Page 617 of 3371

AV-30
AUDIO
Revision: August 20072004 QX56
FOR CD ONLY
Noise InspectionEKS007KK
The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunctioning.
Check if noise is caused and/or changed by engine speed, ignition switch turned to each position, and opera-
tion of each piece of electrical equipment, and determine the cause.
NOTE:
The source of the noise can be found easily by listening to the noise while removing the fuses of electrical
components, one by one.
TYPE OF NOISE AND POSSIBLE CAUSE
Power Supply Circuit InspectionEKS007KL
1. CHECK FUSES
Check that the following fuses are not blown.
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of problem before installing new fuse. Refer to PG-4,
"POWER SUPPLY ROUTING CIRCUIT" .
Symptom Possible cause
CD cannot be inserted.
CD
Audio unit CD cannot be ejected.
The CD cannot be played.
The sound skips, stops suddenly, or is distorted.
Occurrence condition Possible cause
Occurs only when engine is ON.A continuous growling noise occurs. The speed of
the noise varies with changes in the engine speed.
Ignition components
A whistling noise occurs while the engine speed is
high. A booming noise occurs while the engine is
running and the lighting switch is ON.
Generator
The occurrence of the noise is linked with the operation of the fuel pump.
Fuel pump condenser
Noise only occurs when various
electrical components are oper-
ating.A cracking or snapping sound occurs with the
operation of various switches.
Relay malfunction, audio unit malfunction
The noise occurs when various motors are operat-
ing.
Motor case ground
Motor
The noise occurs constantly, not just under certain conditions.
Rear defogger coil malfunction
Open circuit in printed heater
Poor ground of antenna amplifier or
antenna feeder line
A cracking or snapping sound occurs while the vehicle is being driven, especially
when it is vibrating excessively.
Ground wire of body parts
Ground due to improper part installation
Wiring connections or a short circuit
Unit Terminals Signal name Fuse No.
Audio unit6 Battery power 31
10 Ignition switch ACC or ON 4
AV s w i t c h1 Battery power 31
2 Ignition switch ACC or ON 4
BOSE speaker amp. 1 Battery power 31
Subwoofer 6 Battery power 17
Page 618 of 3371

AUDIO
AV-31
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: August 20072004 QX56
2. POWER SUPPLY CIRCUIT CHECK
1. Disconnect audio unit, subwoofer or BOSE speaker amp. connector.
2. Check voltage between the audio unit and ground.
3. Check voltage between subwoofer and ground.
4. Check voltage between BOSE speaker amp. and ground.
OK or NG
OK >> GO TO 3.
NG >>
Check connector housings for disconnected or loose
terminals.
Repair harness or connector.
3. GROUND CIRCUIT CHECK
Check continuity between subwoofer harness connector B72 termi-
nal 5 (B) and BOSE speaker amp. harness connector M112 terminal
17 (B) and ground.
OK or NG
OK >> Inspection End.
NG >>
Check connector housings for disconnected or loose
terminals.
Repair harness or connector.
UnitTerminal No.
OFF ACC ON (+)
(-)
ConnectorTerminal
(wire color)
Audio unit M436 (Y) GroundBattery
voltageBattery
voltageBattery
voltage
10 (V) Ground 0 VBattery
voltageBattery
voltage
SKIA1992E
UnitTerminal No.
OFF ACC ON (+)
(-)
ConnectorTerminal
(wire color)
Sub-
wooferB72 6 (R) GroundBattery
voltageBattery
voltageBattery
voltage
WKIA1598E
UnitTerminal No.
OFF ACC ON (+)
(-)
ConnectorTerminal
(wire color)
BOSE
speaker
amp.M112 1 (Y) GroundBattery
voltageBattery
voltageBattery
voltage
SKIA4 311 E
Continuity should exist.
WKIA1599E
Page 619 of 3371

AV-32
AUDIO
Revision: August 20072004 QX56
Steering Switch CheckEKS007KM
1. AV SWITCH SELF-DIAGNOSIS FUNCTION CHECK
1. Start AV switch self-diagnosis function. Refer to AV- 2 7 , "
AV Switch Self-Diagnosis Function" .
2. Operate steering switch.
Does steering switch operate normally?
YES >> Inspection End.
NO >> GO TO 2.
2. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect AV switch connector and spiral cable connector.
3. Check continuity between spiral cable harness connector terminal and AV switch harness connector ter-
minal.
4. Check continuity between AV switch and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness.
3. SPIRAL CABLE CHECK
1. Disconnect spiral cable connector.
2. Check continuity between spiral cable terminals.
OK or NG
OK >> GO TO 4.
NG >> Replace spiral cable. Refer to SRS-47, "
Removal and Installation" .
Te r m i n a l s
Continuity Spiral cable AV switch
Connector Terminal Connector Terminal (Wire color)
M3032 (G)
M9813 (G)
Ye s 31 (L) 14 (L)
24 (R) 12 (R)
Te r m i n a l s
Continuity AV s w i t c h
—
Connector Terminal (Wire color)
M9812 (R)
Ground No 13 (G)
14 (L)
WKIA1600E
Terminals
Continuity Spiral cable
Terminal Terminal
32 16
Ye s 31 17
24 20
WKIA3489E
Page 620 of 3371

