Page 3361 of 3371

WW-48
REAR WIPER AND WASHER SYSTEM
Revision: August 20072004 QX56
3. CHECK REAR WIPER MOTOR AUTO STOP SWITCH GROUNDS
Check continuity between rear wiper motor harness connector D704
terminals and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair harness or connector.
4. CHECK REAR WIPER OPERATING
1. Connect BCM connectors and rear wiper motor connector.
2. Turn ignition switch ON.
3. Turn rear wiper switch ON, then to OFF when wiper arm
reaches mid sweep.
4. Check voltage between rear wiper motor connector D704 termi-
nal 6 (Y) and ground.
OK or NG
OK >> Replace rear wiper motor. Refer to WW-51, "Removal
and Installation of Rear Wiper Motor" .
NG >> Replace BCM. Refer to BCS-19, "
Removal and Installation of BCM" .
Only Rear Wiper Does Not OperateEKS007FX
1. CHECK COMBINATION SWITCH INPUT SIGNAL
Select “BCM” on CONSULT-II. With “WIPER” data monitor, make
sure “RR WIPER ON” turns ON-OFF according to operation of wiper
switch.
OK or NG
OK >> Replace BCM. Refer to BCS-19, "Removal and Installa-
tion of BCM" .
NG >> Check the wiper switch. Refer to BCS-3, "
COMBINA-
TION SWITCH READING FUNCTION" .
Rear wiper motor
Continuity
ConnectorTe r m i n a l
(wire color)
D7041 (Y/L)
GroundNo
2 (O)
3 (B)
Ye s
5 (B)
WKIA2097E
Battery voltage should exist on the reverse wipe
until arm is seated in the stop.
WKIA2098E
When rear wiper switch is in
ON position: RR WIPER ON ON
SKIA4248E
Page 3362 of 3371

REAR WIPER AND WASHER SYSTEM
WW-49
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: August 20072004 QX56
Only Rear Wiper Intermittent Does Not OperateEKS007FY
1. CHECK COMBINATION SWITCH INPUT SIGNAL
Select “BCM” on CONSULT-II. With “WIPER” data monitor, make
sure “RR WIPER INT” turns ON-OFF according to operation of wiper
switch.
OK or NG
OK >> Replace BCM. Refer to BCS-19, "Removal and Installa-
tion of BCM" .
NG >> Check the wiper switch. Refer to BCS-3, "
COMBINA-
TION SWITCH READING FUNCTION" .
Wiper Does Not Wipe When Rear Washer OperatesEKS007FZ
1. CHECK COMBINATION SWITCH INPUT SIGNAL
Select “BCM” on CONSULT-II. With “WIPER” data monitor, make
sure “RR WASHER SW” turns ON-OFF according to operation of
rear washer switch.
OK or NG
OK >> Replace BCM. Refer to BCS-19, "Removal and Installa-
tion of BCM" .
NG >> Check the wiper switch. Refer to BCS-3, "
COMBINA-
TION SWITCH READING FUNCTION" . When rear wiper switch is in
INT position: RR WIPER INT ON
SKIA4249E
When rear wiper switch is in
WASHER position: RR WASHER SW ON
SKIA4250E
Page 3363 of 3371
WW-50
REAR WIPER AND WASHER SYSTEM
Revision: August 20072004 QX56
Removal and Installation of Rear Wiper Arm, Adjustment of Rear Wiper Arm
Stop Location
EKS007G0
REMOVAL
1. Operate the rear wiper motor and stop it at the auto stop position.
2. Remove rear wiper arm cover by gripping bottom edge and
rotating cover up. Remove mounting nut, and remove the wiper
arm.
INSTALLATION
1. Prior to wiper arm installation, turn on wiper switch to operate wiper motor and then turn it “OFF” (Auto
Stop).
2. Clean up the pivot area as illustrated. This will reduce the possi-
bility of wiper arm looseness.
3. Install rear wiper arm so that the arm rests in the stopper, then
tighten wiper arm nut to specification.
LKIA0608E
Rear wiper arm nut : 11.2 N·m
(1.1 kg-m, 8 ft-lb)
SEL024J
Page 3364 of 3371
REAR WIPER AND WASHER SYSTEM
WW-51
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: August 20072004 QX56
Removal and Installation of Rear Wiper Motor EKS007G1
REMOVAL
1. Remove rear wiper arm. Refer to WW-50, "Removal and Instal-
lation of Rear Wiper Arm, Adjustment of Rear Wiper Arm Stop
Location" .
2. Remove pivot cap.
3. Remove back door finisher lower. Refer to EI-41, "
BACK DOOR
TRIM" .
4. Remove the hatch glass latch. Refer to BL-136, "
BACK DOOR
LOCK" .
5. Disconnect rear wiper motor connector.
6. Remove rear wiper motor mounting bolts, and remove rear
wiper motor.
INSTALLATION
CAUTION:
Do not drop the wiper motor or cause it to contact other parts.
WKIA3425E
1. Wiper arm cover 2. Wiper arm and blade 3. Pivot cap
4. Rear wiper motor 5. Wiper arm stop 6. Rear wiper arm mounting nut
LKIA0416E
Page 3365 of 3371

