Page 3161 of 4087
RS±58
RS±59
RS±63RS±65
RS±67
RS±68
RS±63
RS±59
RS±59
RS±59
±
SUPPLEMENTAL RESTRAINT SYSTEM TROUBLESHOOTINGRS±57
WhereEverybodyKnowsYourName
Page 3162 of 4087
Page 3163 of 4087

SRS WARNING LIGHT CHECK
DIAGNOSIS INSPECTION
(a) Turn the ignition switch to ACC or ON and check that the SRSwarning light lights up.
(b) Check that the SRS warning light goes out after approx. 6
seconds.
HINT:
wWhen the ignition switch is at ACC or ON and the SRS
warning light remains on, the TROUBLESHOOTING
has detected a malfunction code.
w If, after approx. 6 seconds have elapsed, the SRS
warning light sometimes lights up or the SRS warning
light lights up even when the ignition switch is OFF, a
short in the SRS warning light circuit can be considered
likely. Proceed to SRS warning light system (always lit
up when ignition switch LOCK position) on page
RS±119 .
DIAGNOSTIC TROUBLE CODE CHECK
Using diagnosis check wire:
1. OUTPUT DIAGNOSTIC TROUBLE CODE
(a) Turn the ignition switch to ACC or ON position and wait approx. 20 seconds.
(b) Using SST, connect terminals Tc and E of the DLC2. SST 09843±18020
NOTICE: Never make a mistake with the terminal connec-
tion position as this will cause a malfunction.
±
SUPPLEMENTAL RESTRAINT SYSTEM TROUBLESHOOTINGRS±59
WhereEverybodyKnowsYourName
Page 3164 of 4087

2. READ DIAGNOSTIC TROUBLE CODERead the 2±digit diagnostic trouble code as indicated by the
number of times the SRS warning light blinks. As an example,
the blinking patterns; normal, 11 and 31 are as shown on the
illustration.
wNormal code indication
The light will blink 2 times per second.
w Malfunction code indication
In the event of a malfunction, the light will blink. The number
represented by the first blink code output indicates the first
digit of a 2±digit diagnostic trouble code. After a 1.5 second
pause, the second blink code will indicate the second digit.
If there are two or more codes, there will be a 2.5 second
pause between each.
After all the codes have been output, there will be a 4.0 se-
cond pause and they will all be repeated.
HINT:
w In the event of a number of trouble codes, indication will
begin from the smaller numbered code to the larger.
w If it does not output a diagnostic trouble code or output
a diagnostic trouble code without terminal connection,
proceed to the Tc terminal circuit inspection on page
RS±121 .
Using LEXUS hand±held tester: (a) Hook up the LEXUS hand±held tester to the DLC1 or DLC2.
(b) Read the diagnostic trouble codes by following the prompts on the tester screen.
HINT: Please refer to the LEXUS hand±held tester operator's
manual for further details.
RS±60
±
SUPPLEMENTAL RESTRAINT SYSTEM TROUBLESHOOTING
WhereEverybodyKnowsYourName
Page 3165 of 4087
DIAGNOSTIC TROUBLE CODES
±
SUPPLEMENTAL RESTRAINT SYSTEM TROUBLESHOOTINGRS±61
WhereEverybodyKnowsYourName
Page 3166 of 4087
HINT:
When the SRS warning light remains lit up and the diagnostic trouble code in\
the normal code, this means a
source voltage drop.
This malfunction is not stored in memory by the center airbag sensor assembl\
y and if the power source voltage
returns to normal, after approx. 10 seconds the SRS warning light will automati\
cally go out.
Code 22 in recorded when a malfunction occurs in the SRS warning light syste\
m. If an open malfunction occurs
in the SRS warning light system, the SRS warning light does not light up\
. so that until the malfunction is repaired,
the diagnostic trouble codes (including code 22) cannot be confirmed.
When 2 or more codes are indicated, the lowest numbered code will appear\
first.
If a code not listed on the chart is displayed, then the center airbag s\
ensor assembly is faulty.
RS±62
±
SUPPLEMENTAL RESTRAINT SYSTEM TROUBLESHOOTING
WhereEverybodyKnowsYourName
Page 3167 of 4087
DIAGNOSTIC TROUBLE CODE
CLEARANCE
Using diagnostic check wire:(a) Connect the 2 service wires to terminals Tc and AB of DLC1.
(b) Turn the ignition switch ACC or ON And wait approx. 6 seconds.
(c) Starting with the Tc terminal, apply body ground alternately to terminal Tc and terminal AB twice each in cycles of 1.0
seconds Confirm that body ground is absolute. Finally, keep
applying body ground to terminal Tc.
HINT: When alternately grounding terminals Tc and AB, re-
lease ground from one terminal and immediately apply it to
the other terminal within an interval of 0.2 second. If diagnos-
tic trouble codes do not clear, repeat the above procedure un-
til the codes are cleared.
(d) Several seconds after performing the clearing procedure, theSRS warning light will blink in a 50 m sec cycle to indicate the
codes have been cleared.
±
SUPPLEMENTAL RESTRAINT SYSTEM TROUBLESHOOTINGRS±63
WhereEverybodyKnowsYourName
Page 3168 of 4087
Using LEXUS hand±held tester:(a) Hook up the LEXUS hand±held tester to the DLC1 or DLC2.
(b) Clear the diagnostic trouble codes by following the prompts on the tester screen.
HINT: Please refer to the LEXUS hand±held tester operator's
manual for further details.
RS±64
±
SUPPLEMENTAL RESTRAINT SYSTEM TROUBLESHOOTING
WhereEverybodyKnowsYourName