1991 LEXUS SC400 service indicator

EVACUATING AIR IN
REFRIGERATION SYSTEM AND
CHARGING WITH REFRIGERANT
HINT: Before charging the system with refrigerant, be sure
carry out a complete evacuation of the system.
1. INSTALL MANIFOLD GAUGE SET TO SERVICE VALVES See page AC±15
2. EVACUATE AIR IN REFRIGERATION SYSTEM (a) Connect the center hose of the manifold gauge set to the vacuum pump.
(b) Open both the high and low hand valves and run the vacuum pump.
HINT: If opening the low pressure hand valve pulls the high
pressure gauge into the vacuum range, there is no blokage
in the system.
(c) After ten minutes or more, check that the low pressure gauge indicates 99.99 kPa (750 mmHg, 29.53 in.Hg) or
more of vacuum.
HINT: If the reading is not 99.99 kPa (750 mmHg, 29.53
in.Hg) or more of vacuum, close both the high and low hand
valves of the manifold gauge set and stop vaccum pump.
Then, check the system for leaks and repair as necessary.
(d) Close both the high and low hand valves and stop the
vacuum pump.
(e) Leave the system in this condition for five minutes or longer and check that there is no change in the gauge
indicator.
3. INSTALL CHARGING CYLINDER NOTICE: When handling the charging cylinder, always
follow the directions given in the instruction manual.
(a) Charge the proper amount of refrigerant in charging cylinder.
(b) Connect the center hose to charging cylinder. NOTICE: Do not open both high and low hand valves of
manifold guage set.
(c) Press on the schrader valve on the side of manifold gauge and expel the air inside of the center hose.
±
AIR CONDITIONING SYSTEM Evacuation Air in Refrigeration
System and Charging with RefrigerantAC±17
WhereEverybodyKnowsYourName

EQUIPMENT
AT06V±05\
 \
Feeler gauge Check major clearance\
 
\

\
Vernier calipers
 

Check length of second coast brake
piston rod.
\
 
\

\
Dial indicator or dial indicator with magnetic baseCheck piston stroke and end play of
the output shaft.
\
 
\

\
Dial indicator with magnetic baseCheck inside diameter of major
bushing.
\
 \
Straight edgeCheck side clearance of oil pump.
\
 \
Torque wrench
\
 
\

\
Cylinder gaugeCheck inside diameter of the trans-
mission case rear bushing.
\
 \
Voltmeter
\
 \
Ammeter(A)
\
 \
Ohmmeter
LUBRICANT
AT0GW±03
 Item Capacity Classification
 Automatic transmission fluid
 Dry fill 8.2 liters (8.7 US qts, 7.2 lmp. qts) ATF Type T±II or equivalent
 Drain and refill 1.9 liters (2.0 US qts, 1.7 lmp. qts) 
SSM (SPECIAL SERVICE MATERIALS)
AT06X±03
\
 \
08826±00090 Seal Packing 1281, Transmission case X Oil pan
\
 
\

\

THREE BOND 128\
1 or equivalentTransmission case X Extension
housing
±
A304E (1UZ±FE) AUTOMATIC TRANSMISSION PREPARATIONAT±13
WhereEverybodyKnowsYourName

RECOMMENDED TOOLS (Cont'd)
For suspending engine
09090±04010Engine Sling
Device
Plug for the vacuum hose. fuel hose etc.
09258±00030Hose Plug Set
09200±00010Engine Adjust
Kit
EQUIPMENT
 Part Name\
 \
Note
 Caliper gauge\
 \

 CO/HC analyzer\
 \

 

Compression gauge
\
 
\

\
Cylinder compression pressure
 Connecting rod aligner\
 \

 Cylinder gauge\
 \

 Dial indicator\
 \

 

Engine tune±up tester
\
 
\

\

 Feeler gauge\
 \

 Micrometer\
 \

 

Straight edge\
 
\

\

 Spring tester\
 \
Valve spring
 Steel square\
 \
Valve spring
 Torque wrench\
 \

 

Vernier caliper
\
 
\

\

SSM (SPECIAL SERVICE MATERIALS)
 

Part Name 

Part No.\
 

\
Use etc.
 

Seal packing or equivalent 

08826±00080\
 

\

Camshaft bearing cap, Cylinder head cover,
Rear oil seal retainer and Oil pump
 




Adhesive 1324,
THREE BOND 1324 or equivalent
 




08833±00070
\
 



\

Drive plate mounting bolt
 




Adhesive 1344,
THREE BOND 1344,
LOCTITE 242 or equivalent 




08833±00080
\
 



\

Idler pulley mounting bolt
EM±6±
ENGINE MECHANICAL Preparation
WhereEverybodyKnowsYourName

EQUIPMENT
 


Part Name\
 
\

\
Note
 Caliper gauge\
 \

 


HC/CO meter
\
 
\

\

 


Compression gauge\
 
\

\
Cylinder compression pressure
 Connecting rod aligner\
 \

 


Cylinder gauge
\
 
\

\

 


Dial indicator
\
 
\

\

 


