2004 SUBARU FORESTER Service Repair Manual

wiring diagram seat memory open hood oil change homelink automatic transmission

Page 2617 of 2870

SUBARU FORESTER 2004 Service Repair Manual 4AT(H4DOTC)-41
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
59 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to

4AT(H4DOTC)-41
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
59 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM and
inhibitor switch.
3) Measure the resistance of harness
between TCM and inhibitor switch connector.
Connector & terminal
(B54) No. 10 — (T7) No. 6:Is the resistance less than 1
Ω?Go to step 60.Repair the open cir-
cuit in harness
between TCM and
inhibitor switch con-
nector, and poor
contact in coupling
connector.
60 CHECK INPUT SIGNAL FOR TCM.
1) Turn the ignition switch to OFF.
2) Connect the connector to TCM and inhibitor
switch.
3) Turn the ignition switch to ON.
4) Shift the select lever to “1” range.
5) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B54) No. 10 (+) — Chassis ground (–):Is the voltage less than 1 V? Go to step 61.Go to step 65.
61 CHECK INPUT SIGNAL FOR TCM.
1) Shift the select lever except for “1” range.
2) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B54) No. 10 (+) — Chassis ground (–):Is the voltage more than 8 V? Go to step 65.Replace the TCM.
Transmission Con-
trol Module
(TCM).>
62 CHECK “1” RANGE INDICATOR LIGHT
BULB.
1) Turn the ignition switch to OFF.
2) Remove the combination meter.
3) Remove the “1” range indicator light bulb
from combination meter.Is the “1” range indicator light
bulb OK?Go to step 63.Replace the “1”
range indicator light
bulb. 10, Combination
Meter Assembly.>
63 CHECK HARNESS CONNECTOR BETWEEN
TCM AND COMBINATION METER.
1) Disconnect the connectors from TCM and
combination meter.
2) Measure the resistance of harness
between TCM and combination meter.
Connector & terminal
(B54) No. 10 — (i12) No. 5:Is the resistance less than 1Ω? Go to step 65.Repair the open
circuit in harness
between TCM and
combination meter,
poor contact in
TCM connector.
64 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM,
inhibitor switch and combination meter.
3) Measure the resistance of harness
between TCM connector and chassis ground.
Connector & terminal
(B54) No. 10 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 65.Repair the ground
short circuit in “1”
range circuit.
65 CHECK POOR CONTACT.Is there poor contact in inhibi-
tor switch circuit?Repair the poor
contact.Go to step 66.
66 CHECK INHIBITOR SWITCH.Is the inhibitor switch in proper
position?Replace the TCM.
Transmission Con-
trol Module
(TCM).>Adjust the inhibi-
tor switch and
select cable. to 4AT-51, Inhibi-
tor Switch.> and
Select Cable.> Step Check Yes No

Page 2618 of 2870

SUBARU FORESTER 2004 Service Repair Manual 4AT(H4DOTC)-42
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
B: DTC P0712 TRANSMISSION FLUID TEMPERATURE SENSOR CIRCUIT LOW
INPUT
DTC DETECTING CONDITION

Page 2619 of 2870

SUBARU FORESTER 2004 Service Repair Manual 4AT(H4DOTC)-43
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
2 CHECK HARNESS CONNECTOR BETWEEN
TCM AND ATF TEMPERATURE SENSOR.
Measure the resistance of

4AT(H4DOTC)-43
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
2 CHECK HARNESS CONNECTOR BETWEEN
TCM AND ATF TEMPERATURE SENSOR.
Measure the resistance of harness between
TCM and transmission connector.
Connector & terminal
(B55) No. 9 — (B11) No. 15:Is the resistance less than 1
Ω?Go to step 3.Repair the open
circuit in harness
between TCM and
transmission con-
nector.
3 CHECK HARNESS CONNECTOR BETWEEN
TCM AND ATF TEMPERATURE SENSOR.
Measure the resistance of harness between
TCM connector and chassis ground.
Connector & terminal
(B55) No. 21 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 4.Repair the short
circuit in harness
between TCM and
transmission con-
nector.
4 CHECK HARNESS CONNECTOR BETWEEN
TCM AND ATF TEMPERATURE SENSOR.
Measure the resistance of harness between
TCM connector and chassis ground.
Connector & terminal
(B55) No. 9 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 5.Repair the short
circuit in harness
between TCM and
transmission con-
nector.
5 CHECK ATF TEMPERATURE SENSOR.
1) Turn the ignition switch to OFF.
2) Connect the connectors to transmission
and TCM.
3) Turn the ignition switch to ON and start
engine.
4) Warm-up the transmission until ATF tem-
perature reaches to 80°C (176°F).
N
OTE:
If ambient temperature is below 0°C (32°F),
drive the vehicle until ATF reaches its operating
temperature.
5) Disconnect the connector from transmis-
sion.
6) Measure the resistance between transmis-
sion connector terminals.
Connector & terminal
(T4) No. 11 — No. 15:Is the resistance 500 — 600
Ω?Go to step 6.Go to step 11.
6 CHECK ATF TEMPERATURE SENSOR.
Measure the resistance between transmission
connector terminals.
Connector & terminal
(T4) No. 11 — No. 15:Does the resistance value
increase when ATF tempera-
ture decreases?Go to step 7.Go to step 11.
7 PREPARE SUBARU SELECT MONITOR.Do you have a Subaru Select
Monitor?Go to step 9.Go to step 8.
8 CHECK INPUT SIGNAL FOR TCM.
1) Connect the connector to transmission.
2) Warm-up the transmission until ATF tem-
perature is about 80°C (176°F).
N
OTE:
If ambient temperature is below 0°C (32°F),
drive the vehicle until ATF reaches its operating
temperature.
3) Measure the voltage between TCM con-
nector terminal.
Connector & terminal
(B55) No. 9 (+) — No. 21 (
−):Is the voltage 1.5 — 1.9 V? Even if the POWER
indicator light was
blinking the circuit
has returned to a
normal condition at
this time. Tempo-
rary poor contact of
the connector or
harness may be the
cause. Repair the
harness or contact
in ATF temperature
sensor and trans-
mission connector.Go to step 10. Step Check Yes No

Page 2620 of 2870

SUBARU FORESTER 2004 Service Repair Manual 4AT(H4DOTC)-44
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
9 CHECK INPUT SIGNAL FOR TCM USING
SUBARU SELECT MONITOR.
1) Connect the connector to transm

4AT(H4DOTC)-44
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
9 CHECK INPUT SIGNAL FOR TCM USING
SUBARU SELECT MONITOR.
1) Connect the connector to transmission.
2) Turn the ignition switch to ON (engine
OFF).
3) Read the data of ATF temperature using the
Subaru Select Monitor. 15, OPERATION, Subaru Select Monitor.>Does the ATF temperature
gradually decrease?Even if the POWER
indicator light was
blinking, the circuit
has returned to a
normal condition at
this time. Tempo-
rary poor contact of
the connector or
harness may be the
cause. Repair the
harness or contact
in ATF temperature
sensor and trans-
mission connector.Go to step 10.
10 CHECK POOR CONTACT.Is there poor contact in ATF
temperature sensor circuit?Repair the poor
contact.Replace the TCM.
Transmission Con-
trol Module
(TCM).>
11 CHECK HARNESS CONNECTOR BETWEEN
TRANSMISSION AND ATF TEMPERATURE
SENSOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from transmis-
sion.
3) Remove the transmission connector from
bracket.
4) Lift-up the vehicle and place rigid racks.
NOTE:
Raise all wheels off floor.
5) Drain the ATF.
CAUTION:
Do not drain the ATF until it cools down.
6) Remove the oil pan, and disconnect the
connector from ATF temperature sensor con-
nector.
7) Measure the resistance of harness
between ATF temperature sensor and trans-
mission connector.
Connector & terminal
(T4) No. 11 — (AT11) No. 1:Is the resistance less than 1
Ω?Go to step 12.Repair the open
circuit in harness
between ATF tem-
perature sensor
and transmission
connector.
12 CHECK HARNESS CONNECTOR BETWEEN
TRANSMISSION AND ATF TEMPERATURE
SENSOR.
Measure the resistance of harness between
ATF temperature sensor and transmission con-
nector.
Connector & terminal
(T4) No. 15 — (AT11) No. 3:Is the resistance less than 1
Ω?Go to step 13.Repair the open
circuit in harness
between ATF tem-
perature sensor
and transmission
connector.
13 CHECK HARNESS CONNECTOR BETWEEN
TRANSMISSION AND ATF TEMPERATURE
SENSOR.
Measure the resistance of harness between
transmission connector and transmission
ground.
Connector & terminal
(T4) No. 11 — Transmission ground:Is the resistance more than 1
MΩ?Go to step 14.Repair the short
circuit in harness
between ATF tem-
perature sensor
and transmission
connector. Step Check Yes No

