2004 SUBARU FORESTER Service Repair Manual

diagnostic menu child lock ESP driver seat adjustment water pump key fob battery

Load previous 8 pages

Page 2145 of 2870

SUBARU FORESTER 2004 Service Repair Manual EN(H4DOTC 2.5)-121
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
W: DTC P0223 THROTTLE/PEDAL POSITION SENSOR/SWITCH “B” CIRCUIT
HIGH INPUT
DTC DETECTING CONDITION:
I

Page 2146 of 2870

SUBARU FORESTER 2004 Service Repair Manual EN(H4DOTC 2.5)-122
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
WIRING DIAGRAM:
Step Check Yes No
1 CHECK SENSOR OUTPUT.
1) Turn the ignition switch to ON.
2) Read the d

Page 2147 of 2870

SUBARU FORESTER 2004 Service Repair Manual EN(H4DOTC 2.5)-123
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
2 CHECK POOR CONTACT.
Check the poor contact in connector between
ECM and electronic throttle control.Is

EN(H4DOTC 2.5)-123
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
2 CHECK POOR CONTACT.
Check the poor contact in connector between
ECM and electronic throttle control.Is there poor contact in con-
nector between ECM and elec-
tronic throttle control?Repair the poor
contact.Temporary poor
contact occurred,
but it is normal at
present.
3 CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from ECM.
3) Disconnect the connectors from the elec-
tronic throttle control.
4) Measure the resistance between ECM con-
nector and electronic throttle control connector.
Connector & terminal
(B136) No. 29 — (E57) No. 4:
(B136) No. 35 — (E57) No. 3:Is the resistance less than 1
Ω?Go to step 4.Repair the open
circuit of harness
connector.
4 CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL.
1) Connect the ECM connector.
2) Measure the resistance between electronic
throttle control connector and engine ground.
Connector & terminal
(E57) No. 3 — Engine ground:Is the resistance less than 5
Ω?Go to step 5.Repair the poor
contact in ECM
connector. Replace
the ECM if defec-
tive. FU(H4DOTC 2.5)-
41, Engine Con-
trol Module
(ECM).>
5 CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL.
1) Connect the ECM connector.
2) Turn the ignition switch to ON.
3) Measure the voltage between electronic
throttle control connector and engine ground.
Connector & terminal
(E57) No. 5 (+) — Engine ground (
−):
4) Check the voltage change by shaking the
harness and connector of ECM and engine
harness connector while monitoring the value
with voltage meter.Is the voltage more than 10 V? Go to step 6.Repair battery
short circuit in har-
ness between
ECM connector
and electronic
throttle control
connector.
6 CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL.
1) Measure the voltage between electronic
throttle control connector and engine ground.
Connector & terminal
(E57) No. 4 (+) — Engine ground (
−):
2) Check the voltage change by shaking the
harness and connector of ECM and engine
harness connector while monitoring the value
with voltage meter.Is the voltage less than 10 V? Go to step 7.Repair battery
short circuit in har-
ness between
ECM connector
and electronic
throttle control
connector.
7 CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from ECM.
3) Measure the resistance between connector
terminals.
Connector & terminal
(B136) No. 29 — (B136) No. 16:Is the resistance more than 1
MΩ?Repair the poor
contact. Replace
the electronic
throttle control if
defective.Sensor power sup-
ply circuit may be
shorted. Step Check Yes No

Page 2148 of 2870

SUBARU FORESTER 2004 Service Repair Manual EN(H4DOTC 2.5)-124
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
X: DTC P0230 FUEL PUMP PRIMARY CIRCUIT
DTC DETECTING CONDITION:
Immediately at fault recognition
CAUTION:

Page 2149 of 2870

SUBARU FORESTER 2004 Service Repair Manual EN(H4DOTC 2.5)-125
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK POWER SUPPLY CIRCUIT TO FUEL
PUMP CONTROL UNIT.
1) Turn the ignition switch to