Engine turn±up tester\
 
\

\

 Feeler gauge\
 \

 


Micrometer
\
 
\

\

 


Precision straight edge\
 
\

\

 Spring tester\
 \
Valve spring
 


Steel square
\
 
\

\
Valve spring
 


Torque wrench\
 
\

\

 Vernier caliper\
 \

SSM (SPECIAL SERVICE MATERIALS)
 
Part Name
 
Part No.
\
 \

Use etc.  \
 \

Camshaft bearing cap  \
 \
Camshaft bearing ca
Cylinder head semi±circular plug 
Seal packing or equivalent
 
08826±00080
\
 \
Cylinder head semi±circular lug
Cylinder head cover Seal acking or equivalent 08826±00080\
 \
Cylinder head cover
Rear oil seal retainer  \
 \
Rear oil seal retainer
Oil pump  \
 \

Water inlet housing Seal packing 1282B,
Th b d 1282B i l t
 08826±00100\
 \
Water inlet housing
Water seal plate Three bond 1282B or equivalent 08826±00100\
 \
Water seal late
Water pump 

Adhesive 1324,
Three bond 1324 or equivalent
 

08833±00070
\
 

\
Drive plate mounting bolt
 
Adhesive 1344,
 \
 \

 Adhesive 1344,
Three bond 1344
,
 
08833±00080
\
 \

No.1 idler pulley mounting bolt Three bond 1344,
Loctite 242 or equivalent 08833±00080\
 \
No.1 idler ulley mounting bolt
±
ENGINE MECHANICAL PreparationEM±7
WhereEverybodyKnowsYourName

PREPARATION
SST (SPECIAL SERVICE TOOLS)
PR01A±04
RECOMMENDED TOOLS
PR01B±02
EQUIPMENT
PR01C±02
\
 
\


\

\

Torque wrench 




\
 
\

\

Dial indicator 


\
 
\


\

\

Vernier calipers
 




±
PROPELLER SHAFT PRECAUTION, TROUBLESHOOTINGPR±3
WhereEverybodyKnowsYourName

PREPARATION
SST (SPECIAL SERVICE TOOLS)
PR02W±03
EQUIPMENT
PR02X±01\
 
\


\

\

Torque wrench
 




\
 
\

\

Dial indicator
\
 
\

\
Vernier calipers
±
PROPELLER SHAFT PREPARATIONPR±21
WhereEverybodyKnowsYourName

PREPARATION
SST (SPECIAL SERVICE TOOLS)
09201±41020Valve Stem Oil
Seal ReplacerArmature rear bearing
09286±46011Injection Pump
Spline Shaft PullerArmature front bearing
09612±24014
Steering Gear
Housing Overhaul
Tool Set
(09617±24011)(Steering Rack
Wrench)Fuel Inlet hose
09950±00020Bearing Remover
Armature rear bearing
RECOMMENDED TOOLS
09082±00015TOYOTA
Electrical Tester
EQUIPMENT
Part NameNote
Dial indicatorCommutator
Vernier caliperCommutator, Brush
Pull scaleBrush spring
Torque wrench
ST±4±
STARTING SYSTEM Preparation
WhereEverybodyKnowsYourName

EQUIPMENT
 


Part Name\
 
\

\
Note
 Caliper gauge\
 \

 


HC/CO meter
\
 
\

\

 


Compression gauge\
 
\

\
Cylinder compression pressure
 Connecting rod aligner\
 \

 


Cylinder gauge
\
 
\

\

 


Dial indicator
\
 
\

\

 


Engine turn±up tester\
 
\

\

 Feeler gauge\
 \

 


Micrometer
\
 
\

\

 


Precision straight edge\
 
\

\

 Spring tester\
 \
Valve spring
 


Steel square
\
 
\

\
Valve spring
 


Torque wrench\
 
\

\

 Vernier caliper\
 \

SSM (SPECIAL SERVICE MATERIALS)
 
Part Name
 
Part No.
\
 \

Use etc.  \
 \

Camshaft bearing cap  \
 \
Camshaft bearing ca
Cylinder head semi±circular plug 
Seal packing or equivalent
 
08826±00080
\
 \
Cylinder head semi±circular lug
Cylinder head cover Seal acking or equivalent 08826±00080\
 \
Cylinder head cover
Rear oil seal retainer  \
 \
Rear oil seal retainer
Oil pump  \
 \

Water inlet housing Seal packing 1282B,
Th b d 1282B i l t
 08826±00100\
 \
Water inlet housing
Water seal plate Three bond 1282B or equivalent 08826±00100\
 \
Water seal late
Water pump 

Adhesive 1324,
Three bond 1324 or equivalent
 

08833±00070
\
 

\
Drive plate mounting bolt
 
Adhesive 1344,
 \
 \

 Adhesive 1344,
Three bond 1344
,
 
08833±00080
\
 \

No.1 idler pulley mounting bolt Three bond 1344,
Loctite 242 or equivalent 08833±00080\
 \
No.1 idler ulley mounting bolt
±
ENGINE MECHANICAL PreparationEM±7
WhereEverybodyKnowsYourName