Page 3425 of 6000

SEAT BELT SYSTEM 9A–5
Inspection of retractor
1. ELR (Emergency Locking Retractor) lock inclining
angle check.
When the retractor is moved gently from its installing
position, make sure it is not locked within 15° in any
directions, and it remains locked at 45° or larger.
2. ELR lock check.
When the seat belt is drawn slowly with the retractor
installed, make sure it is not locked. And when it is
drawn quickly, make sure it is locked.
3. ALR (Automatic Locking Retractor)/ELR check
(Except for driver’s seat).
When rewound after winding out the seat belt, make
sure the seat belt cannot be taken out. After
rewinding, make sure it has returned to its normal
operation.
CAUTION: Do not disassemble the retractor.
Installation
To install, follow the removal steps in the reverse order,
noting the following points;
1. Pass the seat belt through the lower trim cover hole,
and tighten the seat belt anchor bolts to the specified
torque.
Torque: 39 Nꞏm (4.0 kgꞏm/29 lb ft)
2. After installing the trim cover to the body panel
securely, close the lower trim cover.
Page 3426 of 6000

9A–6 SEAT BELT SYSTEM
760RS006
Legend
(1) Rear Seat Belt Anchor Bolt Cover and Anchor
Bolt (Upper Side)
(2) Quarter Upper Trim Cover
(3) Rear Seat Belt Assembly(4) Dust Cover
(5) Retractor
(6) Anchor Bolt (Lower Side)
(7) Luggage Side Trim Cover
(8) Rear End Floor Trim Cover
Rear Seat Belt and Associated Parts (Long Wheel Base)
12
3
4
5
6 7
8
Removal
1. Disconnect the battery ground cable.
2. Remove the rear end floor trim cover.
3. Remove the luggage side trim cover.
Refer to Luggage Side and Quarter Upper Trim
Panel removal steps in Exterior/Interior Trim
section.
4. Remove the rear seat belt anchor bolt cover and
anchor bolt (Upper Side).
5. Remove the seat belt lower anchor bolt and remove
the retractor from dust cover slit to remove the rear
seat belt.
Inspection
If any of the following abnormalities is found, replace on
an assembly basis;
No smooth move of upper/lower anchors in the
circumferential direction.
Damaged and/or deformed through ring.
Damaged and/or deformed tongue.
Damaged and/or frayed of webbing.
Deformed retractor bracket.
Seat belt not rewound up.
Resistance or abnormal sound when seat belt is
wound out and rewound.
Retractor abnormality.
Page 3427 of 6000
SEAT BELT SYSTEM 9A–7
Inspection of retractor
1. ELR (Emergency Locking Retractor) lock inclining
angle check.
When the retractor is moved gently from its installing
position, make sure it is not locked within 15° in any
directions, and it remains locked at 45° or larger.
2. ELR lock check.
When the seat belt is drawn slowly with the retractor
installed, make sure it is not locked. And when it is
drawn quickly, make sure it is locked.
3. ALR (Automatic Locking Retractor)/ELR check
(Except for driver’s seat).
When rewound after winding out the seat belt, make
sure the seat belt cannot be taken out. After
rewinding, make sure it has returned to its normal
operation.
CAUTION: Do not disassemble the retractor.
Installation
To install, follow the removal steps in the reverse order,
noting the following point.
1. Tighten the seat belt anchor bolts to the specified
torque.
Torque: 39 Nꞏm (4.0 kgꞏm/29 lb ft)
Page 3428 of 6000
9A–8 SEAT BELT SYSTEM
760RW025
Legend
(1) Rear Seat Belt Upper Anchor Bolt Cover and
Anchor Bolt
(2) Quarter Upper Trim Cover
(3) Dust Cover
(4) Retractor(5) Rear Seat Belt Lower Anchor Bolt Cover and
Anchor Bolt
(6) Luggage Side Trim Cover
(7) Rear End Floor Trim Cover
(8) Rear Seat Belt Assembly
Rear Seat Belt and Associated Parts (Short Wheel Base)
1
82
34
56
7
Removal
1. Disconnect the battery ground cable.
2. Remove the rear seat belt lower anchor bolt cover (1)
and anchor bolt (2).1
2
755RW038
Page 3429 of 6000

SEAT BELT SYSTEM 9A–9
3. Remove the rear end floor trim cover.
4. Remove the luggage side trim cover.
Refer to Luggage Side and Quarter Upper Trim
Panel removal steps in Exterior/Interior Trim
section.
5. Remove the rear seat belt upper anchor bolt cover (1)
and anchor bolt.6. Remove the rear seat belt assembly.
Remove the seat belt lower anchor bolt and screw.
Remove the retractor from the dust cover slit.
Inspection
If any of the following abnormalities is found, replace on
an assembly basis;
No smooth move of upper/lower anchors in the
circumferential direction.
Damaged and/or deformed through ring.
Damaged and/or deformed tongue.
Damaged and/or frayed of webbing.
Deformed retractor bracket.
Seat belt not rewound up.
Resistance or abnormal sound when seat belt is
wound out and rewound.
Retractor abnormality.
Inspection of retractor
1. ELR (Emergency Locking Retractor) lock inclining
angle check.
When the retractor is moved gently from its installing
position, make sure it is not locked within 15° in any
directions, and it remains locked at 45° or larger.
2. ELR lock check.
When the seat belt is drawn slowly with the retractor
installed, make sure it is not locked. And when it is
drawn quickly, make sure it is locked.
3. ALR (Automatic Locking Retractor)/ELR check
(Except for driver’s seat).
When rewound after winding out the seat belt, make
sure the seat belt cannot be taken out. After
rewinding, make sure it has returned to its normal
operation.
CAUTION: Do not disassemble the retractor.
Installation
To install, follow the removal steps in the reverse order,
noting the following point.
1. Be sure to install the lower side anchor plate straight
horizontally, with mounting hole of the plate at the
center.
2. Tighten the seat belt anchor bolts to the specified
torque.
Torque: 39 Nꞏm (4.0 kgꞏm/29 lb ft)
1
755RW039
Page 3430 of 6000
9A–10 SEAT BELT SYSTEM
Third Seat Belt and Associated Parts (Long Wheel Base)
65 1
2
3
4
7
760RW027
Legend
(1) Third Seat Belt Upper Anchor Bolt Cover and
Anchor Bolt
(2) Third Seat Belt Assembly
(3) Dust Cover(4) Retractor
(5) Luggage Side Trim Cover
(6) Third Seat Belt Lower Anchor Bolt Cover and
Anchor Bolt
(7) Rear End Floor Trim Cover
Removal
1. Disconnect the battery ground cable.
2. Remove the rear end floor trim cover.
3. Remove the luggage side trim cover.
Refer to Luggage Side and Quarter Upper Trim
Panel removal steps in Exterior/Interior Trim
section.
4. Remove the third seat belt anchor bolt cover and
anchor bolt (Upper Side).
5. Remove the seat belt lower anchor bolt and remove
the retractor from dust cover slit to remove the third
seat belt.
1
755RW043
Page 3431 of 6000

SEAT BELT SYSTEM 9A–11
Inspection
If any of the following abnormalities is found, replace on
an assembly basis;
No smooth move of upper/lower anchors in the
circumferential direction.
Damaged and/or deformed through ring.
Damaged and/or deformed tongue.
Damaged and/or frayed of webbing.
Deformed retractor bracket.
Seat belt not rewound up.
Resistance or abnormal sound when seat belt is
wound out and rewound.
Retractor abnormality.
Inspection of retractor
1. ELR (Emergency Locking Retractor) lock inclining
angle check.
When the retractor is moved gently from its installing
position, make sure it is not locked within 15° in any
directions, and it remains locked at 45° or larger.
2. ELR lock check.
When the seat belt is drawn slowly with the retractor
installed, make sure it is not locked. And when it is
drawn quickly, make sure it is locked.
CAUTION: Do not disassemble the retractor.
Installation
To install, follow the removal steps in the reverse order,
noting the following point.
1. Be sure to install the lower side anchor plate (1)
straight against the longitudinal direction of the
vehicle with mounting hole of the plate at the center.
2. Tighten the seat belt anchor bolts to the specified
torque.
Torque: 39 Nꞏm (4.0 kgꞏm/29 lb ft)
Page 3432 of 6000

9A–12 SEAT BELT SYSTEM
Front Seat Buckle Assembly
Removal
1. Disconnect the battery ground cable.
2. Disconnect the seat belt warning connector (If so
equipped).
3. Remove the front seat buckle assembly(1).
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Fix the buckle to the rotation – stop position(2)
securely to install the front seat buckle assembly(1).
2. Tighten the buckle anchor bolt to the specified torque.
Torque: 39 Nꞏm (4.0 kgꞏm/29 lb ft)
1
760RW023
1
2
760RS005
Front Seat Buckle Assembly (W/Pretensioner)
Removal
1. Disconnect the battery ground cable.
2. Disconnect the pretensioner harness connector(3).
3. Remove the pretensioner cover(1).
4. Remove the front seat buckle assembly(2).
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Fix the buckle to the rotation – stop position securely
to install the front seat buckle assembly.
2. Connect the pretensioner harness connector.
3. Tighten the buckle anchor bolt to the specified torque.
Torque: 39 Nꞏm (4.0 kgꞏm/29 lb ft)
123
760RW030760RW029