2004 INFINITI QX56 Factory Service Manual

oil door lock roof rack cooling instrument cluster dashboard warning lights

Load previous 8 pages

Page 185 of 3371

INFINITI QX56 2004 Factory Service Manual AT-114
DTC P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)
Revision: August 20072004 QX56
6. CHECK DTC
Perform “DTC Confirmation Procedure”.
Refer to AT-112, "DTC Confirmation Procedure" .
OK

Page 186 of 3371

INFINITI QX56 2004 Factory Service Manual DTC P0725 ENGINE SPEED SIGNAL
AT-115
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
DTC P0725 ENGINE SPEED SIGNALPFP:24825
DescriptionUCS002E1
The engine speed signal is sent from the ECM to

Page 187 of 3371

INFINITI QX56 2004 Factory Service Manual AT-116
DTC P0725 ENGINE SPEED SIGNAL
Revision: August 20072004 QX56
2. CHECK DTC WITH TCM
With CONSULT-II
1. Start engine.
2. Select “ECU INPUT SIGNALS” in “DATA MONITOR” mode for
“A/T” w

Page 188 of 3371

INFINITI QX56 2004 Factory Service Manual DTC P0725 ENGINE SPEED SIGNAL
AT-117
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
7. CHECK DTC
Perform “DTC Confirmation Procedure”.
Refer to AT- 11 5 , "DTC Confirmation Procedure"

Page 189 of 3371

INFINITI QX56 2004 Factory Service Manual AT-118
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE
Revision: August 20072004 QX56
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVEPFP:31940
DescriptionUCS002E7
The torque converter clutch soleno

AT-118
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE
Revision: August 20072004 QX56
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVEPFP:31940
DescriptionUCS002E7
The torque converter clutch solenoid valve is activated, with the gear in D4 , D5 by the TCM in response
to signals sent from the vehicle speed sensor and accelerator pedal position sensor (throttle position sen-
sor). Torque converter clutch piston operation will then be controlled.
Lock-up operation, however, is prohibited when A/T fluid temperature is too low.
When the accelerator pedal is depressed (less than 1/8) in lock-up condition, the engine speed should not
change abruptly. If there is a big jump in engine speed, there is no lock-up.
CONSULT-II Reference ValueUCS002E8
On Board Diagnosis LogicUCS002E9
This is an OBD-II self-diagnostic item.
Diagnostic trouble code “TCC SOLENOID/CIRC” with CONSULT-II or P0740 without CONSULT-II is
detected under the following conditions.
–When TCM detects an improper voltage drop when it tries to operate the solenoid valve.
–When TCM detects as irregular by comparing target value with monitor value.
Possible CauseUCS002EA
Torque converter clutch solenoid valve
Harness or connectors
(The solenoid circuit is open or shorted.)
DTC Confirmation ProcedureUCS002EB
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “DATA MONITOR” mode for “ENGINE” with CONSULT-II.
3. Start engine and maintain the following conditions for at least 5
consecutive seconds.
VHCL SPEED SE: 80 km/h (50 MPH) or more
ACCELE POS: 0.5/8 - 1.0/8
SELECTOR LEVER: “D” position
Driving location: Driving the vehicle uphill (increased
engine load) will help maintain the driving conditions
required for this test.
4. If DTC is detected go to AT-119, "
Diagnostic Procedure" .
WITH GST
Follow the procedure “With CONSULT-II”.
Item name Condition Display value (Approx.) (A)
TCC SOLENOIDWhen performing slip lock-up 0.2 - 0.4
When performing lock-up 0.4 - 0.6
BCIA0030E

Page 190 of 3371

INFINITI QX56 2004 Factory Service Manual DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE
AT-119
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
Diagnostic ProcedureUCS002EC
1. CHECK INPUT SIGNAL
With CONSULT-II
1. Turn ignition sw

Page 191 of 3371

INFINITI QX56 2004 Factory Service Manual AT-120
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE
Revision: August 20072004 QX56
6. CHECK DTC
Perform “DTC Confirmation Procedure”.
Refer to AT-118, "DTC Confirmation Procedure" .
OK or NG

Page 192 of 3371

INFINITI QX56 2004 Factory Service Manual DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)
AT-121
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)PFP:31940
DescriptionUCS002ED
This malfunction is detec

DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)
AT-121
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)PFP:31940
DescriptionUCS002ED
This malfunction is detected when the A/T does not shift into 5th gear position or the torque converter clutch
does not lock-up as instructed by the TCM. This is not only caused by electrical malfunction (circuits open or
shorted) but also by mechanical malfunction such as control valve sticking, improper solenoid valve operation,
etc.
CONSULT-II Reference ValueUCS002EE
On Board Diagnosis LogicUCS002EF
This is an OBD-II self-diagnostic item.
Diagnostic trouble code “A/T TCC S/V FNCTN” with CONSULT-II or P0744 without CONSULT-II is
detected under the following conditions.
–When A/T cannot perform lock-up even if electrical circuit is good.
–When TCM detects as irregular by comparing difference value with slip rotation.
Possible CauseUCS002EG
Harness or connectors
(The solenoid circuit is open or shorted.)
Torque converter clutch solenoid valve
Hydraulic control circuit
DTC Confirmation ProcedureUCS002EH
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Start engine and Select “TCC S/V FNCTN CHECK” of “DTC
WORK SUPPORT” mode for “A/T” with CONSULT-II and touch
“START”.
2. Accelerate vehicle to more than 80 km/h (50 MPH) and maintain
the following condition continuously until “TESTING” has turned
to “COMPLETE”. (It will take approximately 30 seconds after
“TESTING” shows.)
ACCELE POSI: More than 1.0/8 (at all times during step 4)
TCC SOLENOID: 0.4 - 0.6 A
Selector lever: “D” position
[Reference speed: Constant speed of more than 80 km/h (50
MPH)]
–Make sure “GEAR” shows “5”.
–For shift schedule, refer to AT- 6 7 , "Vehicle Speed When Performing and Releasing Complete Lock-
up" .
–If “TESTING” does not appear on CONSULT-II for a long time, select “SELF-DIAG RESULTS”. In
case a 1st trip DTC other than P0744 is shown, refer to applicable “TROUBLE DIAGNOSIS FOR
DTC”.
3. Make sure that “OK” is displayed. (If “NG” is displayed, refer to “DIAGNOSTIC PROCEDURE”.)
Refer to AT- 1 2 2 , "
Diagnostic Procedure" .
Refer to shift schedule, AT-67, "
Vehicle Speed When Performing and Releasing Complete Lock-up" .
Item name Condition Display value (Approx.) (A)
TCC SOLENOIDWhen performing slip lock-up 0.2 - 0.4
When performing lock-up 0.4 - 0.6
BCIA0030E

Load next 8 pages

Page: < prev 1-10 ... 153-160 161-168 169-176 177-184 185-192 193-200 201-208 209-216 217-224 ... 3376 next >

jacking air condition bolt pattern coolant charging wheel bolt torque