Page 1505 of 4087
(l) Install the accelerator bracket with the bolt and stud bolt.
(m) Install 2 new gaskets and union with the union bolt.
Torque: 29 NVm (300 kgf Vcm, 22 ft Vlbf)
(n) Connect the following hoses:
(1) Brake booster vacuum hose to union on air intake cham-
ber
(2) Vacuum hose (from VSV for heater water valve to air in-
take chamber
29. INSTALL THROTTLE BODY
(a) Disconnect the following hoses: (1) PCV hose to throttle body
(2) Water bypass hose to throttle body
(b) Install a new gasket and throttle body with the 2 bolts and 2 nuts.
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
HINT: Use bolt 40 mm (1.57 in.) in length.
(c) Install the water bypass pipe (from the rear bypass joint) to the clamp on the engine wire cover.
(d) Connect the following connectors: (1) Throttle position sensor connector
(2) w/ TRAC: Sub±throttle position sensor connector
(3) w/ TRAC: Sub±throttle actuator connector
±
1UZ±FE ENGINE ENGINE MECHANICALEG±129
WhereEverybodyKnowsYourName
Page 1506 of 4087
30. INSTALL HEATER WATER VALVE
(a) Install the water valve and bracket assembly with the 2 bolts.
(b) Install the engine wire with the bolt.
(c) Connect the VSV connector.
31. INSTALL IAC VALVE
(a) Install a new gasket and IAC valve with the 2 nuts.
Torque: 18 NVm (185 kgf Vcm, 13 ft Vlbf)
(b) Connect the water bypass hose (from the throttle body) to the
IAC valve.
(c) Connect the IAC valve connector.
32. INSTALL EGR VALVE ADAPTOR
(a) Install a new gasket, the EGR valve adaptor and EGR gas temperature sensor connector bracket with the 2 bolts and 2
nuts.
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
HINT: Use bolt 20 mm (0.78 in.) in length.
NOTICE: Do not touch the air intake chamber and adaptor sur-
faces of the gasket with your hand.
(b) Connect the PCV hose to the cylinder head.
(c) Connect the EGR gas temperature sensor connector.
EG±130
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName
Page 1507 of 4087

33. California:INSTALL EGR VALVE
(a) Place a new gasket on the EGR valve apaptor.
NOTICE:
w Do not touch the adaptor and EGR valve surfaces of the
gasket with your hand.
w Align the port holes of the gasket and adaptor. Be careful
of the installation direction.
(b) Install the EGR valve with the 2 nuts.
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
(c) Connect the following hoses:
(1) Water bypass hose to IAC valve
(2) Water bypass hose to water bypass pipe (from rear wa-ter bypass joint)
(d) Connect the EGR valve connector.
34. Except California: INSTALL EGR VALVE AND VACUUM MODULATOR
(a) Place a new gasket on the EGR valve adaptor.
NOTICE:
w Do not touch the adaptor and EGR valve surfaces of the
gasket with your hand.
w Align the port holes of the gasket and adaptor. Be careful
of the installation direction.
(b) Install the EGR valve and vacuum modulator assembly with
the bolt and 2 nuts.
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
±
1UZ±FE ENGINE ENGINE MECHANICALEG±131
WhereEverybodyKnowsYourName
Page 1508 of 4087
(c) Connect the following hoses:(1) Water bypass hose to IAC valve
(2) Water bypass hose to water bypass pipe(from rear water bypass joint)
(3) 2 vacuum hoses to VSV for EGR
(d) Install the hose clamp to the PCV hose.
35. INSTALL VACUUM PIPE
(a) Install the vacuum pipe, vacuum hose assembly and EGR water bypass pipe (California) with the 2 bolts.
(b) Connect the following hoses: (1) California: Vacuum hose to throttle body
(2) Except California: 3 vacuum hoses to throttle body
(3) Vacuum hose to fuel pressure regulator
(4) 2 vacuum hoses to VSV for fuel pressure control
(5) Except California: 2 vacuum hoses to EGR vacuum modulator
(6) 2 vacuum hoses (from VSV for EVAP) to vacuum pipe
(7) Vacuum hose (from VSV for fuel pressure) to air intake chamber
(8) Vacuum hose (from charcoal canister) to vacuum pipe
EG±132
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName
Page 1509 of 4087

36. INSTALL TIMING BELT REAR PLATESInstall the rear plate with the 2 bolts. Install the 2 rear plates.
Torque: 7.8 N Vm (80 kgf Vcm, 69 in. Vlbf)
37. INSTALL WATER INLET AND INLET HOUSING
(a) Remove any old packing (FIPG) material and be careful not
to drop any oil on the contact surfaces of the water inlet
housing and water pump.
wUsing a razor blade and gasket scraper, remove all the
old packing (FIPG) material from the gasket surfaces
and sealing groove.
w Thoroughly clean all components to remove all the
loose material.
w Using a non±residue solvent, clean both sealing
surfaces.
(b) Apply seal packing to the sealing groove of water inlet
housing as shown in the illustration.
Seal packing:
Part No. 08826±00100 or equivalent
wInstall a nozzle that has been cut to a 2±3 mm (0.08±0
12 in.) opening.
w Parts must be assembled within 5 minutes of
application. Otherwise the material must be removed
and reapplied.
w Immediately remove nozzle from the tube and reinstall
cap.
(c) Install a new O±ring to the water inlet housing.
(d) Apply soapy water on the O±ring.
(e) Push the water inlet housing end into the water pump hole.
(f) Install the water inlet and housing assembly with the 2 bolts. Alternately tighten the bolts.
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
HINT: Use bolts 25 mm (0.98 in.) in length.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±133
WhereEverybodyKnowsYourName
Page 1510 of 4087
(g) Connect the water bypass hose to the IAC valve.
38. INSTALL RH IGNITION COIL
(a) Install the ignition coil with the 2 bolts.
(b) Connect the ignition coil connector.
39. CONNECT CONTROL CABLES TO THROTTLE BODYConnect the following cables:
(1) Accelerator cable
(2) Transmission throttle control cable
(3) Cruise control actuator cable
40. INSTALL THROTTLE BODY COVER
(a) Install the thro ttle body cover and hose clamp with the cap nut
and 2 bolts.
(b) Install the EVAP hose to the hose clamp.
41. INSTALL POWER STEERING (PS) PUMP
(a) Install the PS pump with the nut and 3 bolts. Alternately tighten the bolts and nut.
Torque:
39 NVm (400 kgf Vcm, 29 ft Vlbf) for bolt
43 N Vm (440 kgf Vcm, 32 ft Vlbf) for nut
EG±134±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName
Page 1511 of 4087

(b) Connect the vacuum hose to the air intake chamber.
42. INSTALL TWC (FRONT)
(a) Using a 14 deep socket wrench, install a new gasket and theTWC with 3 new nuts. Install the 2 TWC.
Torque: 62 N Vm (630 kgf Vcm, 46 ft Vlbf)
(b) Te m p o r a r i l y i n s t a l l t h e p i p e s upport bracket to the
transmission with the 4 bolts.
(c) Install a new gasket to each front end of the front exhaust
pipe.
(d) Connect the front exhaust pipe to the 2 TWC with the 4 bolts and 4 new nuts.
Torque: 43 N Vm (440 kgf Vcm, 32 ft Vlbf)
(e) Tighten the 4 bolts holding the pipe support bracket to the
transmission.
Torque: 43 N Vm (440 kgf Vcm, 32 ft Vlbf)
43. INSTALL HYDRAULIC PUMP
Install the hydraulic pump with the 2 bolts and 2 nuts.
Torque:
16 NVm (160 kgf Vcm, 12 ft Vlbf) for 12 mm head
30 N Vm (310 kgf Vcm, 22 ft Vlbf) for 14 mm head
HINT: Each bolt length is indicated in the illustration.
Bolt length:
106 mm (4.17 in.) for A of 12 mm head
114 mm (4.49 in.) for B of 14 mm head
44. INSTALL RH CAMSHAFT TIMING PULLEY
(a) Align the camshaft knock pin with the knock pin groove of the
timing pulley, and slide on the timing pulley.
(b) Slide the timing pulley on the camshaft, facing the ªRº mark forward.
(c) Using SST, install the pulley bolt. SST 09278±54012
Torque: 108 N Vm (1,100 kgf Vcm, 80 ft Vlbf)
±
1UZ±FE ENGINE ENGINE MECHANICALEG±135
WhereEverybodyKnowsYourName
Page 1512 of 4087
45. INSTALL LH CAMSHAFT TIMING PULLEY
(a) Align the camshaft knock pin with the knock pin groove of the
timing pulley, and slide on the timing pulley.
(b) Slide the timing pulley on the camshaft, facing the ªLº mark forward.
(c) Using SST, install the pulley bolt. SST 09278±54012
Torque: 108 N Vm (1,100 kgf Vcm, 80 ft Vlbf)
46. C O N N E C T T I M I N G B E LT TO C A M S H A F T T I M I N G
PULLEYS
(See steps 10 to 40 on pages EG±61 to 72)
47. CONNECT NEGATIVE TERMINAL CABLE TO BATTERY
48. FILL WITH ENGINE COOLANT
49. START ENGINE AND CHECK FOR LEAKS
50. CHECK TRANSMISSION FLUID LEVEL
51. PERFORM ENGINE ADJUSTMENT (See Tune±Up on pages EG±9 to 34)
52. PERFORM ROAD TEST Check for abnormal noise, shock, slipage, correct shift points
and smooth operation.
53. INSTALL ENGINE UNDER COVER
EG±136
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName