Page 305 of 3924

AT-232
< SERVICE INFORMATION >
ON-VEHICLE SERVICE
9. Install bearing race to output shaft.
10. Apply recommended sealant (Genuine Anaerobic Liquid Gasketor equivalent. Refer to GI-44, "
Recommended Chemical Product
and Sealant".) to rear extension assembly as shown in the fig-
ure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc.
from the transmission case and rear extension assembly
mounting surfaces.
11. Install rear extension assembly to transmission case. (With nee- dle bearing.)
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.
12. Tighten rear extension assembly mounting bolts to specified torque. Refer to "COMPONENTS".
CAUTION:
Do not reuse self-sealing bolts.
13. Install engine mounting insulator (rear). Refer to AT-241, "
Removal and Installation (2WD Models)".
14. Install rear engine mounting member. Refer to AT-241, "
Removal and Installation (2WD Models)".
15. Install control rod. Refer to AT-206, "
Control Rod Removal and Installation".
16. Install rear propeller shaft. Refer to PR-9, "
Removal and Installation".
17. Install exhaust front tube and center muffler. Refer to EX-3, "
Component".
18. Install drain plug in oil pan, and then tighten drain plug to the specified torque. Refer to AT-215, "
Control
Valve with TCM and A/T Fluid Temperature Sensor 2".
CAUTION:
Do not reuse drain plug gasket.
19. Pour ATF into A/T assembly. Refer to AT- 11 , "
Changing A/T Fluid".
SCIA5245E
SCIA8228E
SCIA3431E
SCIA6941E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C
Page 306 of 3924

ON-VEHICLE SERVICEAT-233
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
Rear Oil SealINFOID:0000000001327395
REMOVAL
1. Remove center muffler with power tool. Refer to EX-3, "Compo-
nent".
2. Remove rear propeller shaft. Refer to PR-9, "
Removal and
Installation".
3. Remove front propeller shaft (AWD models). Refer to PR-4,
"Removal and Installation".
4. Remove transfer assembly from A/T assembly (AWD models). Refer to TF-40, "
Removal and Installation".
5. Remove rear oil seal using a flat-bladed screwdriver. CAUTION:
Be careful not to scratch rear extension assembly (2WD
models) or adapter case assembly (AWD models).
INSTALLATION
CAUTION:
After completing installati on, check A/T fluid leakage and A/T fluid level. Refer to AT- 11 , "
Checking A/T
Fluid".
1. As shown in the figure, use the drift to drive rear oil seal into rear extension assembly (2WD models) or adapter case assembly
(AWD models) until it is flush.
CAUTION:
Do not reuse rear oil seal.
Apply ATF to rear oil seal.
2. Install transfer assembly to A/T assembly (AWD models). Refer to TF-40, "
Removal and Installation".
3. Install front propeller shaft (AWD models). Refer to PR-4,
"Removal and Installation".
4. Install rear propeller shaft. Refer to PR-9, "
Removal and Installa-
tion".
5. Install center muffler. Refer to EX-3, "
Component".
Revolution Sensor Component (2WD Models Only)INFOID:0000000001327396
COMPONENTS
SCIA5410E
SCIA5411E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C
Page 307 of 3924

AT-234
< SERVICE INFORMATION >
ON-VEHICLE SERVICE
REMOVAL
1. Disconnect the battery cable from the negative terminal.
2. Drain ATF through drain plug.
3. Remove front cross bar. Refer to FSU-6, "
Removal and Installation".
4. Remove exhaust front tube and center muffler with power tool. Refer to EX-3, "
Component".
5. Remove rear propeller shaft. Refer to PR-9, "
Removal and Installation".
6. Remove control rod. Refer to AT-206, "
Control Rod Removal and Installation".
7. Remove clips (1), oil pan (2) and oil pan gasket. : Vehicle front
: Bolt (22)
Drain plug (3)
1. Rear extension 2. A/T 3. Oil pan gasket
4. Clip 5. Oil pan mounting bolt 6. Oil pan
7. Drain plug 8. Drain plug gasket 9. Revolution sensor
10. Self-sealing bolt
Refer to GI section to make sure icons (symbol marks) in the figure. Refer to GI-8, "
Component".
However, refer to the following symbol for others.
*: Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to GI-44, "Recommended Chemical Product and Sealant"
SCIA8043E
SCIA8117E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C
Page 308 of 3924

