Page 2777 of 4366
ROOF SIDE MOLDING EI-33
C
D E
F
G H
J
K L
M A
B
EI
Revision: 2006 July 2007 FX35/FX45
ROOF SIDE MOLDINGPFP:73854
Removal and InstallationNIS001TZ
REMOVAL
Disconnect molding from roof side clip and remove roof side molding.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
To install roof side molding, check if all clips are matched over holes of panel on vehicle, then push it.
PIIA4951E
1. Roof side molding
Page 2778 of 4366
EI-34
ROOF RAIL
Revision: 2006 July 2007 FX35/FX45
ROOF RAILPFP:73820
Removal and InstallationNIS001U0
REMOVAL
1. Remove cover roof rail (front/rear).
2. Remove nuts of roof rail and remove roof rail assembly.
INSTALLATION
Install in the reverse order of removal.
REMOVAL AND INSTALLATION OF ROOF RAIL BRACKET
Removal
1. Remove roof rail assembly.
2. Remove roof side molding. Refer to EI-33, "
ROOF SIDE MOLDING" .
3. Remove headlining. Refer to EI-43, "
HEADLINING" .
4. Remove nuts of roof rail bracket assembly and remove roof rail bracket assembly.
Installation
Install in the reverse order of removal.
CAUTION:
Replace sealing washer.
1. Cover roof rail (front) 2. Nut 3. Roof rail assembly
4. Rubber seal (front) 5. Roof side molding 6. Roof rail bracket assembly
7. Seal 8. Nut 9. Rubber seal (rear)
10. Cover roof rail (rear)
PIIA4948E
Page 2779 of 4366
BACK DOOR FINISHER EI-35
C
D E
F
G H
J
K L
M A
B
EI
Revision: 2006 July 2007 FX35/FX45
BACK DOOR FINISHERPFP:90900
Removal and InstallationNIS002AG
REMOVAL
1. Remove back door finisher inner. Refer to EI-47, "Removal and Installation" .
2. Remove back door outside finisher upper nuts and back door outside finisher upper.
3. Remove back door outside finisher lower nuts and back door outside finisher lower.
INSTALLATION
Install in the reverse order of removal.
1. Back door outside finisher upper 2. Bolt 3. Nut
4. Clip 5. Back door outside finisher lower
PIIA4327E
Page 2780 of 4366
EI-36
DOOR FINISHER
Revision: 2006 July 2007 FX35/FX45
DOOR FINISHERPFP:80900
Removal and InstallationNIS001U1
DOOR FINISHER (FRONT AND REAR)
Removal
1. Remove door finisher cap of inside handle portion and remove bolt.
2. Remove door grip cap and remove bolts of door grip portion.
3. Insert screw driver rolled with cloth between panel on vehicle and clips (as indicated with arrow), and remove finisher.
4. Pull up door finisher, and remove electrical parts connectors.
1. Door finisher (front) 2. Clip (C101) 3. Bolt
4. Door grip cap 5. Door finisher cap 6. Door finisher (rear)
7. Seat memory switch finisher 8. Seat memory switch Clip Pawl Metal clip
PIIB8502E
SIIA0810E
Page 2781 of 4366
DOOR FINISHER EI-37
C
D E
F
G H
J
K L
M A
B
EI
Revision: 2006 July 2007 FX35/FX45
5. Remove lock knob cable, inside handle cable and illumination
harness connector (front door only) from backside of inside han-
dle assembly.
6. Remove the following parts after removing door finisher.
Inside handle
Seat memory switch and seat memory switch finisher
Power window switch
Ste p l am p
Installation
Install in the reverse order of removal.
CAUTION:
To install finisher, check if all clips are matched over holes of panel on vehicle, then push it.
PIIA4959E
Page 2782 of 4366
EI-38
BODY SIDE TRIM
Revision: 2006 July 2007 FX35/FX45
BODY SIDE TRIMPFP:76913
Removal and InstallationNIS001U2
CAUTION:
Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.
CENTER PILLAR LOWER GARNISH
Removal
1. Remove front and rear kicking plate.
2. Remove front and rear body side welt.
1. Front pillar garnish 2. Front body side welt 3. Dash side finisher
4. Nut 5. Front kicking plate 6. Center pillar lower garnish
7. Center pillar upper garnish 8. Bolt 9. Center pillar upper cap
10. Rear body side welt 11. Rear kicking plate 12. Clip (C203)
13. Center mudguard finisher (rear) 14. Center mudguard finisher (front)
PIIA4340E
PIIA4344E
Page 2783 of 4366

BODY SIDE TRIM EI-39
C
D E
F
G H
J
K L
M A
B
EI
Revision: 2006 July 2007 FX35/FX45
3. Remove center pillar lower garnish.
NOTE:
Insert screwdriver rolled with cloth between panel on vehicle and
clips, then disconnect clips.
Installation
Install in the reverse order of removal.
NOTE:
To install, check if all clips are matched over holes of panel on vehicle, then push on.
CENTER PILLAR UPPER GARNISH
Removal
1. Remove seat belt shoulder anchor. Refer to SB-4, "Removal and Installation of Front Seat Belt" .
2. Remove front and rear kicking plate.
3. Remove front and rear body side welt.
4. Remove center pillar lower garnish.
5. Remove center pillar upper cap and bolt.
6. Remove center pillar upper garnish.
Installation
Install in the reverse order of removal.
DASH SIDE FINISHER
Removal
1. Remove front kicking plate.
2. Remove front body side welt.
3. Remove nut.
4. Remove dash side finisher.
NOTE:
Insert screwdriver rolled with cloth between panel on vehicle and
clips, then disconnect clips.
Installation
Install in the reverse order of removal.
NOTE:
To install, check if all clips are matched over holes of panel on vehicle, then push on.
PIIA4341E
PIIA4342E
PIIA4343E
Page 2784 of 4366
EI-40
BODY SIDE TRIM
Revision: 2006 July 2007 FX35/FX45
FRONT PILLAR GARNISH
Removal
Remove front pillar garnish clips and remove front pillar garnish.
Installation
Install in the reverse order of removal.
KICKING PLATE
Removal
Remove kicking plate clips and remove kicking plate.
Installation
Install in the reverse order of removal.
CENTER MUDGUARD FINISHER (FRONT/REAR)
Removal
1. Remove center mudguard finisher (front).
2. Remove center mudguard finisher clip and remove center mud- guard finisher (rear).
Installation
Install in the reverse order of removal.
PIIA4345E
PIIA4346E