Page 2185 of 2870

EN(H4DOTC 2.5)-161
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK CURRENT DATA.
1) Start the engine.
2) Read the data of exhaust temperature sen-
sor signal using Subaru Select Monitor or
OBD-II general scan tool.
N
OTE:
Subaru Select Monitor
For detailed operation procedure, refer to
“READ CURRENT DATA SHOWN ON DIS-
PLAY FOR ENGINE”.
2.5)-27, Subaru Select Monitor.>
OBD-II general scan tool
For detailed operation procedures, refer to the
OBD-II General Scan Tool Operation Manual.Is the temperature more than
1,200°C (2,192°F)?Go to step 2.Repair the poor
contact.
N
OTE:
In this case repair
the following:
Poor contact of
exhaust tempera-
ture sensor
Poor contact in
ECM
Poor contact in
joint connector
2 CHECK HARNESS BETWEEN EXHAUST
TEMPERATURE SENSOR AND ECM CON-
NECTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from exhaust
temperature sensor.
3) Turn the ignition switch to ON.
4) Read the data of exhaust temperature sen-
sor signal using Subaru Select Monitor or
OBD-II general scan tool.
N
OTE:
Subaru Select Monitor
For detailed operation procedure, refer to
“READ CURRENT DATA SHOWN ON DIS-
PLAY FOR ENGINE”.
2.5)-27, Subaru Select Monitor.>
OBD-II general scan tool
For detailed operation procedures, refer to the
OBD-II General Scan Tool Operation Manual.Is the temperature less than
372°C (702°F)?Replace the
exhaust tempera-
ture sensor.
to FU(H4DOTC
2.5)-40, Exhaust
Temperature Sen-
sor.>Repair ground
short circuit in har-
ness between
exhaust tempera-
ture sensor and
ECM connector.
Page 2186 of 2870
EN(H4DOTC 2.5)-162
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
AO:DTC P0546 EXHAUST GAS TEMPERATURE SENSOR HIGH - BANK 1
DTC DETECTING CONDITION:
Immediately at fault recognition
TROUBLE SYMPTOM:
Hard to start
Erroneous idling
Poor driving performance
CAUTION:
After repair or replacement of faulty parts, conduct Clear Memory Mode
OPERATION, Clear Memory Mode.> and Inspection Mode
Inspection Mode.>.
WIRING DIAGRAM:
EN-02369
B1226
B136 ECM
35 24
B2791
2
B279
112
B122
B136
56
782 1
94 310
24 22 23 2511 12 13
1415
26 27
2816
17 18 19 20 21
33 34 29
32 30
31 35
EXHAUST GAS
TEMPERATURE
SENSOR
12345678
Page 2187 of 2870

EN(H4DOTC 2.5)-163
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK CURRENT DATA.
1) Start the engine.
2) Read the data of exhaust temperature sen-
sor signal using Subaru Select Monitor or
OBD-II general scan tool.
N
OTE:
Subaru Select Monitor
For detailed operation procedure, refer to
“READ CURRENT DATA SHOWN ON DIS-
PLAY FOR ENGINE”.
2.5)-27, Subaru Select Monitor.>
OBD-II general scan tool
For detailed operation procedures, refer to the
OBD-II General Scan Tool Operation Manual.Is the temperature less than
372°C (702°F)?Go to step 2.Repair the poor
contact.
N
OTE:
In this case repair
the following:
Poor contact of
exhaust tempera-
ture sensor
Poor contact in
ECM
Poor contact in
joint connector
2 CHECK HARNESS BETWEEN EXHAUST
TEMPERATURE SENSOR AND ECM CON-
NECTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from exhaust
temperature sensor.
3) Measure the voltage between exhaust tem-
perature sensor connector and engine ground.
Connector & terminal
(B279) No. 1 (+) — Engine ground (
−):Is the voltage more than 10 V? Repair battery
short circuit in har-
ness between
ECM and exhaust
temperature sen-
sor connector.Go to step 3.
3 CHECK HARNESS BETWEEN EXHAUST
TEMPERATURE SENSOR AND ECM CON-
NECTOR.
1) Turn the ignition switch to ON.
2) Measure the voltage between exhaust tem-
perature sensor connector and engine ground.
Connector & terminal
(B279) No. 1 (+) — Engine ground (
−):Is the voltage more than 10 V? Repair battery
short circuit in har-
ness between
ECM and exhaust
temperature sen-
sor connector.Go to step 4.
4 CHECK HARNESS BETWEEN EXHAUST
TEMPERATURE SENSOR AND ECM CON-
NECTOR.
Measure the voltage between exhaust temper-
ature sensor connector and engine ground.
Connector & terminal
(B279) No. 1 (+) — Engine ground (
−):Is the voltage more than 4 V? Go to step 5.Repair the harness
and connector.
N
OTE:
In this case repair
the following:
Open circuit in
harness between
ECM and exhaust
temperature sen-
sor connector
Poor contact of
exhaust tempera-
ture sensor con-
nector
Poor contact in
ECM connector.
Poor contact in
joint connector
Page 2188 of 2870
EN(H4DOTC 2.5)-164
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
5 CHECK HARNESS BETWEEN EXHAUST
TEMPERATURE SENSOR AND ECM CON-
NECTOR.
1) Turn the ignition switch to OFF.
2) Measure the resistance of harness
between exhaust temperature sensor connec-
tor and engine ground.
Connector & terminal
(B279) No. 2 — Engine ground:Is the resistance less than 5
Ω?Replace the
exhaust tempera-
ture sensor.
to FU(H4DOTC
2.5)-40, Exhaust
Temperature Sen-
sor.>Repair the harness
and connector.
N
OTE:
In this case repair
the following:
Open circuit in
harness between
ECM and exhaust
temperature sen-
sor connector
Poor contact of
exhaust tempera-
ture sensor con-
nector
Poor contact in
ECM connector.
Poor contact in
joint connector Step Check Yes No
Page 2189 of 2870
EN(H4DOTC 2.5)-165
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
AP:DTC P0600 SERIAL COMMUNICATION LINK
DTC DETECTING CONDITION:
Immediately at fault recognition
CAUTION:
After repair or replacement of faulty parts, conduct Clear Memory Mode
OPERATION, Clear Memory Mode.> and Inspection Mode
Inspection Mode.>.
WIRING DIAGRAM:
AT-01524
18
263
12
B55
B137
ECM
B55 TCM
B137
12
7
8956 3410 11 12
19 20 2113 14 15 16
17 1822
23
24
567
82 1
94 310
22 23 11 12 13 14 15
24 25
2616 17
18 19 20 21
27 28 29 30 31
TWISTED WIRE
Page 2190 of 2870

