Page 1449 of 4087
CYLINDER HEAD
EG279±01
COMPONENTS FOR REMOVAL AND
INSTALLATION
±
1UZ±FE ENGINE ENGINE MECHANICALEG±73
WhereEverybodyKnowsYourName
Page 1450 of 4087
EG±74±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName
Page 1451 of 4087
EG24R±02
CYLINDER HEADS REMOVAL
(See Components for Removal and Installation)
1. DISCONNECT TIMING BELT FROM CAMSHAFT TIMING PULLEYS
(See steps 1 to 29 on pages EG±46 to 54)
2. REMOVE CAMSHAFT TIMING PULLEYS Using SST, remove the bolt and timing pulley. Remove the 2
timing pulleys.
SST 09278±54012
3. REMOVE FAN BRACKET Remove the 2 bolts, 2 nuts and fan bracket.
NOTICE:
w Be careful not to drop anything inside the timing belt
cover.
w Do not allow the belt to come into correct with oil, water
or dust.
4. DISCONNECT POWER STEERING (PS) PUMP FROM
ENGINE
(a) Disconnect the vacuum hose from the air intake chamber.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±75
WhereEverybodyKnowsYourName
Page 1452 of 4087

(b) Remove the nut and 3 bolts, and disconnect the PS pumpfrom the engine.
5. REMOVE TWC (FRONT)
(a) Remove the 4 bolts holding the pipe support bracket to the transmission.
(b) Remove the 4 bolts and nuts holding the front exhaust pipe to the TWC, and remove the pipe support bracket.
(c) Disconnect the front exhaust pipe from the TWC, and remove
the 2 gaskets.
(d) Using a 14 mm deep socket wrench, remove the 3 nuts, TWC
and gasket. Remove the 2 TWC.
6. REMOVE THROTTLE BODY COVER
(a) Disconnect the EVAP hose from the hose clamp.
(b) Remove the cap nut.
(c) Loosen the 2 bolts, and remove the hose clamp and throttle body cover.
7. DISCONNECT CONTROL CABLES FROM THROTTLE BODY
Disconnect the following cables:
(1) Accelerator cable
(2) Transmission throttle control cable
(3) Cruise control actuator cable
8. REMOVE RH IGNITION COIL
(a) Disconnect the ignition coil connector.
(b) Remove the 2 bolts and ignition coil.
EG±76
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName
Page 1453 of 4087
9. REMOVE WATER INLET AND INLET HOUSING
(a) Disconnect the water bypass hose from the IAC valve.
(b) Remove the 2 bolts holding the water inlet housing to waterpump.
(c) Pull out the water inlet and inlet housing assembly.
(d) Remove the O±ring from the water inlet housing.
10. REMOVE TIMING BELT REAR PLATES
Remove the 2 bolts and rear plate. Remove the 2 rear plates.
11. REMOVE VACUUM PIPE
(a) Disconnect the following hoses: (1) California:
Vacuum hose from throttle body
(2) Except California: 3 vacuum hoses from throttle body
(3) Vacuum hose from fuel pressure regulator
(4) 2 vacuum hoses from VSV for fuel pressure control
(5) Except California:
2 vacuum hoses from EGR vacuum modulator
(6) 2 vacuum hoses (from VSV for EVAP) from vacuum pipe
(7) Vacuum hose (from VSV for fuel pressure) from air in-
take chamber
(8) Vacuum hose (from charcoal canister) from vacuum pipe
±
1UZ±FE ENGINE ENGINE MECHANICALEG±77
WhereEverybodyKnowsYourName
Page 1454 of 4087
(b) Remove the 2 bolts, the vacuum pipe and hoses assembly.
12. California:REMOVE EGR VALVE
(a) Disconnect the EGR valve connector.
(b) Disconnect the following hoses:
(1) Water bypass hose from IAC valve
(2) Water bypass hose from water bypass pipe (from rearwater by5pass joint)
(c) Remove the 2 nuts, EGR valve and gasket.
13. Except California: REMOVE EGR VALVE AND VACUUM MODULATOR
(a) Disconnect the following hoses:
(1) Water bypass hose from IAC valve
(2) Water bypass hose from water bypass pipe (from rearwater bypass joint)
(3) 2 vacuum hoses from VSV for EGR
(b) Disconnect the hose clamp from the PCV hose.
EG±78
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName
Page 1455 of 4087
(c) Remove the bolt, 2 nuts, the EGR valve, vacuum modulatorassembly and gasket.
14. REMOVE EGR VALVE ADAPTOR
(a) Disconnect the EGR gas temperature sensor connector.
(b) Disconnect the PCV hose from the cylinder head.
(c) Remove the 2 bolts, 2 nuts, EGR adaptor and gasket.
15. REMOVE IAC VALVE
(a) Disconnect the IAC valve connector.
(b) Disconnect the water bypass hose from the IAC valve.
(c) Remove the 2 nuts, IAC valve and gasket.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±79
WhereEverybodyKnowsYourName
Page 1456 of 4087
16. REMOVE HEATER WATER VALVE FROM BODY
(a) Disconnect the VSV connector.
(b) Disconnect the bolt holding the engine wire clamp to thewater valve bracket.
(c) Remove the 2 bolts, and disconnect the water valve and bracket assembly.
17. REMOVE THROTTLE BODY
(a) Disconnect the following connectors: (1) Throttle position sensor connector
(2) w/ TRAC:
Sub±throttle position sensor connector
(3) w/ TRAC: Sub±throttle actuator connector
(b) Remove the 2 bolts and 2 nuts, and disconnect the throttle body from the air intake chamber.
(c) Disconnect the following hoses, and remove the throttle body:
(1) PCV hose from throttle body
(2) Water bypass hose from throttle body
(d) Remove the throttle body gasket.
18. REMOVE AIR INTAKE CHAMBER
(a) Disconnect the following hoses: (1) Brake booster vacuum hose from union on air intake
chamber
(2) Vacuum hose (from VSV for heater water valve) from air
intake chamber
EG±80
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName