Page 3137 of 4087
8. INSTALL FOLLOWING PARTS:
(a) Glove compartment door lock mounting bracket
(b) Glove compartment assemblyNOTICE: When installing the glove compartment assem-
bly, carefully pull out the airbag wire harness from the
glove compartment upper hole.
(c) Airbag connector
(d) Glove compartment door finish plate
(e) No.2 instrument panel under cover
9. CONNECT NEGATIVE (±) TERMINAL CABLE TO BATTERY
±
SUPPLEMENTAL RESTRAINT SYSTEM FRONT PASSENGER AIRBAG ASSEMBLYRS±33
WhereEverybodyKnowsYourName
Page 3138 of 4087

FRONT PASSENGER AIRBAG
ASSEMBLY DISPOSAL
RS01P±02
When scrapping vehicles equipped with an supplemental re-
straint system or disposing of a front passenger airbag as-
sembly, always first deploy the airbag in accordance with the
procedure described below.
If any abnormality occurs with the airbag deployment, con-
tact the SERVICE DEPT. of TOYOTA MOTOR SALES,
U.S.A., INC..
Never dispose of a front passenger airbag assembly
which has an undeployed airbag.
When disposing of a front passenger airbag assembly with
an airbag deployed in a collision, follow the same procedure
given under ªWhen scrapping vehicle, step 5. DISPOSAL OF
FRONT PASSENGER AIRBAG ASSEMBLYº (See page
RS±36 ).
PRECAUTIONS FOR AIRBAG DEPLOYMENT
w The airbag produces a sizeable exploding sound when
it deploys, so perform the operation out±of±doors and
where it will not create a nuisance to nearby residents.
w When deploying the airbag, always use the specified
SST: SRS AIRBAG DEPLOYMENT TOOL (SST
09082±00700). Perform the operation in a place away
from electrical noise.
w When deploying an airbag, perform the operation from
at least 10 m (33 ft) away from the front passenger
airbag assembly.
w The front passenger airbag assembly is very hot when
the airbag is deployed, so leave it alone for at least 30
minutes after deployment.
w Use gloves and safety glasses when handling a front
passenger airbag assembly with deployed airbag.
w Always wash your hands with water after completing the
operation.
w Do not apply water, etc., to a front passenger airbag
assembly deployed airbag.
RS±34
±
SUPPLEMENTAL RESTRAINT SYSTEM FRONT PASSENGER AIRBAG ASSEMBLY
WhereEverybodyKnowsYourName
Page 3139 of 4087

When scrapping vehicle
HINT: Have a battery ready as the power source to deploy the
airbag.
1. DISCONNECT NEGATIVE (±) TERMINAL CABLE FROM THE BATTERY
CAUTION: Work must be started after 90 seconds from
the time the ignition switch is turned to the LOCK posi-
tion and the negative (±) terminal cable is disconnected
from the battery (See page RS±2).
2. DISCONNECT AIRBAG CONNECTOR
(a) Remove the glove compartment door finish plate inside the glove compartment.
NOTICE: When handling the airbag connector, take care
not to the airbag wire harness.
(b) Pull up the connector.
(c) Disconnect the airbag connector.
3. CONFIRM FUNCTIONING OF SST (See page RS±27)
SST 09082±00700
4. INSTALL SST
(a) Connect the SST connector to the front passenger airbag assembly connector.
NOTICE: To avoid damaging the SST connector and wire
harness, do not lock the secondary lock of the twin lock.
SST 09082±00700
±
SUPPLEMENTAL RESTRAINT SYSTEM FRONT PASSENGER AIRBAG ASSEMBLYRS±35
WhereEverybodyKnowsYourName
Page 3140 of 4087

(b) Move the SST to at least 10 m (33 ft) from the front of thevehicle.
(c) Close all the doors and windows of the vehicle. NOTICE: Take care not change the SST wire harness.
(d) Connect the SST red clip to the battery positive (+) terminal and the black clip to the battery negative (±) terminal.
5. DEPLOY AIRBAG
(a) Confirm that no±one is inside the vehicle or within 10 m (33ft) of the vehicle.
(b) Press the SST activation switch and deploy the airbag. HINT: The airbag deploys simultaneously as the LED of the
SST activation switch lights up.
6. DISPOSAL OF FRONT PASSENGER AIRBAG ASSEMBLY
NOTICE:
w The front passenger airbag assembly is very out not
when the airbag is deployed, so leave it alone for at least
30 minutes after deployment.
w Use gloves and safety glasses when handling a front
passenger airbag assembly with deployed airbag.
w Do not apply water, etc., to a front passenger airbag
assembly with deployed airbag.
w Always wash your hands with water after completing the
operation.
When scrapping a vehicle, deploy the airbag and scrap the
vehicle with the front passenger airbag assembly still
installed.
RS±36
±
SUPPLEMENTAL RESTRAINT SYSTEM FRONT PASSENGER AIRBAG ASSEMBLY
WhereEverybodyKnowsYourName
Page 3141 of 4087

