Page 25 of 3371
![INFINITI QX56 2004 Factory Service Manual ACS-16
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: August 20072004 QX56
The area is not suitable for the adjustment work.
ICC sensor is not clean.
8. After the CONSULT-II displays “ADJUST THE VER INFINITI QX56 2004 Factory Service Manual ACS-16
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: August 20072004 QX56
The area is not suitable for the adjustment work.
ICC sensor is not clean.
8. After the CONSULT-II displays “ADJUST THE VER](/manual-img/42/57034/w960_57034-24.png)
ACS-16
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: August 20072004 QX56
The area is not suitable for the adjustment work.
ICC sensor is not clean.
8. After the CONSULT-II displays “ADJUST THE VERTICAL OF
LASER BEAM AIMING” turn the vertical adjusting screw until
“U/D CORRECT” value is set in the range of ±4.
CAUTION:
Turn the screw slowly. The value on the CONSULT-II is
slower than the actual movement of the ICC sensor. Wait 2
seconds between each adjustment.
NOTE:
Turning the screw clockwise raises the ICC sensor and counter-
clockwise lowers the ICC sensor.
9. When “U/D CORRECT” value indicates ±4, confirm that the value remains within ±4 for at least 2 seconds
while nothing is touching the ICC sensor.
When “COMPLETED THE VERTICAL AIMING OF LASER
BEAM” appears on screen, touch “END”.
CAUTION:
Be sure that the margin of “U/D CORRECT” is within ±4
when the ICC sensor unit is untouched.
10. Confirm that “ADJUSTING AUTOMATIC HORIZONTAL LASER
BEAM AIMING” is on screen and wait while the horizontal
adjustment is made automatically. (maximum: 10 seconds).
SKIA1221E
WKIA1869E
WKIA2676E
SKIA1224E
Page 26 of 3371
LASER BEAM AIMING ADJUSTMENT
ACS-17
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: August 20072004 QX56
11. Confirm that “NORMALLY COMPLETED” is displayed on CON-
SULT-II and close the aiming adjustment procedure by touching
“END”.
CAUTION:
Complete all the procedures once “LASER BEAM ADJUST”
mode is entered in CONSULT-II. When the procedure is dis-
continued, the ICC system is inoperable.
CHECK AFTER THE ADJUSTMENT
Test the ICC system by performing the ICC System Running Test. Refer to ACS-9, "ICC System Running Test"
.
SKIA1225E
Page 27 of 3371
ACS-18
[ICC]
ELECTRICAL UNITS LOCATION
Revision: August 20072004 QX56
ELECTRICAL UNITS LOCATIONPFP:25230
Component Parts and Harness Connector LocationEKS007RP
WKIA1762E
Page 28 of 3371
WIRING DIAGRAM
ACS-19
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: August 20072004 QX56
WIRING DIAGRAMPFP:00000
SchematicEKS007RG
WKWA3125E
Page 29 of 3371
ACS-20
[ICC]
WIRING DIAGRAM
Revision: August 20072004 QX56
Wiring Diagram — ICC —EKS007RH
WKWA1184E
Page 30 of 3371
WIRING DIAGRAM
ACS-21
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: August 20072004 QX56
WKWA1185E
Page 31 of 3371
ACS-22
[ICC]
WIRING DIAGRAM
Revision: August 20072004 QX56
WKWA1186E
Page 32 of 3371
WIRING DIAGRAM
ACS-23
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: August 20072004 QX56
WKWA3126E