AUDIO
AV-33
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: August 20072004 QX56
4. CHECK STEERING SWITCH RESISTANCE
Check resistance between steering switch terminals.
OK or NG
OK >> Inspection End.
NG >> Replace steering switch. Refer to AV- 4 7 , "
Removal and Installation of Steering Wheel Audio Con-
trol Switches" .
AV Switch CheckEKS007KN
1. AV SWITCH SELF-DIAGNOSIS FUNCTION CHECK
1. Perform AV switch self-diagnosis function. Refer to AV- 2 7 , "
AV Switch Self-Diagnosis Function" .
Does AV switch operate normally?
YES >> Inspection End.
NO >> GO TO 2.
2. CHECK AV SWITCH POWER SUPPLY AND GROUND CIRCUIT
1. Check AV switch power supply and ground circuit. Refer to AV-120, "
Power Supply and Ground Circuit
Check for AV Switch" .
OK or NG
YES >> Replace AV switch. Refer to AV-45, "Removal and Installation for AV Switch" .
NO >> Repair malfunctioning part.
Audio Communication Line CheckEKS007KO
1. CHECK AUDIO COMMUNICATION LINE
Start audio communication line check. Refer to AV-126, "Audio Communication Line Check (Between Dis-
play Control Unit and Audio Unit)" .
OK or NG
OK >> Inspection End.
NG >> Replace malfunctioning part.
Terminal Signal name ConditionResistance
(Ω)
(Approx.)
16 17Seek (down) Depress (station) down switch. 165
Power Depress power switch. 0
Volume (down) Depress volume down switch. 652
20 17Seek (up) Depress (station) up switch. 165
Mode Depress mode switch. 0
Volume (up) Depress volume up switch. 652
WKIA3490E
Page 621 of 3371
AV-34
AUDIO
Revision: August 20072004 QX56
Sound Is Not Heard From Front Door Speaker or Front TweeterEKS007KR
1. HARNESS CHECK
1. Disconnect BOSE speaker amp. connector M113 and suspect speaker connector.
2. Check continuity between BOSE speaker amp. harness connec-
tor terminal M113 and suspect speaker harness connector ter-
minal.
3. Check continuity between BOSE speaker amp. harness connec-
tor terminal M113 and ground.
OK or NG
OK >> GO TO 2.
NG >>
Check connector housings for disconnected or loose terminals.
Repair harness or connector.
Terminals
Continuity BOSE speaker amp. Speaker or tweeter
ConnectorTe r m i n a l
(Wire color)ConnectorTerminal
(Wire color)
M11313 (L/W)
D12+ (L/W)
Ye s 14 (L/R) - (L/R)
15 (W/B)
D112+ (W/B)
16 (L/B) - (L/B)
13 (L/W)
M109+ (L/W)
14 (L/R) - (L/R)
15 (W/B)
M 111+ (W/B)
16 (L/B) - (L/B)
Te r m i n a l s
Continuity BOSE speaker amp.
—
Connector Terminal (Wire color)
M11313 (L/W)
Ground No 14 (L/R)
15 (W/B)
16 (L/B)
WKIA2018E
Page 622 of 3371
AUDIO
AV-35
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: August 20072004 QX56
2. FRONT SPEAKER SIGNAL CHECK
1. Connect BOSE speaker amp. connector M113 and suspect speaker connector.
2. Turn ignition switch to ACC.
3. Push “POWER” switch.
4. Check the signal BOSE speaker amp. harness connector M113
terminal with CONSULT-II or oscilloscope.
OK or NG
OK >> Replace suspect speaker. Refer to AV- 4 5 , "Removal
and Installation of Front Door Speaker" or AV- 4 6 ,
"Removal and Installation of Front Tweeter" .
NG >> GO TO 3.
Te r m i n a l s
Condi-
tionReference
signal (+) (-)
Con-
nectorTe r m i n a l
(Wire
color)Con-
nectorTe r m i -
nal
(Wire
color)
M11313 (L/W)
M11314 (L/R)
Receive
audio
signal 15 (W/B) 16 (L/B)
SKIA4283E
SKIA0177E
Page 623 of 3371
AV-36
AUDIO
Revision: August 20072004 QX56
3. HARNESS CHECK
1. Disconnect audio unit connector and BOSE speaker amp. connector.
2. Check continuity between audio unit harness connector terminal
and BOSE speaker amp. harness connector terminal.
3. Check continuity between audio unit harness connector terminal
and ground.
OK or NG
OK >> GO TO 4.
NG >>
Check connector housings for disconnected or loose terminals.
Repair harness or connector.
Te r m i n a l s
Continuity Audio unit BOSE speaker amp.
ConnectorTe r m i n a l
(Wire color)ConnectorTe r m i n a l
(Wire color)
M431 (B)
M11329 (B)
Ye s 2 (W) 30 (W)
3 (BR) 27 (BR)
4 (Y) 28 (Y)
Te r m i n a l s
Continuity Audio unit
—
Connector Terminal (Wire color)
M431 (B)
Ground No 2 (W)
3 (BR)
4 (Y)
SKIA4284E
Page 624 of 3371
AUDIO
AV-37
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: August 20072004 QX56
4. FRONT SPEAKER SIGNAL CHECK
1. Connect audio unit connector and BOSE speaker amp. connector.
2. Turn ignition switch ACC.
3. Push “POWER” switch.
4. Check the signal audio unit harness connector terminal with
CONSULT-II or oscilloscope.
OK or NG
OK >> Replace BOSE speaker amp. Refer to AV- 4 6 , "Removal
and Installation of BOSE Speaker Amp." .
NG >> Replace audio unit. Refer to AV- 4 5 , "
Removal and
Installation for Audio Unit" .
Te r m i n a l s
Condi-
tionReference
signal (+) (-)
Con-
nectorTe r m i -
nal
(Wire
color)Con-
nectorTe r m i -
nal
(Wire
color)
M432 (W)
M431 (B)
Receive
audio
signal 4 (Y) 3 (BR)
SKIA4278E
SKIA0177E