Page 433 of 3924

ATC-28
< SERVICE INFORMATION >
AIR CONDITIONER CONTROL
When pressing AUTO switch, air inlet, air outlet, fan speed, and discharge air temperature are automatically
controlled.
TEMPERATURE CONTROL SWITCH (POTENTIO TEMPERATURE CONTROL) (DRIVER SIDE)
The set temperature is increased or decreased with this switch.
TEMPERATURE CONTROL SWITCH (POTENTIO TEMPERATURE CONTROL) (PASSENGER
SIDE)
The set temperature is increased or decreased with this switch.
When the temperature switch is pressed, the DUA L switch indicator will automatically illuminate.
INTAKE SWITCH
When intake switch is ON, REC LED turns ON, and air inlet is fixed to REC.
When press intake switch again, FRE LED turns ON, and air inlet is fixed to FRE.
When intake switch is pressed for approximately 1. 5 seconds or longer, FRE and REC LEDs blink twice.
Then, automatic control mode is entered. Inlet status is displayed by LED even during automatic controlled.
When FRE LED is turned ON, shifting mode position to D/ F or DEF, or when compressor is turned from ON
to OFF, intake switch is automatically turned OFF (fixed to FRE mode). REC mode can be re-entered by
pressing intake switch again, and then compressor is turned ON. (Except D/F or DEF position)
DEFROSTER (DEF) SWITCH
Mode doors are set to the defrost position with this switch . Also, intake doors are set to the outside air position,
and compressor turns ON.
REAR WINDOW DEFOGGER SWITCH
When illumination is ON, rear window is defogged.
OFF SWITCH
Compressor and blower are OFF, the intake door s and the mode doors are automatically controlled.
A/C SWITCH
Compressor is ON or OFF with this switch.
(Pressing the A/C switch when the A/C switch is ON will turn OFF the A/C switch and compressor.)
MODE SWITCH
The air discharge outlets is controlled with this switch.
FAN SWITCH
The blower speed is manually controlled with this swit ch. Seven speeds are available for manual control (as
shown on the display screen).
DUAL SWITCH
When the DUAL switch indicator is illuminated, the driver side and passenger side temperature can each be set independently.
When the DUAL switch indicator is not illuminated, t he driver side setting temperature is applied to both
sides.
Fail-Safe FunctionINFOID:0000000001328171
If a communication error exists between the unified meter and A/C amp., and the A/C and AV switch for 30
seconds or longer, air conditioner is controlled under following conditions:
Compressor : ON
Air outlet : AUTO
Air inlet : FRE (Fresh)
Blower fan speed : AUTO
Set temperature : Setting befo re communication error occurs
Display : OFF
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C
Page 434 of 3924
AIR CONDITIONER CONTROLATC-29
< SERVICE INFORMATION >
C
DE
F
G H
I
K L
M A
B
AT C
N
O P
Discharge Air FlowINFOID:0000000001328172
SJIA1568E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C
Page 435 of 3924
ATC-30
< SERVICE INFORMATION >
AIR CONDITIONER CONTROL
System Description
INFOID:0000000001328173
SWITCHES AND THEIR CONTROL FUNCTION
CAN Communication System DescriptionINFOID:0000000001328174
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication s peed and excellent error detection ability. Many elec-
SJIA1610E
SJIA1890E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C
Page 436 of 3924
AIR CONDITIONER CONTROLATC-31
< SERVICE INFORMATION >
C
DE
F
G H
I
K L
M A
B
AT C
N
O P
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only. For details, refer to LAN-43,
"CAN System Specification Chart".
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C
Page 437 of 3924

ATC-32
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
TROUBLE DIAGNOSIS
CONSULT-III FunctionINFOID:0000000001328175
CONSULT-III can display each diagnosis item using the diagnosis test modes shown following.
DATA MONITOR
Display Item List
How to Perform Trouble Diagnosis for Quick and Accurate RepairINFOID:0000000001328176
WORK FLOW
SYMPTOM TABLE
System part Check item, diagnosis mode Description
BCM Data monitor Displays BCM input data in real time.
Monitor item name “operation or unit” Contents
IGN ON SW “On/Off” Displays “IGN position (On)/OFF, ACC position (Off)” status as judged from ignition switch signal.
FAN ON SIG “On/Off” Displays “FAN (On)/FAN (Off)” status as judged from blower fan motor switch signal.
AIR COND SW “On/Off” Di splays “COMP (On)/COMP (Off)” status as judged from air conditioner switch signal.
*1AT C - 5 0 , "Operational Check"
SHA900E
Symptom Reference Page
A/C system does not come on. Go to Trouble Diagnosis Procedure for A/C System. AT C - 5 2 , "
Power
Supply and Ground
Circuit for Auto
Amp"
A/C system cannot be controlled.
Go to Integrated Display System.
Go to Navigation System. AV- 7 9 , "
Unable to
Operate System
with A/C and AV
Switch" (Without
navigation system)
or AV- 1 2 7 , "
Unable
to Operate System
with A/C and AV
Switch" (With navi-
gation system)
Air outlet does not change. Go to Trouble Diagnosis Procedure for Mode Door Motor. (LAN) AT C - 5 7 , "
Mode
Door Motor Circuit"Mode door motor does not operate normally.
Discharge air temperature does not change.
Go to Trouble Diagnosis Procedure for Air Mix Door Motor. (LAN) AT C - 5 9 , "
Air Mix
Door Motor Circuit"Air mix door motor does not operate normal-
ly.
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C
Page 438 of 3924

TROUBLE DIAGNOSISATC-33
< SERVICE INFORMATION >
C
DE
F
G H
I
K L
M A
B
AT C
N
O P
Intake door does not change. Go to Trouble Diagnosis Procedure for Intake Door Motor. (LAN) AT C - 6 2 , "Intake
Door Motor Circuit"Intake door motor does not operate normally.
Blower motor operation is malfunctioning. Go to Trouble Diagnosis Procedure for Blower Motor.
AT C - 6 4 , "
Blower
Motor Circuit"
Magnet clutch does not engage. Go to Trouble Diagnosis Procedure for Magnet Clutch.AT C - 6 9 , "Magnet
Clutch Circuit"
Insufficient cooling Go to Trouble Diagnosis Procedure for Insufficient Cooling.
AT C - 7 5 , "Insufficient
Cooling"
Insufficient heating Go to Trouble Diagnosis Procedure for Insufficient Heating.AT C - 8 2 , "Insufficient
Heating"
Noise Go to Trouble Diagnosis Procedure for Noise.
AT C - 8 3 , "Noise"
Self-diagnosis cannot be performed. Go to Trouble Diagnosis Procedure for Self-diagnosis.AT C - 8 4 , "Self-Diag-
nosis"
Memory function does not operate. Go to Trouble Diagnosis Procedure for Memory Function.
AT C - 8 5 , "Memory
Function"
Symptom Reference Page
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C
Page 439 of 3924
ATC-34
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
Component Parts and Harn ess Connector Location
INFOID:0000000001328177
ENGINE COMPARTMENT
RJIA1963E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C
Page 440 of 3924
TROUBLE DIAGNOSISATC-35
< SERVICE INFORMATION >
C
DE
F
G H
I
K L
M A
B
AT C
N
O P
PASSENGER COMPARTMENT
SJIA1606E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C