ON-VEHICLE SERVICEAT-235
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
8. Check foreign materials in oil pan to help determine causes of malfunction. If the ATF is very dark, smells burned, or contains
foreign particles, the frictional material (clutches, band) may
need replacement. A tacky film that will not wipe clean indicates
varnish build up. Varnish can c ause valves, servo, and clutches
to stick and can inhibit pump pressure.
If frictional material is detected, perform A/T fluid cooler
cleaning. Refer to AT-13, "
A/T Fluid Cooler Cleaning".
9. Support A/T assembly with a transmission jack. CAUTION:
When setting transmission jack, place wooden blocks to
prevent from damaging control valve with TCM and trans-
mission case.
10. Remove rear engine mounting member with power tool. Refer to AT-241, "
Removal and Installation (2WD
Models)".
11. Remove tightening bolts for rear extension assembly and trans- mission case.
12. Tap rear extension assembly with soft hammer.
13. Remove rear extension assembly from transmission case. (With needle bearing.)
SCIA5199E
SCIA6941E
SCIA3432E
SCIA3431E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C
Page 309 of 3924

AT-236
< SERVICE INFORMATION >
ON-VEHICLE SERVICE
14. Disconnect revolution sensor connector.CAUTION:
Be careful not to damage connector
15. Straighten terminal clip to free revolution sensor harness.
16. Remove revolution sensor from transmission case. CAUTION:
Do not subject it to impact by dropping or hitting it.
Do not disassemble.
Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.
Do not place in an area affected by magnetism.
INSTALLATION
CAUTION:
After completing installation, check A/T position , A/T fluid leakage and A/F fluid level. Refer to AT-207,
"Checking of A/T Position", AT- 11 , "Checking A/T Fluid".
1. Install revolution sensor in transmission case, and then tighten revolution sensor mounting bolt to the specified torque. Refer to
"COMPONENTS".
CAUTION:
Do not subject it to impact by dropping or hitting it.
Do not disassemble.
Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.
Do not place in an area affected by magnetism.
SCIA7524E
SCIA7525E
SCIA3997E
SCIA3997E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C
Page 310 of 3924

ON-VEHICLE SERVICEAT-237
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
2. Connect revolution sensor connector.
3. Securely fasten revolution sensor harness with clip.
4. Apply recommended sealant (Genuine Anaerobic Liquid Gasket or equivalent. Refer to GI-44, "
Recommended Chemical Product
and Sealant".) to rear extension assembly as shown in the fig-
ure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc.
from transmission case and rear extension assembly
mounting surfaces.
5. Install rear extension assembly to transmission case. (With nee- dle bearing.)
CAUTION:
Insert the tip of parking rod between the parking pole and
the parking actuator suppor t when assembling the rear
extension assembly.
6. Tighten rear extension assembly mounting bolts to specified torque. Refer to "COMPONENTS".
CAUTION:
Do not reuse self-sealing bolts.
7. Install rear engine mounting member. Refer to AT-241,
"Removal and Installation (2WD Models)".
8. Install oil pan to transmission case.
a. Install oil pan gasket to oil pan. CAUTION:
Do not reuse oil pan gasket.
Install it in the direction to align hole positions.
SCIA7524E
SCIA7525E
SCIA8228E
SCIA3431E
SCIA6941E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C
Page 311 of 3924

AT-238
< SERVICE INFORMATION >
ON-VEHICLE SERVICE
Completely remove all moisture, oil and old gasket, etc. from oil pan mounting surface.
b. Install oil pan (2) (with oil pan gasket) and clips (1) to transmis- sion case.
: Vehicle front
: Bolt (22)
CAUTION:
Install it so that drain plug (3) comes to the position as
shown in the figure.
Be careful not to pinch harnesses.
Completely remove all moisture, oil and old gasket, etc. from oil pan mounting surface.
c. Tighten oil pan mounting bolts to the specified torque in numeri- cal order shown in the figure after temporarily tightening them.
Refer to "COMPONENTS".
CAUTION:
Do not reuse oil pan mounting bolts.
9. Install drain plug to oil pan, and then tighten drain plug to the specified torque. Refer to "COMPONENTS".
CAUTION:
Do not reuse drain plug gasket.
10. Install control rod. Refer to AT-206, "
Control Rod Removal and
Installation".
11. Install rear propeller shaft. Refer to PR-9, "
Removal and Installa-
tion".
12. Install exhaust front tube and center muffler. Refer to EX-3, "
Component".
13. Install front cross bar. Refer to FSU-6, "
Removal and Installation".
14. Pour ATF into A/T assembly. Refer to AT- 11 , "
Changing A/T Fluid".
15. Connect the battery cable to the negative terminal.
SCIA8117E
SCIA4113E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C
Page 312 of 3924
AIR BREATHER HOSEAT-239
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
AIR BREATHER HOSE
Removal and InstallationINFOID:0000000001327397
VQ35DE ENGINE MODEL
Refer to the figure below for air breather hose removal and installation procedure.
CAUTION:
When installing an air breather hose, be careful not to be crushed or blocked by folding or bending
the hose.
When inserting a hose to the transm ission tube, be sure to insert it fully until its end reaches the
tube bend R portion.
VK45DE ENGINE MODEL
SCIA2151E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C