Page 841 of 2543
QUARTER WINDOW GLASS
COMPONENTS
BO±36± BODYQUARTER WINDOW GLASS
Page 842 of 2543
QUARTER WINDOW GLASS REMOVAL
1. REMOVE THESE PARTS:
(See pages BO±59 to BO±61)
(a) Tonneau cover
(b) Luggage compartment mat
(c) Spare wheel cover
(d) Rear seatback
(e) Removable roof stay RH and LH (Sport roof)
(f) Deck trim rear cover
(g) Removable roof holder (Sport roof)
(h) Quarter wheel house inner cover
(i) Speaker grille
(j) Deck trim side board
(k) Front door scuff inside plate
(l) Rear quarter trim board
(m) Front seat outer belt shoulder anchor
(n) Rear seat outer belt floor anchor
(o) Roof side inner garnish
(p) Rear roof headlining (Sport roof)
2. REMOVE ROOF SIDE RAIL WEATHERSTRIP
(a) Using the clip remover, remove 3 clips from the rear side of
the weatherstrip.
(b) Remove the rear side of the weatherstrip from the retainer.
3. REMOVE ROOF SIDE RAIL WEATHERSTRIP RETAINER
Remove the outside garnish seal and retainer.
4. REMOVE QUARTER WINDOW GLASS
(a) Remove the 3 nuts.
± BODYQUARTER WINDOW GLASSBO±37
Page 843 of 2543
(b) Push piano wire through from the interior.
(c) Tie both wire ends to a wooden block or similar object.
HINT: Apply adhesive tape to the outer surface to keep the
surface from being scratched.
NOTICE: When separating the glass, take care not to
damage the paint and exterior.
(d) Cut the adhesive by pulling the piano wire around it.
HINT: Cut the adhesive areas in the order as shown in the il-
lustration, so leave the adhesive where the glass retainer
stays.
(e) Let the piano wire pass as shown on the illustration and cut
the rest of adhesive by pulling the piano wire.
NOTICE: Do not damage the glass retainers.
(f) Remove the glass.
NOTICE: Leave as much of the adhesive on the body as
possible when cutting off the glass.
QUARTER WINDOW GLASS
INSTALLATION
Installation is in the reverse order of removal. BO±38
± BODYQUARTER WINDOW GLASS
Page 844 of 2543
BACK DOOR MOULDING AND
GLASS
COMPONENTS
± BODYBACK DOOR MOULDING AND GLASSBO±39
Page 845 of 2543

BACK DOOR MOULDING AND GLASS
REMOVAL
1. DISCONNECT DEFOGGER CONNECTOR
2. REMOVE THESE PARTS:
(a) Rear wiper arm and blade
(b) Back door trim board
(c) Back door opening trim
3. REMOVE BACK DOOR MOULDING
Using a knife, cut off the moulding as shown.
NOTICE: Do not damage the body with the knife.
4. REMOVE BACK DOOR GLASS AND MOULDING
HINT: Remove the glass and moulding in the same manner
as the windshield. (See pages BO±31 and 32)
BACK DOOR MOULDING AND GLASS
INSTALLATION
1. INSTALL BACK DOOR MOULDING
Place the moulding around the glass and install it by hand.
HINT: Always remove the back door glass to install the
moulding.
2. INSTALL BACK DOOR GLASS
HINT: Install the glass in the same manner as the windshield.
(See pages BO±32 to 35)
(a) Coat contact surface of the glass with primer ºGº.
(b) Apply adhesive.
H: 12 mm (0.47 in.)
3. INSTALL THESE PARTS:
(a) Back door opening trim
(b) Back door trim board
(c) Rear wiper arm and blade
Torque: 11 NVm (110 kgfVcm, 8.0 ftVlbf)
4. CONNECT DEFOGGER CONNECTOR BO±40
± BODYBACK DOOR MOULDING AND GLASS
Page 846 of 2543
SPORT ROOF
COMPONENTS
± BODYSPORT ROOFBO±41
Page 847 of 2543
ON±VEHICLE INSPECTION
INSPECT REMOVABLE ROOF PANEL ALIGNMENT
(a) With the removable roof installed, check for water leakage.
(b) Check for a difference in clearance and level between the
removable roof panel and roof panel.
Clearance:
Front side: 6.0+1.5 mm (0.236+0.06 in.)
Rear side: 6.0+1.5 mm (0.236+0.06 in.)
Level: (Rear side)
RH/LH side: +1.5 ~±2.0 mm (+0.06~±0.08 in.)
Center: +1.0~±2.0 mm (+0.04~±0.08 in.)
Zero level: upper surface of roof panel
REMOVABLE ROOF ADJUSTMENT
1. REMOVE ROOF HEADLINING
(a) Removable roof headlining ± for clearance adjustment (See
pages BO±41 and 61)
(b) Rear roof headlining ± for level adjustment (See pages
BO±58 to 61) BO±42
± BODYSPORT ROOF
Page 848 of 2543
2. ADJUST CLEARANCE
Adjust the removable roof bracket by loosening the remov-
able roof bracket bolts.
If the clearance is not within specification, repair the body
panel.
3. ADJUST LEVEL
Select the shim that makes the difference between the rear
side of removable roof panel and rear roof panel a minimum.
Shim thickness:
1.0 mm (0.039 in.)
2.0 mm (0.079 in.)
4. INSTALL ROOF HEADLINING
Installation is in the reverse order to removal.
REMOVABLE ROOF DISASSEMBLY AND
ASSEMBLY
1. DISASSEMBLE THESE PARTS:
(a) Roof side rail weatherstrip
(b) Removable roof moulding
(c) Roof headlining
(d) Removable roof lock
(e) Bracket No.2
2. ASSEMBLE THESE PARTS:
(a) Bracket No.2
(b) Removable roof lock
(c) Roof headlining
(d) Removable roof moulding
3. APPLY SEAL PACKING
Apply seal packing on the removable roof moulding as shown
in the illustration.
L: 4 mm (0.16 in.)
Part No. 08826±00080
4. INSTALL ROOF SIDE RAIL WEATHERSTRIP
± BODYSPORT ROOFBO±43