2004 SUBARU FORESTER Service Repair Manual

fuse box diagram center console USB bulb fuse diagram airbag disable

Page 1305 of 2870

SUBARU FORESTER 2004 Service Repair Manual EN(H4SO)-207
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK OPERATION OF BRAKE LIGHT.Does the brake light come on
when depressing the brake
ped

EN(H4SO)-207
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK OPERATION OF BRAKE LIGHT.Does the brake light come on
when depressing the brake
pedal?Go to step 2.Repair or replace
the brake light cir-
cuit.
2 CHECK HARNESS BETWEEN TCM AND
BRAKE LIGHT SWITCH CONNECTOR.
1) Disconnect the connectors from TCM and
brake light switch.
2) Measure the resistance of harness
between TCM and brake light switch connec-
tor.
Connector & terminal
WITHOUT CRUISE CONTROL
(B55) No. 12 — (B64) No. 2:
WITH CRUISE CONTROL
(B55) No. 12 — (B65) No. 3:Is the resistance less than 1
Ω?Go to step 3.Repair or replace
the harness and
connector.
N
OTE:
In this case repair
the following:
Open circuit in
harness between
TCM and brake
light switch con-
nector
Poor contact in
TCM connector
Poor contact in
brake light switch
connector
3 CHECK HARNESS BETWEEN TCM AND
BRAKE LIGHT SWITCH CONNECTOR.
Measure the resistance of harness between
TCM and chassis ground.
Connector & terminal
(B55) No. 12 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 4.Repair ground
short circuit in har-
ness between
TCM and brake
light switch con-
nector.
4 CHECK INPUT SIGNAL FOR TCM.
1) Connect the connectors to TCM and brake
light switch.
2) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B55) No. 12 (+) — Chassis ground (
−):Is the voltage less than 1 V
when releasing the brake
pedal?Go to step 5.Adjust or replace
the brake light
switch. 8, STOP LIGHT
SWITCH,
INSPECTION,
Stop Light Sys-
tem.>
5 CHECK INPUT SIGNAL FOR TCM.
Measure the voltage between TCM and chas-
sis ground.
Connector & terminal
(B55) No. 12 (+) — Chassis ground (
−):Is the voltage more than 10 V
when depressing the brake
pedal?Go to step 6.Adjust or replace
the brake light
switch. 8, STOP LIGHT
SWITCH,
INSPECTION,
Stop Light Sys-
tem.>
6 CHECK POOR CONTACT.
Check poor contact in TCM connector.Is there poor contact in TCM
connector?Repair poor con-
tact in TCM con-
nector.Replace the TCM.
Transmission Con-
trol Module
(TCM).>

Page 1306 of 2870

SUBARU FORESTER 2004 Service Repair Manual EN(H4SO)-208
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
BG:DTC P0731 GEAR 1 INCORRECT RATIO
NOTE:
For the diagnostic procedure, refer to DTC P0734. <Ref. to EN(H4SO)-2

Page 1307 of 2870

SUBARU FORESTER 2004 Service Repair Manual EN(H4SO)-209
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
BJ:DTC P0734 GEAR 4 INCORRECT RATIO
DTC DETECTING CONDITION:
Two consecutive driving cycles with fault
TROUBLE