EN(H4DOTC 2.5)-125
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK POWER SUPPLY CIRCUIT TO FUEL
PUMP CONTROL UNIT.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from fuel pump
control unit.
3) Turn the ignition switch to ON.
4) Measure the voltage between fuel pump
control unit and chassis ground.
Connector & terminal
(R122) No. 10 (+) — Chassis ground (
−):Is the voltage more than 10 V? Go to step 2.Repair the power
supply circuit.
N
OTE:
In this case repair
the following:
Open or ground
short circuit in har-
ness between fuel
pump relay and
fuel pump control
unit.
Poor contact in
fuel pump control
unit connector.
Poor contact in
fuel pump relay
connector.
2 CHECK GROUND CIRCUIT OF FUEL PUMP
CONTROL UNIT.
1) Turn the ignition switch to OFF.
2) Measure the resistance of harness
between fuel pump control unit and chassis
ground.
Connector & terminal
(R122) No. 5 — Chassis ground:Is the resistance less than 5
Ω?Go to step 3.Repair the harness
and connector.
NOTE:
In this case repair
the following:
Open circuit
between fuel pump
control unit and
chassis ground.
Poor contact in
fuel pump control
unit connector.
3 CHECK HARNESS BETWEEN FUEL PUMP
CONTROL UNIT AND FUEL PUMP CONNEC-
TOR.
1) Disconnect the connector from fuel pump.
2) Measure the resistance of harness
between fuel pump control unit and fuel pump
connector.
Connector & terminal
(R122) No. 6 — (R58) No. 4:
(R122) No. 7 — (R58) No. 1:Is the resistance less than 1
Ω?Go to step 4.Repair open circuit
between fuel pump
control unit and
fuel pump.
4 CHECK HARNESS BETWEEN FUEL PUMP
CONTROL UNIT AND FUEL PUMP CONNEC-
TOR.
Measure the resistance of harness between
fuel pump control unit and chassis ground.
Connector & terminal
(R122) No. 6 — Chassis ground:
(R122) No. 7 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 5.Repair ground
short circuit
between fuel pump
control unit and
fuel pump.
5 CHECK HARNESS BETWEEN FUEL PUMP
CONTROL UNIT AND ECM CONNECTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from ECM.
3) Measure the resistance in harness
between fuel pump control unit and ECM con-
nector.
Connector & terminal
(R122) No. 8 — (B137) No. 28:
(R122) No. 9 — (B135) No. 27:Is the resistance less than 1
Ω?Go to step 6.Repair the harness
and connector.
N
OTE:
In this case repair
the following:
Open circuit
between fuel pump
control unit and
ECM.
Poor contact in
fuel pump control
unit and ECM con-
nector

Page 2150 of 2870

SUBARU FORESTER 2004 Service Repair Manual EN(H4DOTC 2.5)-126
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
6 CHECK HARNESS BETWEEN FUEL PUMP
CONTROL UNIT AND ECM CONNECTOR.
Measure the resistance of harness betw

Page 2151 of 2870

SUBARU FORESTER 2004 Service Repair Manual EN(H4DOTC 2.5)-127
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Y: DTC P0245 TURBO/SUPER CHARGER WASTEGATE SOLENOID “A” LOW
DTC DETECTING CONDITION:
Immediately at f

Page 2152 of 2870

SUBARU FORESTER 2004 Service Repair Manual EN(H4DOTC 2.5)-128
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK OUTPUT SIGNAL FROM ECM.
1) Turn the ignition switch to ON.
2) Measure the volta

EN(H4DOTC 2.5)-128
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK OUTPUT SIGNAL FROM ECM.
1) Turn the ignition switch to ON.
2) Measure the voltage between ECM and
chassis ground.
Connector & terminal
(B134) No. 32 (+) — Chassis ground (
−):Is the voltage more than 10 V? Even if the mal-
function indicator
light illuminates,
the circuit has
returned to a nor-
mal condition at
this time.Go to step 2.
2 CHECK HARNESS BETWEEN WASTEGATE
CONTROL SOLENOID VALVE AND ECM
CONNECTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from wastegate
control solenoid valve and ECM.
3) Measure the resistance in harness
between wastegate control solenoid valve con-
nector and engine ground.
Connector & terminal
(B127) No. 1 — Engine ground:Is the resistance less than 10
Ω?Repair ground
short circuit in har-
ness between
ECM and waste-
gate control sole-
noid valve
connector.Go to step 3.
3 CHECK HARNESS BETWEEN WASTEGATE
CONTROL SOLENOID VALVE AND ECM
CONNECTOR.
Measure the resistance of harness between
wastegate control solenoid valve and ECM.
Connector & terminal
(B134) No. 32 — (B127) No. 1:Is the resistance less than 1
Ω?Go to step 4.Repair open circuit
in harness
between ECM and
wastegate control
solenoid valve
connector.
N
OTE:
In this case repair
the following:
Open circuit in
harness between
ECM and waste-
gate control sole-
noid valve
connector
4 CHECK WASTEGATE CONTROL SOLE-
NOID VALVE.
1) Remove the wastegate control solenoid
valve.
2) Measure the resistance between wastegate
control solenoid valve terminals.
Te r m i n a l s
No. 1 — No. 2:Is the resistance 30 — 34 Ω? Go to step 5.Replace the
wastegate control
solenoid valve.
FU(H4DOTC 2.5)-
35, Wastegate
Control Solenoid
Va l ve . >
5 CHECK POWER SUPPLY TO WASTEGATE
CONTROL SOLENOID VALVE.
1) Turn the ignition switch to ON.
2) Measure the voltage between wastegate
control solenoid valve and engine ground.
Connector & terminal
(B127) No. 2 (+) — Engine ground (
−):Is the voltage more than 10 V? Go to step 6.Repair open circuit
in harness
between main
relay and waste-
gate control sole-
noid valve
connector.
6 CHECK POOR CONTACT.
Check poor contact in wastegate control sole-
noid valve connector.Is there poor contact in waste-
gate control solenoid valve
connector?Repair poor con-
tact in wastegate
control solenoid
valve connector.Contact the SUB-
ARU dealer.
N
OTE:
Inspection by DTM
is required, because
probable cause is
deterioration of mul-
tiple parts.

Load next 8 pages

Page: < prev 1-10 ... 2113-2120 2121-2128 2129-2136 2137-2144 2145-2152 2153-2160 2161-2168 2169-2176 2177-2184 ... 2872 next >

parking sensors alternator belt run flat keyless entry service interval reset width