Page 1801 of 2234
\b\b\bB69320
Sedan Models
Liftback Models
Wagon ModelsSlit
Slit
Strap
Strap
Strap
Slit
76±16
±
EXTERIOR/INTERIOR TRIM FUEL LID LOCK CONTROL ASSY
AVENSIS REPAIR MANUAL (RM1018E)
(b) Pass the strap through the slit on the trim as shown in the illustration.
(c) Attach a strap to the trim.
http://vnx.su
Page 1802 of 2234
760W9±01
B67626
NutClip
±
EXTERIOR/INTERIOR TRIMLUGGAGE COMPARTMENT DOOR GARNISH
SUB±ASSY OUTSIDE(SEDAN MODELS)76±27
AVENSIS REPAIR MANUAL (RM1018E)
LUGGAGE COMPARTMENT DOOR GARNISH SUB±ASSY
OUTSIDE(SEDAN MODELS)
REPLACEMENT
HINT:
The installation is in the reverse order of the removal. However, when there is a special point concerning
the installation, it is indicated.
1.REMOVE BACK DOOR TRIM COVER (See page 75±32)
2. REMOVE LUGGAGE COMPARTMENT DOOR GARNISH SUB±ASSY OUTSIDE
(a) Remove the 6 nuts, clip and garnish.
3. INSTALL BACK DOOR GARNISH SUB±ASSY OUTSIDE
(a) Install the garnish with the 6 nuts and clip.
Torque: 4.9 N m (50 kgf cm, 43 in. lbf)
http://vnx.su
Page 1803 of 2234
760W4±01
B67148
110.1 (4.335)
57.3 (2.256)
39.1 (1.717) 120.9 (4.760)43.6 (1.717)
39.1 (1.539)
106.8 (4.205)
53.9 (2.122)
39.7 (1.563) 101.5 (3.996)
39.6 (1.559)24.4 (0.961)
mm (in.)
1
1
RH Side1
RH Side
1
LH Side1
LH Side
±
EXTERIOR/INTERIOR TRIM NAME PLATE
76±17
AVENSIS REPAIR MANUAL (RM1018E)
NAME PLATE
REPLACEMENT
http://vnx.su
Page 1804 of 2234
B67145
59.0 (2.323)20.3 (0.799)
131.2 (5.165) 91.1 (3.587)
115.4 (4.543)
161.3 (6.350)14.6 (0.575)47.1 (1.854)
63.5 (2.450) 26.6 (1.047)
97.1 (3.823)
49 (1.929)
mm (in.)
1
2
3
12
3
Sedan Models
76±18
±
EXTERIOR/INTERIOR TRIM NAME PLATE
AVENSIS REPAIR MANUAL (RM1018E)
http://vnx.su
Page 1805 of 2234
B67146
59.3 (2.335)20.5 (0.807)
131.2 (5.165)88.6 (3.488)
89 (3.504) 161.1 (6.342)
14.7 (0.579)
47.1 (1.854)
61.3 (2.41)
97.3 (3.831)
27 (1.063)
48.2 (1.898)2
3
2
3
Liftback Models
1
1
mm (in.)
±
EXTERIOR/INTERIOR TRIM NAME PLATE
76±19
AVENSIS REPAIR MANUAL (RM1018E)
http://vnx.su
Page 1806 of 2234
B67147
129.7 (5.106)52.5 (2.067)
162 (6.378)144.5 (5.689)
115.4 (4.543) 109.6 (4.315)38.1 (1.500)95.5 (3.760)
115.4 (4.543)
40 (1.575)
109.6 (4.315)
97 (3.819) 2
3
1
12
3
Wagon Models
mm (in.)
76±20
±
EXTERIOR/INTERIOR TRIM NAME PLATE
AVENSIS REPAIR MANUAL (RM1018E)
http://vnx.su
Page 1807 of 2234

760W5±01
B50319
Protective
Tape
B67149
Double±sided Tape
±
EXTERIOR/INTERIOR TRIM OUTSIDE MOULDING LH
76±21
AVENSIS REPAIR MANUAL (RM1018E)
OUTSIDE MOULDING LH
REPLACEMENT
HINT:
On the RH side, use the same procedures as on the LH side.
1. REMOVE OUTSIDE MOULDING LH
(a) Using a heat light, heat the moulding.Heating temprature: 40 ± 60 C (104 ± 140 F)
NOTICE:
Do not heat the moulding excessively.
(b) Tie both the piano wire ends to a wooden block or a similar object.
(c) Scrape tape off by pulling the piano wire and remove the moulding with reference pins remaining on the moulding.
NOTICE:
If reusing the moulding, take care not to damage the
moulding.
Do not damage the body.
(d) Remove the moulding.
2. INSTALL OUTSIDE MOULDING LH
(a) Using a heat light, heat the body surface. Heating temprature: 40 ± 60 C (104 ± 140 F)
NOTICE:
Do not heat the body excessively.
(b) Remove the tape from the body.
(c) Wipe off the stains with cleaner.
(d) Clean the moulding (if reusing the moulding).
(1) Using a heat light, heat the moulding.
Heating temprature: 20 ± 30 C (68 ± 86 F)
NOTICE:
Do not heat the moulding excessively. (2) Remove the tape from the moulding.
(3) Wipe off the stains with cleaner.
(4) Apply new double±sided tape to the moulding as
shown in the illustration.
http://vnx.su
Page 1808 of 2234
B67150mm (in.)
16.2 (0.638)
28 (1.102)
228.7 (9.004)243 (9.567) 243 (9.567)
2.3 (0.091)
3.8 (0.150)
252.7 (9.949)
119 (4.685)
16.4 (0.646)
76±22
±
EXTERIOR/INTERIOR TRIM OUTSIDE MOULDING LH
AVENSIS REPAIR MANUAL (RM1018E)
(e) Using a heat light, heat the body and moulding. Heating temperature:
Body40 ± 60 C (104 ± 140 F)
Moulding20 ± 30C (68 ± 86 F)
NOTICE:
Do not heat the body and moulding excessively.
(f) Remove the peeling paper from the face of the moulding
and attach the moulding securely to the vehicle body.
NOTICE:
Be careful that dirt or foreign objects do not stick to adhe-
sive part when removeing the peeling paper.
(g) Push the moulding to the body, as shown in the illustra- tion.
NOTICE:
Do not apply excessive force onto the moulding. Instead,
apply steady pressure with your thumbs.
http://vnx.su