EN(H4DOTC 2.5)-166
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK HARNESS BETWEEN ECM AND
TCM.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from ECM.
3) Disconnect the connectors from TCM.
4) Measure the resistance between ECM and
TCM connectors.
Connector & terminal
(B137) No. 18 — (B55) No. 3:
(B137) No. 26 — (B55) No. 12:Is the resistance less than 1
Ω?Go to step 2.Repair the harness
and connector.
2 CHECK HARNESS BETWEEN ECM AND
TCM.
Measure the resistance between ECM connec-
tor and chassis ground.
Connector & terminal
(B137) No. 18 — Chassis ground:
(B137) No. 26 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 3.Repair the harness
and connector.
3 CHECK HARNESS BETWEEN ECM AND
TCM.
Check the resistance between ECM connec-
tors.
Connector & terminal
(B137) No. 18 — (B137) No. 26:Is the resistance more than 1
MΩ?Go to step 4.Repair the harness
and connector.
4 CHECK AT SYSTEM CONDITION.
Perform the diagnosis for AT using Subaru
Select Monitor.Is DTC P1718 displayed? Check AT system. Replace the ECM.
Page 2191 of 2870
EN(H4DOTC 2.5)-167
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
AQ:DTC P0604 INTERNAL CONTROL MODULE READ ACCESS MEMORY
(RAM) ERROR
DTC DETECTING CONDITION:
Immediately at fault recognition
TROUBLE SYMPTOM:
Engine does not start.
Engine stalls.
CAUTION:
After repair or replacement of faulty parts, conduct Clear Memory Mode
OPERATION, Clear Memory Mode.> and Inspection Mode
Inspection Mode.>.
Page 2192 of 2870
EN(H4DOTC 2.5)-168
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
WIRING DIAGRAM:
Step Check Yes No
1 CHECK ANY OTHER DTC ON DISPLAY.Does the Subaru Select Moni-
tor or OBD-II general scan tool
indicate DTC P0604?Replace the ECM.
FU(H4DOTC 2.5)-
41, Engine Con-
trol Module
(ECM).>Temporary poor
contact occurs.
EN-02356
B72
B135
3412
BATTERY MAIN RELAY
SBF-4 SBF-1SBF-5
B72
D16 D7
B12
A6
A7
B1
B4
D1
D2
A34B5
B6
B19
D14
No.11
B47
E2 B21 1 2 3 5 6 4
ECM
E
E
1 4
B134
B135
B137 A:
B:
D:
14133
15
16
34 12
56123
4
56
78
91011 12
1314 15 16
B134 B21 B47B137 A: D:
B: IGNITION
SWITCH
56 7
82 1
94 310
24 22 23 25 11 12 13 14 15
26 27
2816 17
18 19 20 21
33 34 29
32 30 31
567
82 1
94 310
24 22 23 2511 12 13 14 15
26 27
2816 17 18 19
20 21
29 30 31 32 33 34 35
567
82 1
94 310
22 23 11 12 13 14 15
24 25
2616 17
18 19 20 21
27 28 29 30 31