Page 2621 of 2870

SUBARU FORESTER 2004 Service Repair Manual 4AT(H4DOTC)-45
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
14 CHECK HARNESS CONNECTOR BETWEEN
TRANSMISSION AND ATF TEMPERATURE
SENSOR.
Measure the res

Page 2622 of 2870

SUBARU FORESTER 2004 Service Repair Manual 4AT(H4DOTC)-46
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
C: DTC P0713 TRANSMISSION FLUID TEMPERATURE SENSOR CIRCUIT HIGH
INPUT
DTC DETECTING CONDITIO

Page 2623 of 2870

SUBARU FORESTER 2004 Service Repair Manual 4AT(H4DOTC)-47
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
2 CHECK HARNESS CONNECTOR BETWEEN
TCM AND ATF TEMPERATURE SENSOR.
Measure the voltage of har

4AT(H4DOTC)-47
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
2 CHECK HARNESS CONNECTOR BETWEEN
TCM AND ATF TEMPERATURE SENSOR.
Measure the voltage of harness between TCM
connector and chassis ground.
Connector & terminal
(B55) No. 9 (+) — Chassis ground (
−):Is the voltage less than 1 V? Go to step 3.Repair the short
circuit in harness
between TCM and
transmission con-
nector.
3 CHECK ATF TEMPERATURE SENSOR.
1) Turn the ignition switch to OFF.
2) Connect the connectors to transmission
and TCM.
3) Turn the ignition switch to ON and start
engine.
4) Warm-up the transmission until ATF tem-
perature reaches to 80°C (176°F).
N
OTE:
If ambient temperature is below 0°C (32°F),
drive the vehicle until ATF reaches its operating
temperature.
5) Disconnect the connector from transmis-
sion.
6) Measure the resistance between transmis-
sion connector terminals.
Connector & terminal
(T4) No. 11 — No. 15:Is the resistance 500 — 600
Ω?Go to step 4.Replace ATF tem-
perature sensor.
Control Valve
Body.>
4 CHECK ATF TEMPERATURE SENSOR.
Measure the resistance between transmission
connector terminals.
Connector & terminal
(T4) No. 11 — No. 15:Does the resistance value
increase when ATF tempera-
ture decreases? Go to step 5.Replace ATF tem-
perature sensor.
Control Valve
Body.>
5 PREPARE SUBARU SELECT MONITOR.Do you have a Subaru Select
Monitor?Go to step 7.Go to step 6.
6 CHECK INPUT SIGNAL FOR TCM.
1) Connect the connector to transmission.
2) Warm-up the transmission until ATF tem-
perature is about 80°C (176°F).
N
OTE:
If ambient temperature is below 0°C (32°F),
drive the vehicle until ATF reaches its operating
temperature.
3) Measure the voltage between TCM con-
nector terminal.
Connector & terminal
(B55) No. 9 (+) — No. 21 (
−):Is the voltage 1.5 — 1.9 V? Even if the POWER
indicator light was
blinking, the circuit
has returned to a
normal condition at
this time. Tempo-
rary poor contact of
the connector or
harness may be the
cause. Repair the
harness or contact
in ATF temperature
sensor and trans-
mission connector.Go to step 8.
7 CHECK INPUT SIGNAL FOR TCM USING
SUBARU SELECT MONITOR.
1) Connect the connector to transmission.
2) Turn the ignition switch to ON (engine
OFF).
3) Read the data of ATF temperature using
the Subaru Select Monitor. 4AT(H4DOTC)-15, OPERATION, Subaru
Select Monitor.>Does the ATF temperature
gradually decrease?Even if the POWER
indicator light was
blinking, the circuit
has returned to a
normal condition at
this time. Tempo-
rary poor contact of
the connector or
harness may be the
cause. Repair the
harness or contact
in ATF temperature
sensor and trans-
mission connector.Go to step 8. Step Check Yes No

Page 2624 of 2870

SUBARU FORESTER 2004 Service Repair Manual 4AT(H4DOTC)-48
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
8 CHECK POOR CONTACT.Is there poor contact in ATF
temperature sensor circuit?Repair the poor

Load next 8 pages

Page: < prev 1-10 ... 2585-2592 2593-2600 2601-2608 2609-2616 2617-2624 2625-2632 2633-2640 2641-2648 2649-2656 ... 2872 next >

technical data ground clearance gas mileage oil reset oil dipstick turn signal