Page 3257 of 6000

8F–62BODY STRUCTURE
7. Remove glass run.
Pull the glass run (6) out from the door frame
groove.
631RS007
8. Remove rear guide rail.
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Apply soap and water to the door frame groove. Insert
the glass run (1) to the door frame from the A corner in
the arrow–marked directions.
Install the glass run with its wider end pointed to the
inside of the vehicle.
A10RS023
2. Set the glass into the door panel with the front side of
the glass lowered and insert the rear side of the glass
into the glass run (1). Then insert the front side of the
glass into the glass run in order to install the glass to
the glass run while raising it up along the glass run.
3. Tighten the window regulator and the glass fixing
bolts and nuts to the specified torque.
Torque : 8 N
m (0.8kgꞏm/69 lb in)4. Check to see of the window regulator operates
smoothly and the glass opens and closes properly.
Install the waterproof sheet with no clearance
between the door panel and the waterproof sheet.
Page 3258 of 6000
8F–63 BODY STRUCTURE
Rear Window Regulator And Glass
Parts Location
651RW018
Legend
(1) Window Regulator
(2) Glass
(3) Cable Fixing Clip(4) Window Regulator Motor Connector
(5) Door Trim Panel
(6) Waterproof Sheet
Removal
1. Disconnect the battery ground cable.
2. Remove door trim panel.
Refer to Door Trim Panel (Rear) removal procedure
in this section.
3. Remove waterproof sheet (1).
Taking notice of the door harness, peel the
waterproof sheet off the door panel carefully.
651RS002
Page 3259 of 6000
8F–64BODY STRUCTURE
4. Remove glass.
Bring the glass down to the position where the bolt
can be seen.
Remove the sash division 2 fixing bolts (1) and then
remove the glass fixing bolt to remove the glass
upwards.
651RS003
651RW010
5. Remove window regulator.
Disconnect the regulator motor connector (4) and
remove the window regulator cable fixing clip (3)
from the door panel, if model is equipped with power
windows.
Remove the window regulator 7 fixing bolts (2) and
pull the regulator out from the lower hole of the door
panel.
651RW011
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Tighten the window regulator and the glass fixing
bolts to the specified torque.
Torque : 8 N
m (0.8kgꞏm/69 lb in)
2. Install the waterproof sheet with no clearance
between the door panel and the waterproof sheet.
Page 3260 of 6000
8F–65 BODY STRUCTURE
Rear Door Fixed Glass And Glass Run
Parts Location
651RW019
Legend
(1) Glass Run
(2) Rear Fixed Glass
(3) Sash Division(4) Sash Division Fixing Bolts
(5) Door Trim Panel
(6) Waterproof Sheet
(7) Glass
Removal
1. Disconnect the battery ground cable.
2. Remove door trim panel.
3. Remove waterproof sheet.
4. Remove glass.
Refer to Window Regulator and Glass removal
procedure in this section.
5. Remove glass run.
Pull the glass run (1) out from the door frame.
651RS007
Page 3261 of 6000
8F–66BODY STRUCTURE
6. Remove sash division (2).
651RS008
7. Remove door fixed glass.
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Apply soap and water to the fixed glass.
2. Apply soap and water to the door groove and insert
the glass run (3) to the frame from the corner in the
arrow-marked directions.
3. Be sure to install the glass run with its end pointed to
the inside of the vehicle.
A10RW019
Page 3262 of 6000
8F–67 BODY STRUCTURE
Front Door Sash Moulding
Parts Location
645RS001
Legend
(1) Front Door Sash Moulding
Removal
1. Remove front door slash moulding.
To avoid the weatherstrip (1) and pry the door sash
moulding (2) out from the door panel.
645RS002
Installation
1. Install the front door sash moulding.
Assemble the edge portion (A portion) of the
moulding so that the clearance between the
moulding and the waist seal becomes 1 mm (0.04
in).
Page 3263 of 6000
8F–68BODY STRUCTURE
Rear Door Moulding
Parts Location
645RS003
Legend
(1) Rear Door Side Moulding(2) Rear Door Corner Moulding
(3) Rear Door Upper Moulding
Removal
1. Disconnect the battery ground cable.
2. Remove rear door side moulding.
3. Remove rear door upper moulding.
4. Remove rear door corner moulding.
Avoiding the weatherstrip (3), pry the moulding (2)
out from the door frame (1).
645RS004
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Install each moulding with no clearance between
each piece of moulding.
2. Assemble the edge portion (A portion) of the
moulding so that the clearance between the rear side
moulding and the waist seal is 1 mm (0.04 in).
Page 3264 of 6000
8F–69 BODY STRUCTURE
Front Door Waist Seal
Parts Location
631RS009
Legend
(1) Nylon Washer(2) Door Mirror
(3) Front Door Waist Seal
Removal
1. Disconnect the battery ground cable.
2. Remove door mirror.
Refer to Exterior / Interrior Trim in this section.
3. Remove front door waist seal.
Remove the fixing screw and pull out the waist seal
(1) from the door frame while prying it up.
631RS010
Installation
1. Install the front door waist seal.
Apply soap and water to the inside of the waist seal
and align the screw hole of the waist seal to the door
panel hole, and gently tap the seal with a rubber
hammer.
Be sure not to tap the seal hard. This may result in
deforming the seal.
2. Install the door mirror.