EN(H4SO)-209
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
BJ:DTC P0734 GEAR 4 INCORRECT RATIO
DTC DETECTING CONDITION:
Two consecutive driving cycles with fault
TROUBLE SYMPTOM:
Shift point too high or too low.
Engine brake not effected in 3rd range.
Excessive shift shock.
Excessive tight corner braking.
CAUTION:
After repair or replacement of faulty parts, conduct Clear Memory Mode ERATION, Clear Memory Mode.> and Inspection Mode tion Mode.>.
Step Check Yes No
1 CHECK ANY OTHER DTC ON DISPLAY.Is any other DTC displayed? Inspect the rele-
vant DTC using
“List of Diagnostic
Trouble Code
(DTC)”. EN(H4SO)-72, List
of Diagnostic Trou-
ble Code (DTC).>Go to step 2.
2 CHECK THROTTLE POSITION SENSOR
CIRCUIT.
Check the throttle position sensor circuit. to 4AT(H4SO)-41, DTC 31 THROTTLE POSI-
TION SENSOR, Diagnostic Procedure with
Diagnostic Trouble Code (DTC).>Is there any trouble in throttle
position sensor circuit?Repair or replace
the throttle posi-
tion sensor circuit.Go to step 3.
3 CHECK FRONT VEHICLE SPEED SENSOR
CIRCUIT.
Check front vehicle speed sensor circuit. to 4AT(H4SO)-45, DTC 33 FRONT VEHICLE
SPEED SENSOR, Diagnostic Procedure with
Diagnostic Trouble Code (DTC).>Is there any trouble in front
vehicle speed sensor circuit?Repair or replace
the front vehicle
speed sensor cir-
cuit.Go to step 4.
4 CHECK TORQUE CONVERTER TURBINE
SPEED SENSOR CIRCUIT.
Check torque converter turbine speed sensor
circuit. TORQUE CONVERTER TURBINE SPEED
SENSOR, Diagnostic Procedure with Diagnos-
tic Trouble Code (DTC).>Is there any trouble in torque
converter turbine speed sensor
circuit?Repair or replace
the torque con-
ver ter turbine
speed sensor cir-
cuit.Go to step 5.
5 CHECK POOR CONTACT.
Check poor contact in TCM connector.Is there poor contact in TCM
connector?Repair poor con-
tact in TCM con-
nector.Go to step 6.
6 CHECK MECHANICAL TROUBLE.
Check mechanical trouble in automatic trans-
mission.Is there any mechanical trou-
ble in automatic transmission?Repair or replace
the automatic
transmission.
INSPECTION,
Road Test.>Replace the TCM.
Transmission Con-
trol Module
(TCM).>

Page 1308 of 2870

SUBARU FORESTER 2004 Service Repair Manual EN(H4SO)-210
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
BK:DTC P0741 TORQUE CONVERTER CLUTCH CIRCUIT PERFORMANCE OR
STUCK OFF
DTC DETECTING CONDITION:
Two consecutive

EN(H4SO)-210
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
BK:DTC P0741 TORQUE CONVERTER CLUTCH CIRCUIT PERFORMANCE OR
STUCK OFF
DTC DETECTING CONDITION:
Two consecutive driving cycles with fault
TROUBLE SYMPTOM:
No lock-up (after engine warm-up)
No shift or excessive tight corner “braking”
CAUTION:
After repair or replacement of faulty parts, conduct Clear Memory Mode ERATION, Clear Memory Mode.> and Inspection Mode tion Mode.>.
Step Check Yes No
1 CHECK ANY OTHER DTC ON DISPLAY.Is any other DTC displayed? Inspect the rele-
vant DTC using
“List of Diagnostic
Trouble Code
(DTC)”. EN(H4SO)-72, List
of Diagnostic Trou-
ble Code (DTC).>Go to step 2.
2 CHECK LOCK-UP DUTY SOLENOID CIR-
CUIT.
Check lock-up duty solenoid circuit. 4AT(H4SO)-74, DTC 77 LOCK-UP DUTY
SOLENOID, Diagnostic Procedure with Diag-
nostic Trouble Code (DTC).>Is there any trouble in lock-up
duty solenoid circuit?Repair or replace
the lock-up duty
solenoid circuit.Go to step 3.
3 CHECK THROTTLE POSITION SENSOR
CIRCUIT.
Check the throttle position sensor circuit. to 4AT(H4SO)-41, DTC 31 THROTTLE POSI-
TION SENSOR, Diagnostic Procedure with
Diagnostic Trouble Code (DTC).>Is there any trouble in throttle
position sensor circuit?Repair or replace
the throttle posi-
tion sensor circuit.Go to step 4.
4 CHECK TORQUE CONVERTER TURBINE
SPEED SENSOR CIRCUIT.
Check torque converter turbine speed sensor
circuit. TORQUE CONVERTER TURBINE SPEED
SENSOR, Diagnostic Procedure with Diagnos-
tic Trouble Code (DTC).>Is there any trouble in torque
converter turbine speed sensor
circuit?Repair or replace
the torque con-
ver ter turbine
speed sensor cir-
cuit.Go to step 5.
5 CHECK ENGINE SPEED INPUT CIRCUIT.
Check engine speed input circuit. 4AT(H4SO)-36, DTC 11 ENGINE SPEED SIG-
NAL, Diagnostic Procedure with Diagnostic
Trouble Code (DTC).>Is there any trouble in engine
speed input circuit?Repair or replace
the engine speed
input circuit.Go to step 6.
6 CHECK INHIBITOR SWITCH CIRCUIT.
Check inhibitor switch circuit. 4AT(H4SO)-95, CHECK INHIBITOR SWITCH,
Diagnostic Procedure without Diagnostic Trou-
ble Code (DTC).>Is there any trouble in inhibitor
switch circuit?Repair or replace
the inhibitor switch
circuit.Go to step 7.
7 CHECK BRAKE LIGHT SWITCH CIRCUIT.
Check brake light switch circuit. 4AT(H4SO)-88, CHECK BRAKE SWITCH,
Diagnostic Procedure without Diagnostic Trou-
ble Code (DTC).>Is there any trouble in brake
light switch circuit?Repair or replace
the brake light
switch circuit.Go to step 8.

