction occurs in ICC system, a chime sounds a beep, the system is released and ICC system
warning lamp in combination meter illuminates. System setting is not accepted when malfunction is detected.
Work FlowNKS004CW

Reference 1··· Refer to ACS-34, "Self-Diagnostic Function" .

Reference 2··· Refer to ACS-40, "Diagnostic Trouble Code (DTC) Chart" .

Reference 3··· Refer to ACS-62, "Symptom Chart" .

Reference 4··· Refer to GI-39, "CONSULT-II Data Link Connector (DLC) Circuit" /ACS-36, "SELF-DIAG-
NOSIS BY DOT MATRIX LCD WILL NOT RUN" .
SKIA1227E

ACS-32
[ICC]
TROUBLE DIAGNOSIS - GENERAL DESCRIPTION
Revision: 2007 April2007 M35/M45
THRTL SENSOR
[deg]××NOTE:
This item is displayed, but cannot monitor.
SET DISTANCE
[SHOR/MID/LONG]××Indicates set distance memorized in ICC sensor integrated unit.
MAIN SW
[ON/OFF]××Indicates [ON/OFF] status as judged from ICC steering switch signal (ECM
transmits ICC steering switch signal through CAN communication).
SET/COAST SW
[ON/OFF]××Indicates [ON/OFF] status as judged from ICC steering switch signal (ECM
transmits ICC steering switch signal through CAN communication).
CANCEL SW
[ON/OFF]××Indicates [ON/OFF] status as judged from ICC steering switch signal (ECM
transmits ICC steering switch signal through CAN communication).
RESUME/ACC SW
[ON/OFF]××Indicates [ON/OFF] status as judged from ICC steering switch signal (ECM
transmits ICC steering switch signal through CAN communication).
DISTANCE SW
[ON/OFF]×Indicates [ON/OFF] status as judged from ICC steering switch signal (ECM
transmits ICC steering switch signal through CAN communication).
CRUISE OPE
[ON/OFF]××Indicates whether controlling or not (ON means “controlling”).
BRAKE SW
[ON/OFF]××Indicates [ON/OFF] status as judged from ICC brake switch signal (ECM
transmits ICC brake switch signal through CAN communication).
STOP LAMP SW
[ON/OFF]××Indicates [ON/OFF] status as judged from stop lamp switch signal (ECM
transmits stop lamp switch signal through CAN communication).
CRUISE LAMP
[ON/OFF]××Indicates [ON/OFF] status of MAIN switch indicator lamp output.
CLUTCH SW SIG
[ON/OFF]××NOTE:
This item is displayed, but cannot monitor.
NP SW SIG
[ON/OFF]××NOTE:
This item is displayed, but cannot monitor.
STP LMP DRIVE
[ON/OFF]××Indicates [ON/OFF] status of ICC brake hold relay drive output.
PWR SUP MONI
[V]××Indicates IGN voltage input by ICC sensor integrated unit.
IDLE SW
[ON/OFF]×Indicates [ON/OFF] status of idle switch read from ICC sensor integrated
unit through CAN communication (ECM transmits ON/OFF status through
CAN communication).
OWN VHCL
[ON/OFF]×Indicates [ON/OFF] status of own vehicle indicator output.
VHCL AHEAD
[ON/OFF]×Indicates [ON/OFF] status of vehicle ahead detection indicator output.
ICC WARNING
[ON/OFF]×Indicates [ON/OFF] status of ICC system warning lamp output.
BUZZER O/P
[ON/OFF] ×Indicates [ON/OFF] status of ICC warning chime output.
ENGINE RPM
[rpm]×Indicates engine speed read from ICC sensor integrated unit through CAN
communication (ECM transmits engine speed through CAN communica-
tion).
WIPER SW
[OFF/LOW/HIGH]×Indicates wiper [OFF/LOW/HIGH] status (BCM transmits front wiper request
signal through CAN communication).
YAW R AT E
[deg/s]×NOTE:
This item is displayed, but cannot monitor.
D RANGE SW
[ON/OFF]
×Indicates [ON/OFF] status of “D” and “M” positions read from ICC sensor
integrated unit through CAN communication; ON when position “D” and “M”
(TCM transmits A/T position indicator lamp signal through CAN communi-
cation). Monitored Item [unit]MAIN
SIGNALSSELEC-
TION FROM
MENUDescription

TROUBLE DIAGNOSIS - GENERAL DESCRIPTION
ACS-33
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
ACTIVE TEST
CAUTION:

Never perform the active test while driving.

“ACTIVE TEST” cannot be started while ICC system warning lamp illuminates.
1. Touch “ACTIVE TEST” on “SELECT DIAG MODE” screen.
2. Touch any of “ICC BUZZER”, “METER LAMP” and “STOP
LAMP” on selection screen.
3. Touch necessary item and “START”.
4. “ACTIVE TEST” screen will be shown.
ICC BUZZER
Touch “TEST START” and “RESET” in “MODE2” to check if ICC
warning chime operates as in the following chart.
NP RANGE SW
[ON/OFF]×Indicates A/T position indicator lamp signal read from ICC sensor integrated
unit through CAN communication (TCM transmits A/T position indicator
lamp signal through CAN communication).
VHCL SPD AT
[km/h] or [mph]×Indicates vehicle speed calculated from A/T vehicle speed sensor read from
ICC sensor integrated unit through CAN communication (TCM transmits A/
T vehicle speed sensor signal through CAN communication).
GEAR
[1, 2, 3, 4, 5]×Indicates A/T gear position read from ICC sensor integrated unit through
CAN communication (TCM transmits current gear position signal through
CAN communication).
MODE SIG
[OFF, ICC, ASCD]×Indicates the active mode from ICC or ASCD (conventional (fixed speed)
cruise control mode).
SET DISP IND
[ON/OFF]×Indicates [ON/OFF] status of SET switch indicator output.
DISTANCE
[m]×Indicates the distance from the vehicle ahead.
RELATIVE SPD
[m/s]×Indicates the relative speed of the vehicle ahead. Monitored Item [unit]MAIN
SIGNALSSELEC-
TION FROM
MENUDescription
PKIB8366E
BUZZER O/P ON OFF
Buzzer sound Beep Not activated
PKIB8368E