2004 SUBARU FORESTER Service Repair Manual

auxiliary battery location check engine light OBD port wiring relay jump start

Page 2665 of 2870

SUBARU FORESTER 2004 Service Repair Manual 4AT(H4DOTC)-89
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK IGNITION POWER SUPPLY CIR-
CUIT.
1) Turn the ignition switch to OFF

4AT(H4DOTC)-89
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK IGNITION POWER SUPPLY CIR-
CUIT.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from rear vehicle
speed sensor.
3) Turn the ignition switch to ON.
4) Measure the ignition power supply voltage
between rear vehicle speed sensor connector
and transmission ground.
Connector & terminal
(AT10) No. 3 (+) — Transmission ground
(
−):Is the voltage more than 10 V? Go to step 2.Check harness
between rear vehi-
cle speed sensor
and battery for
open circuit, short
or poor contact.
Repair the har-
ness if required.
2 CHECK HARNESS CONNECTOR BETWEEN
TCM AND REAR VEHICLE SPEED SENSOR.
1) Turn the ignition switch to OFF.
2) Measure the resistance of harness between
TCM and rear vehicle speed sensor connector.
Connector & terminal
(B55) No. 23 — (AT10) No. 1:Is the resistance less than 1
Ω?Go to step 3.Repair the open
circuit or poor con-
tact of connector in
harness between
TCM and rear
vehicle speed sen-
sor connector.
3 CHECK HARNESS CONNECTOR BETWEEN
TCM AND REAR VEHICLE SPEED SENSOR.
Measure the resistance of harness between
TCM and rear vehicle speed sensor connector.
Connector & terminal
(B55) No. 24 — (AT10) No. 2:Is the resistance less than 1
Ω?Go to step 4.Repair the open
circuit or poor con-
tact of connector in
harness between
TCM and rear
vehicle speed sen-
sor connector.
4 CHECK HARNESS CONNECTOR BETWEEN
TCM AND TRANSMISSION.
Measure the resistance of harness between
TCM connector and chassis ground.
Connector & terminal
(B55) No. 23 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 5.Repair the short
circuit in harness
between TCM and
rear vehicle speed
sensor connector.
5 CHECK HARNESS CONNECTOR BETWEEN
TCM AND TRANSMISSION.
Measure the resistance of harness between
TCM connector and chassis ground.
Connector & terminal
(B55) No. 24 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 6.Repair the short
circuit in harness
between TCM and
rear vehicle speed
sensor connector.
6 CHECK OUTPUT SIGNAL FROM TCM.
1) Connect the connector to TCM.
2) Turn the ignition switch to ON.
3) Measure the voltage between transmission
connector terminals.
Connector & terminal
(B55) No. 24 (+) — No. 24 (
−):Is the voltage approx. 5 V? Go to step 7.Go to step 10.
7 PREPARE OSCILLOSCOPE.Do you have an oscilloscope? Go to step 9.Go to step 8.

Page 2666 of 2870

SUBARU FORESTER 2004 Service Repair Manual 4AT(H4DOTC)-90
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
8 CHECK INPUT SIGNAL FOR TCM.
1) Connect the connectors to TCM and trans-
mission.
2) Lift-up

Page 2667 of 2870

SUBARU FORESTER 2004 Service Repair Manual 4AT(H4DOTC)-91
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
W: DTC P1707 AT AWD SOLENOID VALVE CIRCUIT MALFUNCTION
DTC DETECTING CONDITION:
Output signal

Page 2668 of 2870

SUBARU FORESTER 2004 Service Repair Manual 4AT(H4DOTC)-92
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
5 CHECK OUTPUT SIGNAL FROM TCM.
1) Connect the connectors to TCM and trans-
mission.
2) Turn

4AT(H4DOTC)-92
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
5 CHECK OUTPUT SIGNAL FROM TCM.
1) Connect the connectors to TCM and trans-
mission.
2) Turn the ignition switch to ON (engine OFF).
3) Shift the select lever to “P” range.
4) Throttle is fully closed.
5) Measure the voltage between TCM con-
nector and chassis ground.
Connector & terminal
(B56) No. 4 (+) — Chassis ground (
−):Is the voltage less than 1 V? Go to step 6.Go to step 9.
6 CHECK OUTPUT SIGNAL FROM TCM.
1) Shift the select lever to “D” range.
2) Measure the voltage between TCM con-
nector and chassis ground with throttle fully
open.
Connector & terminal
(B56) No. 4 (+) — Chassis ground (
−):Is the voltage more than 10.5
V?Even if the POWER
indicator light was
blinking, the circuit
has returned to a
normal condition at
this time. A tempo-
rary poor contact of
the connector or
harness may be the
cause. Repair the
harness or connec-
tor in TCM and
transmission.Go to step 9.
7 CHECK OUTPUT SIGNAL FROM TCM US-
ING SUBARU SELECT MONITOR.
1) Connect the connectors to TCM and trans-
mission.
2) Connect the Subaru Select Monitor to data
link connector.
3) Turn the ignition switch to ON (engine OFF)
and turn Subaru Select Monitor switch to ON.
4) Move the select lever to “N” range with
throttle fully close (vehicle speed 0 km/h (0
MPH)).
5) Read data of transfer duty solenoid using
Subaru Select Monitor.
Transfer duty solenoid is indicated in “%”.Is the value 5%? Go to step 8.Go to step 9.
8 CHECK OUTPUT SIGNAL EMITTED FROM
TCM USING SUBARU SELECT MONITOR.
1) Shift the select lever to “D” range with throt-
tle fully open (vehicle speed 0 km/h (0 MPH)).
2) Read the data of transfer duty solenoid
using Subaru Select Monitor.
Transfer duty solenoid is indicated in “%”.Is the value 90 — 95%? Even if the POWER
indicator light was
blinking, the circuit
has returned to a
normal condition at
this time. A tempo-
rary poor contact of
the connector or
harness may be the
cause. Repair the
harness or connec-
tor in TCM and
transmission.Go to step 9.
9 CHECK POOR CONTACT.Is there poor contact in transfer
duty solenoid circuit?Repair the poor
contact.Replace the TCM.
Transmission Con-
trol Module
(TCM).> Step Check Yes No

Page 2669 of 2870

SUBARU FORESTER 2004 Service Repair Manual 4AT(H4DOTC)-93
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
10 CHECK TRANSFER DUTY SOLENOID (IN
TRANSMISSION).
1) Lift-up the vehicle and place rigid ra

Page 2670 of 2870

SUBARU FORESTER 2004 Service Repair Manual 4AT(H4DOTC)-94
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
X: DTC P1708 THROTTLE POSITION SENSOR CIRCUIT LOW INPUT
DTC DETECTING CONDITION:
Input sign

Page 2671 of 2870

SUBARU FORESTER 2004 Service Repair Manual 4AT(H4DOTC)-95
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
WIRING DIAGRAM:
LHD model
AT-01851
E13
B122
F60
B134B55 TCM
A:B135 B:ECMB136 C:B137 D:
E3
B

Page 2672 of 2870

SUBARU FORESTER 2004 Service Repair Manual 4AT(H4DOTC)-96
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
RHD model
Step Check Yes No
1 CHECK ENGINE GROUND TERMINALS.Have engine ground terminals
b

Load next 8 pages

Page: < prev 1-10 ... 2633-2640 2641-2648 2649-2656 2657-2664 2665-2672 2673-2680 2681-2688 2689-2696 2697-2704 ... 2872 next >

tires sat nav wiper size service interval fuses garage door opener