Page 1309 of 2870

SUBARU FORESTER 2004 Service Repair Manual EN(H4SO)-211
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
8 CHECK ATF TEMPERATURE SENSOR CIR-
CUIT.
Check ATF temperature sensor circuit. <Ref. to
4AT(H4SO)-38, DTC 27

Page 1310 of 2870

SUBARU FORESTER 2004 Service Repair Manual EN(H4SO)-212
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
BL:DTC P0851 NEUTRAL SWITCH INPUT CIRCUIT LOW
DTC DETECTING CONDITION:
Two consecutive driving cycles with faul

Page 1311 of 2870

SUBARU FORESTER 2004 Service Repair Manual EN(H4SO)-213
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK ANY OTHER DTC ON DISPLAY.Is DTC P0705 displayed? Inspect the DTC
using “List of Di

EN(H4SO)-213
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK ANY OTHER DTC ON DISPLAY.Is DTC P0705 displayed? Inspect the DTC
using “List of Diag-
nostic Trouble
Code (DTC)”.
EN(H4SO)-72, List
of Diagnostic Trou-
ble Code (DTC).>Go to step 2.
2 CHECK INPUT SIGNAL FROM ECM.
1) Turn the ignition switch to ON.
2) Shift the select lever to other than “N” and
“P” ranges.
3) Measure the voltage between ECM and
chassis ground.
Connector & terminal
(B136) No. 21 (+) — Chassis ground (
−):Is the voltage more than 10 V? Even if the mal-
function indicator
light illuminates,
the circuit has
returned to a nor-
mal condition at
this time.Go to step 3.
3 CHECK HARNESS BETWEEN ECM AND
TRANSMISSION HARNESS CONNECTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from ECM and
transmission harness connector (T3).
3) Measure the resistance of harness
between ECM connector and chassis ground.
Connector & terminal
(B136) No. 21 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 4.Repair ground
short circuit in har-
ness between
ECM and trans-
mission harness
connector.
4 CHECK TRANSMISSION HARNESS CON-
NECTOR.
1) Disconnect the connector from inhibitor
switch.
2) Measure the resistance of harness
between transmission harness connector and
engine ground.
Connector & terminal
(T3) No. 12 — Engine ground:Is the resistance more than 1
MΩ?Go to step 5.Repair ground
short circuit in har-
ness between
transmission har-
ness and inhibitor
switch connector.
5 CHECK INHIBITOR SWITCH.
Measure the resistance between inhibitor
switch connector receptacle’s terminals with
select lever at other than “N” and “P” range.
Te r m i n a l s
No. 7 — No. 12:Is the resistance more than 1
MΩ?Go to step 6.Replace inhibitor
switch. 4AT-51, Inhibitor
Switch.>
6 CHECK SELECTOR CABLE CONNECTION.Is there any fault in selector
cable connection to inhibitor
switch?Repair the select
cable connection.
INSPECTION,
Select Cable.>Contact the SUB-
ARU dealer.
N
OTE:
Inspection by DTM
is required, because
probable cause is
deterioration of mul-
tiple parts.

Page 1312 of 2870

SUBARU FORESTER 2004 Service Repair Manual EN(H4SO)-214
ENGINE (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
BM:DTC P0851 NEUTRAL SWITCH INPUT CIRCUIT LOW (MT MODEL)
DTC DETECTING CONDITION:
Two consecutive driving cycl

Load next 8 pages

Page: < prev 1-10 ... 1273-1280 1281-1288 1289-1296 1297-1304 1305-1312 1313-1320 1321-1328 1329-1336 1337-1344 ... 2872 next >

child seat bulb turn signal bulb fuel filter homelink traction control