WW-52
REAR WIPER AND WASHER SYSTEM
Revision: August 20072004 QX56
1. Clean up the pivot area as illustrated. This will reduce possibility
of wiper arm looseness.
2. Install rear wiper motor to the vehicle.
3. Connect rear wiper motor connector.
4. Install hatch glass latch and adjust as necessary. Refer to BL-
136, "BACK DOOR LOCK" .
5. Install back door finisher lower. Refer to EI-41, "
BACK DOOR
TRIM" .
6. Attach pivot cap.
7. Attach wiper arm. Refer to WW-50, "
Removal and Installation of
Rear Wiper Arm, Adjustment of Rear Wiper Arm Stop Location"
.
Rear Washer Nozzle AdjustmentEKS007G2
This vehicle is equipped with a non-adjustable rear washer nozzle.
If not satisfied with washer fluid spray coverage, confirm that the washer nozzle is installed correctly.
If the washer nozzle is installed correctly, and the washer fluid spray coverage is not satisfactory, replace
the washer nozzle.
Rear Washer Tube LayoutEKS007G3
Removal and Installation of Rear Washer NozzleEKS007G4
REMOVAL
1. Remove the rear spoiler. Refer to EI-26, "REAR SPOILER" .
2. Remove rear washer tube from nozzle.
3. Release retaining clips, and remove washer nozzle.
INSTALLATION
Installation is in the reverse order of removal.
SEL024J
WKIA1925E
LKIA0418E
Page 3366 of 3371
REAR WIPER AND WASHER SYSTEM
WW-53
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: August 20072004 QX56
Check ValveEKS007G5
A check valve is provided in the washer fluid line. Be careful not
to connect check valve to washer tube in the wrong direction.
Removal and Installation of Rear Wiper and Washer SwitchEKS007G6
Refer to WW-31, "Removal and Installation of Wiper and Washer Switch" .
Removal and Installation of Washer TankEKS007G7
Refer to WW-31, "Removal and Installation of Washer Tank" .
Removal and Installation of Washer MotorEKS007G8
Refer to WW-32, "Removal and Installation of Washer Motor" .
PKIA2546E
Page 3367 of 3371
WW-54
POWER SOCKET
Revision: August 20072004 QX56
POWER SOCKETPFP:253A2
Wiring Diagram — P/SCKT — EKS007G9
WKWA2182E
Page 3368 of 3371
POWER SOCKET
WW-55
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: August 20072004 QX56
Removal and Installation of Power SocketsEKS007GA
REMOVAL
NOTE:
Removal and Installation is common for all power sockets.
1. Remove inner socket from the ring, while pressing the hook on
the ring out from square hole.
2. Disconnect power socket connector.
3. Remove ring from power socket finisher while pressing pawls.
INSTALLATION
Installation is in the reverse order of removal.
WKIA1035E