When disposing of front passenger
airbag assembly only
When disposing of the front passenger airbag assembly
only, never use the customer's vehicle to deploy the air-
bag.
Remove the front passenger airbag assembly from the ve-
hicle and be sure to follow the procedure given below when
deploying the airbag.
HINT: Have a battery ready as the power source to deploy the
airbag.
1. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY CAUTION:
w When removing the front passenger airbag assembly,
work must be started after 90 seconds from the time the
ignition switch is turned to the LOCK position and the
negative (±) terminal cable is disconnected from the
battery.
w Store the front passenger airbag assembly with the
airbag door facing up.
2. FIX FRONT PASSENGER AIRBAG ASSEMBLY TO TIRE
Using a service±purpose wire harness for vehicle, tie down
the front passenger airbag assembly to the tire.
Wire harness: Stripped wire harness section
1.25 mm
2 or more (0.0019 in2 or more).
HINT: To calculate the square of the stripped wire harness
section±
Square = 3.14 x (Diameter)2 divided by 4
±
SUPPLEMENTAL RESTRAINT SYSTEM FRONT PASSENGER AIRBAG ASSEMBLYRS±37
WhereEverybodyKnowsYourName
Page 3142 of 4087

CAUTION: If a wire harness which is too thin or some oth-
er thing is used to tie down the front passenger airbag as-
sembly, it may be snapped by the shock when the airbag
is deployed, this is highly dangerous.
Always use a wire harness for vehicle use which is at
least 1.25 mm
2 (0.0019 in)2.
(1) Wrap the wire harness around the tire, passing the wire
harness at least 3 times through the installation hole on
the left and right sides of the front passenger airbag as-
sembly.
(2) Position the front passenger airbag assembly inside the tire with the airbag door facing inside.
Tie the wire harness to the tire.
Tire size: Must exceed the following dimensions
Width 185 mm (7.28 in.)
Inner diam 360 mm (14.17 in.)
CAUTION:
wMake sure the wire harness is tight. It is very dangerous
if a loose wire harness results in the front passenger
airbag assembly coming free due to the shock of the
airbag deploying.
w Always tie down the front passenger airbag assembly
with the airbag door facing inside.
NOTICE: The tire will be marked by the airbag deploy-
ment, so use a redundant tire.
3. CONFIRM FUNCTIONING OF SST (See page RS±27)
SST 09082±00700
RS±38
±
SUPPLEMENTAL RESTRAINT SYSTEM FRONT PASSENGER AIRBAG ASSEMBLY
WhereEverybodyKnowsYourName
Page 3143 of 4087

4. PLACE TIRES
(a) Place at least 2 tires under the tire to which the front
passenger airbag assembly is tied.
(b) Place at least 2 tires over the tire to which the front passenger
airbag assembly is tied. The top tire should have the wheel
installed.
(c) Tie the tires together by 2 wire harnesses. CAUTION: Make sure that the wire harnesses are tight. It
is very dangerous if looseness in the tires coming free
through the shock of the airbag deploying.
HINT: Place the SST connect and wire harness inside tires.
Provide at least 1 m (3 ft) of slack for the wire harness.
5. INSTALL SST Connect the SST connector to the front passenger airbag as-
sembly connector.
SST 09082±00700
NOTICE: To avoid damaging the SST connector and wire
harness, do not lock the secondary lock of the twin lock.
6. AIRBAG DEPLOYMENT
(a) Connect the SST red clip to the battery positive (+) terminal and the black clip to the battery negative (±) terminal.
(b) Confirm that no±one is within 10 m (33 ft) of the tire the front passenger airbag assembly is tied to.
(c) Press the SST activation switch and deploy the airbag.
±
SUPPLEMENTAL RESTRAINT SYSTEM FRONT PASSENGER AIRBAG ASSEMBLYRS±39
WhereEverybodyKnowsYourName
Page 3144 of 4087
7. DISPOSAL OF FRONT PASSENGER AIRBAGASSEMBLY
CAUTION:
w The front passenger airbag assembly is very hot when
the airbag is deployed, so leave it alone for at least 30
minutes after deployment.
w Use gloves and safety glasses when handling a front
passenger airbag assembly with deployed airbag.
w Do not apply water, etc., to a front passenger airbag
assembly with deployed airbag.
w Always wash your hand with water after completing the
operation.
(a) Remove the front passenger airbag assembly from the tire.
(b) Place the front passenger airbag assembly in a vinyl bag, tie
the end tightly and dispose of it the same way as other
general parts.
RS±40
±
SUPPLEMENTAL RESTRAINT SYSTEM FRONT PASSENGER AIRBAG ASSEMBLY
WhereEverybodyKnowsYourName